[PATCH v4 2/2] remoteproc: meson-mx-ao-arc: Add a driver for the AO ARC remote procesor
Mathieu Poirier
mathieu.poirier at linaro.org
Mon Sep 27 09:19:55 PDT 2021
Hi Martin,
On Tue, Sep 21, 2021 at 09:25:57PM +0200, Martin Blumenstingl wrote:
> Amlogic Meson6, Meson8, Meson8b and Meson8m2 embed an ARC core in the
> Always-On (AO) power-domain. This is typically used for waking up the
> ARM cores after system suspend.
>
> The configuration is spread across three different registers:
> - AO_REMAP_REG0 which must be programmed to zero, it's actual purpose
> is unknown. There is a second remap register which is not used in the
> vendor kernel (which served as reference for this driver).
> - AO_CPU_CNTL is used to start and stop the ARC core.
> - AO_SECURE_REG0 in the SECBUS2 register area with unknown purpose.
>
> To boot the ARC core we also need to enable it's gate clock and trigger
> a reset.
>
> The actual code for this ARC core can come from an ELF binary, for
> example by building the Zephyr RTOS for an ARC EM4 core and then taking
> "zephyr.elf" as firmware. This executable does not have any "rsc table"
> so we are skipping rproc_elf_load_rsc_table (rproc_ops.parse_fw) and
> rproc_elf_find_loaded_rsc_table (rproc_ops.find_loaded_rsc_table).
>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> ---
> drivers/remoteproc/Kconfig | 11 ++
> drivers/remoteproc/Makefile | 1 +
> drivers/remoteproc/meson_mx_ao_arc.c | 261 +++++++++++++++++++++++++++
> 3 files changed, 273 insertions(+)
> create mode 100644 drivers/remoteproc/meson_mx_ao_arc.c
>
> diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
> index 9a6eedc3994a..3f8d5d80a0c4 100644
> --- a/drivers/remoteproc/Kconfig
> +++ b/drivers/remoteproc/Kconfig
> @@ -127,6 +127,17 @@ config KEYSTONE_REMOTEPROC
> It's safe to say N here if you're not interested in the Keystone
> DSPs or just want to use a bare minimum kernel.
>
> +config MESON_MX_AO_ARC_REMOTEPROC
> + tristate "Amlogic Meson6/8/8b/8m2 AO ARC remote processor support"
> + depends on HAS_IOMEM
> + depends on (ARM && ARCH_MESON) || COMPILE_TEST
> + select GENERIC_ALLOCATOR
> + help
> + Say m or y here to have support for the AO ARC remote processor
> + on Amlogic Meson6/Meson8/Meson8b/Meson8m2 SoCs. This is
> + typically used for system suspend.
> + If unsure say N.
> +
> config PRU_REMOTEPROC
> tristate "TI PRU remoteproc support"
> depends on TI_PRUSS
> diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
> index bb26c9e4ef9c..ce1abeb30907 100644
> --- a/drivers/remoteproc/Makefile
> +++ b/drivers/remoteproc/Makefile
> @@ -18,6 +18,7 @@ obj-$(CONFIG_OMAP_REMOTEPROC) += omap_remoteproc.o
> obj-$(CONFIG_WKUP_M3_RPROC) += wkup_m3_rproc.o
> obj-$(CONFIG_DA8XX_REMOTEPROC) += da8xx_remoteproc.o
> obj-$(CONFIG_KEYSTONE_REMOTEPROC) += keystone_remoteproc.o
> +obj-$(CONFIG_MESON_MX_AO_ARC_REMOTEPROC)+= meson_mx_ao_arc.o
> obj-$(CONFIG_PRU_REMOTEPROC) += pru_rproc.o
> obj-$(CONFIG_QCOM_PIL_INFO) += qcom_pil_info.o
> obj-$(CONFIG_QCOM_RPROC_COMMON) += qcom_common.o
> diff --git a/drivers/remoteproc/meson_mx_ao_arc.c b/drivers/remoteproc/meson_mx_ao_arc.c
> new file mode 100644
> index 000000000000..ea9db46a7e03
> --- /dev/null
> +++ b/drivers/remoteproc/meson_mx_ao_arc.c
> @@ -0,0 +1,261 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Copyright (C) 2020 Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> + */
> +
> +#include <linux/bitfield.h>
> +#include <linux/bitops.h>
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/property.h>
I moved this just above platform_device.h and applied this set.
