[PATCH] ARM: dts: lan966x: add support for pcb8290

[Horatiu Vultur - M31836]

The 08/23/2022 07:11, Claudiu Beznea - M18063 wrote:

Hi Claudiu,

> > +&gpio {
> > +	miim_a_pins: mdio-pins {
> > +		/* MDC, MDIO */
> > +		pins =  "GPIO_28", "GPIO_29";
> > +		function = "miim_a";
> > +	};
> > +
> > +	pps_out_pins: pps-out-pins {
> 
> Can you also document this one as well? I can do it while applying if you
> provide the strings.

Yes, I will do that.
I will send a new version because I have seen that there is also a small
error in the commit message.

> 
> > +		pins = "GPIO_38";
> > +		function = "ptpsync_3";
> > +	};
> > +
> > +	ptp_ext_pins: ptp-ext-pins {
> 
> Ditto
> 
> Thank you,
> Claudiu Beznea
> 
> > +		pins = "GPIO_35";
> > +		function = "ptpsync_0";
> > +	};
> > +
> > +	udc_pins: ucd-pins {
> > +		/* VBUS_DET B */
> > +		pins = "GPIO_8";
> > +		function = "usb_slave_b";
> > +	};
> > +};
> > +
> > +&mdio0 {
> > +	pinctrl-0 = <&miim_a_pins>;
> > +	pinctrl-names = "default";
> > +	status = "okay";
> > +
> > +	ext_phy0: ethernet-phy at 7 {
> > +		reg = <7>;
> > +		coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > +	};
> > +
> > +	ext_phy1: ethernet-phy at 8 {
> > +		reg = <8>;
> > +		coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > +	};
> > +
> > +	ext_phy2: ethernet-phy at 9 {
> > +		reg = <9>;
> > +		coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > +	};
> > +
> > +	ext_phy3: ethernet-phy at 10 {
> > +		reg = <10>;
> > +		coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > +	};
> > +
> > +	ext_phy4: ethernet-phy at 15 {
> > +		reg = <15>;
> > +		coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > +	};
> > +
> > +	ext_phy5: ethernet-phy at 16 {
> > +		reg = <16>;
> > +		coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > +	};
> > +
> > +	ext_phy6: ethernet-phy at 17 {
> > +		reg = <17>;
> > +		coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > +	};
> > +
> > +	ext_phy7: ethernet-phy at 18 {
> > +		reg = <18>;
> > +		coma-mode-gpios = <&gpio 60 GPIO_ACTIVE_HIGH>;
> > +	};
> > +};
> > +
> > +&port0 {
> > +	reg = <2>;
> > +	phy-handle = <&ext_phy2>;
> > +	phy-mode = "qsgmii";
> > +	phys = <&serdes 0 SERDES6G(1)>;
> > +	status = "okay";
> > +};
> > +
> > +&port1 {
> > +	reg = <3>;
> > +	phy-handle = <&ext_phy3>;
> > +	phy-mode = "qsgmii";
> > +	phys = <&serdes 1 SERDES6G(1)>;
> > +	status = "okay";
> > +};
> > +
> > +&port2 {
> > +	reg = <0>;
> > +	phy-handle = <&ext_phy0>;
> > +	phy-mode = "qsgmii";
> > +	phys = <&serdes 2 SERDES6G(1)>;
> > +	status = "okay";
> > +};
> > +
> > +&port3 {
> > +	reg = <1>;
> > +	phy-handle = <&ext_phy1>;
> > +	phy-mode = "qsgmii";
> > +	phys = <&serdes 3 SERDES6G(1)>;
> > +	status = "okay";
> > +};
> > +
> > +&port4 {
> > +	reg = <6>;
> > +	phy-handle = <&ext_phy6>;
> > +	phy-mode = "qsgmii";
> > +	phys = <&serdes 4 SERDES6G(2)>;
> > +	status = "okay";
> > +};
> > +
> > +&port5 {
> > +	reg = <7>;
> > +	phy-handle = <&ext_phy7>;
> > +	phy-mode = "qsgmii";
> > +	phys = <&serdes 5 SERDES6G(2)>;
> > +	status = "okay";
> > +};
> > +
> > +&port6 {
> > +	reg = <4>;
> > +	phy-handle = <&ext_phy4>;
> > +	phy-mode = "qsgmii";
> > +	phys = <&serdes 6 SERDES6G(2)>;
> > +	status = "okay";
> > +};
> > +
> > +&port7 {
> > +	reg = <5>;
> > +	phy-handle = <&ext_phy5>;
> > +	phy-mode = "qsgmii";
> > +	phys = <&serdes 7 SERDES6G(2)>;
> > +	status = "okay";
> > +};
> > +
> > +&serdes {
> > +	status = "okay";
> > +};
> > +
> > +&switch {
> > +	pinctrl-0 = <&pps_out_pins>, <&ptp_ext_pins>;
> > +	pinctrl-names = "default";
> > +	status = "okay";
> > +};
> > +
> > +&udc {
> > +	pinctrl-0 = <&udc_pins>;
> > +	pinctrl-names = "default";
> > +	atmel,vbus-gpio = <&gpio 8 GPIO_ACTIVE_HIGH>;
> > +	status = "okay";
> > +};
> 

-- 
/Horatiu