[PATCH v2 2/3] arm64: dts: ti: k3-am62-main: Add support for USB

Sjoerd Simons sjoerd at collabora.com
Wed Dec 21 05:30:49 PST 2022


From: Aswath Govindraju <a-govindraju at ti.com>

AM62 SoC has two instances of USB on it. Therefore, add support for the
same.

Signed-off-by: Aswath Govindraju <a-govindraju at ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr at ti.com>
[cherry-pick from vendor BSP]]
Signed-off-by: Sjoerd Simons <sjoerd at collabora.com>

---

Changes in v2:
  - Rebase against linux-next 20221220

 arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 44 ++++++++++++++++++++++++
 1 file changed, 44 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
index 466b94d1cee9..4da15e8c956f 100644
--- a/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am62-main.dtsi
@@ -555,6 +555,50 @@ sdhci2: mmc at fa20000 {
 		status = "disabled";
 	};
 
+	usbss0: dwc3-usb at f900000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f900000 0x00 0x800>;
+		clocks = <&k3_clks 161 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4008>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 178 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+
+		usb0: usb at 31000000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31000000 0x00 0x50000>;
+			interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
+	usbss1: dwc3-usb at f910000 {
+		compatible = "ti,am62-usb";
+		reg = <0x00 0x0f910000 0x00 0x800>;
+		clocks = <&k3_clks 162 3>;
+		clock-names = "ref";
+		ti,syscon-phy-pll-refclk = <&wkup_conf 0x4018>;
+		#address-cells = <2>;
+		#size-cells = <2>;
+		power-domains = <&k3_pds 179 TI_SCI_PD_EXCLUSIVE>;
+		ranges;
+
+		usb1: usb at 31100000 {
+			compatible = "snps,dwc3";
+			reg =<0x00 0x31100000 0x00 0x50000>;
+			interrupts = <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>, /* irq.0 */
+				     <GIC_SPI 226 IRQ_TYPE_LEVEL_HIGH>; /* irq.0 */
+			interrupt-names = "host", "peripheral";
+			maximum-speed = "high-speed";
+			dr_mode = "otg";
+		};
+	};
+
 	fss: bus at fc00000 {
 		compatible = "simple-bus";
 		reg = <0x00 0x0fc00000 0x00 0x70000>;
-- 
2.39.0




More information about the linux-arm-kernel mailing list