Thanks,
Mathieu
> +#include <linux/genalloc.h>
> +#include <linux/io.h>
> +#include <linux/mfd/syscon.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/remoteproc.h>
> +#include <linux/reset.h>
> +#include <linux/sizes.h>
> +
> +#include "remoteproc_internal.h"
> +
> +#define AO_REMAP_REG0 0x0
> +#define AO_REMAP_REG0_REMAP_AHB_SRAM_BITS_17_14_FOR_ARM_CPU GENMASK(3, 0)
> +
> +#define AO_REMAP_REG1 0x4
> +#define AO_REMAP_REG1_MOVE_AHB_SRAM_TO_0X0_INSTEAD_OF_DDR BIT(4)
> +#define AO_REMAP_REG1_REMAP_AHB_SRAM_BITS_17_14_FOR_MEDIA_CPU GENMASK(3, 0)
> +
> +#define AO_CPU_CNTL 0x0
> +#define AO_CPU_CNTL_AHB_SRAM_BITS_31_20 GENMASK(28, 16)
> +#define AO_CPU_CNTL_HALT BIT(9)
> +#define AO_CPU_CNTL_UNKNONWN BIT(8)
> +#define AO_CPU_CNTL_RUN BIT(0)
> +
> +#define AO_CPU_STAT 0x4
> +
> +#define AO_SECURE_REG0 0x0
> +#define AO_SECURE_REG0_AHB_SRAM_BITS_19_12 GENMASK(15, 8)
> +
> +/* Only bits [31:20] and [17:14] are usable, all other bits must be zero */
> +#define MESON_AO_RPROC_SRAM_USABLE_BITS 0xfff3c000
> +
> +#define MESON_AO_RPROC_MEMORY_OFFSET 0x10000000
> +
> +struct meson_mx_ao_arc_rproc_priv {
> + void __iomem *remap_base;
> + void __iomem *cpu_base;
> + unsigned long sram_va;
> + phys_addr_t sram_pa;
> + size_t sram_size;
> + struct gen_pool *sram_pool;
> + struct reset_control *arc_reset;
> + struct clk *arc_pclk;
> + struct regmap *secbus2_regmap;
> +};
> +
> +static int meson_mx_ao_arc_rproc_start(struct rproc *rproc)
> +{
> + struct meson_mx_ao_arc_rproc_priv *priv = rproc->priv;
> + phys_addr_t translated_sram_addr;
> + u32 tmp;
> + int ret;
> +
> + ret = clk_prepare_enable(priv->arc_pclk);
> + if (ret)
> + return ret;
> +
> + tmp = FIELD_PREP(AO_REMAP_REG0_REMAP_AHB_SRAM_BITS_17_14_FOR_ARM_CPU,
> + priv->sram_pa >> 14);
> + writel(tmp, priv->remap_base + AO_REMAP_REG0);
> +
> + /*
> + * The SRAM content as seen by the ARC core always starts at 0x0
> + * regardless of the value given here (this was discovered by trial and
> + * error). For SoCs older than Meson6 we probably have to set
> + * AO_REMAP_REG1_MOVE_AHB_SRAM_TO_0X0_INSTEAD_OF_DDR to achieve the
> + * same. (At least) For Meson8 and newer that bit must not be set.
> + */
> + writel(0x0, priv->remap_base + AO_REMAP_REG1);
> +
> + regmap_update_bits(priv->secbus2_regmap, AO_SECURE_REG0,
> + AO_SECURE_REG0_AHB_SRAM_BITS_19_12,
> + FIELD_PREP(AO_SECURE_REG0_AHB_SRAM_BITS_19_12,
> + priv->sram_pa >> 12));
> +
> + ret = reset_control_reset(priv->arc_reset);
> + if (ret) {
> + clk_disable_unprepare(priv->arc_pclk);
> + return ret;
> + }
> +
> + usleep_range(10, 100);
> +
> + /*
> + * Convert from 0xd9000000 to 0xc9000000 as the vendor driver does.
> + * This only seems to be relevant for the AO_CPU_CNTL register. It is
> + * unknown why this is needed.
> + */
> + translated_sram_addr = priv->sram_pa - MESON_AO_RPROC_MEMORY_OFFSET;
> +
> + tmp = FIELD_PREP(AO_CPU_CNTL_AHB_SRAM_BITS_31_20,
> + translated_sram_addr >> 20);
> + tmp |= AO_CPU_CNTL_UNKNONWN | AO_CPU_CNTL_RUN;
> + writel(tmp, priv->cpu_base + AO_CPU_CNTL);
> +
> + usleep_range(20, 200);
> +
> + return 0;
> +}
> +
> +static int meson_mx_ao_arc_rproc_stop(struct rproc *rproc)
> +{
> + struct meson_mx_ao_arc_rproc_priv *priv = rproc->priv;
> +
> + writel(AO_CPU_CNTL_HALT, priv->cpu_base + AO_CPU_CNTL);
> +
> + clk_disable_unprepare(priv->arc_pclk);
> +
> + return 0;
> +}
> +
> +static void *meson_mx_ao_arc_rproc_da_to_va(struct rproc *rproc, u64 da,
> + size_t len, bool *is_iomem)
> +{
> + struct meson_mx_ao_arc_rproc_priv *priv = rproc->priv;
> +
> + /* The memory from the ARC core's perspective always starts at 0x0. */
> + if ((da + len) > priv->sram_size)
> + return NULL;
> +
> + return (void *)priv->sram_va + da;
> +}
> +
> +static struct rproc_ops meson_mx_ao_arc_rproc_ops = {
> + .start = meson_mx_ao_arc_rproc_start,
> + .stop = meson_mx_ao_arc_rproc_stop,
> + .da_to_va = meson_mx_ao_arc_rproc_da_to_va,
> + .get_boot_addr = rproc_elf_get_boot_addr,
> + .load = rproc_elf_load_segments,
> + .sanity_check = rproc_elf_sanity_check,
> +};
> +
> +static int meson_mx_ao_arc_rproc_probe(struct platform_device *pdev)
> +{
> + struct meson_mx_ao_arc_rproc_priv *priv;
> + struct device *dev = &pdev->dev;
> + const char *fw_name = NULL;
> + struct rproc *rproc;
> + int ret;
> +
> + device_property_read_string(dev, "firmware-name", &fw_name);
> +
> + rproc = devm_rproc_alloc(dev, "meson-mx-ao-arc",
> + &meson_mx_ao_arc_rproc_ops, fw_name,
> + sizeof(*priv));
> + if (!rproc)
> + return -ENOMEM;
> +
> + rproc->has_iommu = false;
> + priv = rproc->priv;
> +
> + priv->sram_pool = of_gen_pool_get(dev->of_node, "sram", 0);
> + if (!priv->sram_pool) {
> + dev_err(dev, "Could not get SRAM pool\n");
> + return -ENODEV;
> + }
> +
> + priv->sram_size = gen_pool_avail(priv->sram_pool);
> +
> + priv->sram_va = gen_pool_alloc(priv->sram_pool, priv->sram_size);
> + if (!priv->sram_va) {
> + dev_err(dev, "Could not alloc memory in SRAM pool\n");
> + return -ENOMEM;
> + }
> +
> + priv->sram_pa = gen_pool_virt_to_phys(priv->sram_pool, priv->sram_va);
> + if (priv->sram_pa & ~MESON_AO_RPROC_SRAM_USABLE_BITS) {
> + dev_err(dev, "SRAM address contains unusable bits\n");
> + ret = -EINVAL;
> + goto err_free_genpool;
> + }
> +
> + priv->secbus2_regmap = syscon_regmap_lookup_by_phandle(dev->of_node,
> + "amlogic,secbus2");
> + if (IS_ERR(priv->secbus2_regmap)) {
> + dev_err(dev, "Failed to find SECBUS2 regmap\n");
> + ret = PTR_ERR(priv->secbus2_regmap);
> + goto err_free_genpool;
> + }
> +
> + priv->remap_base = devm_platform_ioremap_resource_byname(pdev, "remap");
> + if (IS_ERR(priv->remap_base)) {
> + ret = PTR_ERR(priv->remap_base);
> + goto err_free_genpool;
> + }
> +
> + priv->cpu_base = devm_platform_ioremap_resource_byname(pdev, "cpu");
> + if (IS_ERR(priv->cpu_base)) {
> + ret = PTR_ERR(priv->cpu_base);
> + goto err_free_genpool;
> + }
> +
> + priv->arc_reset = devm_reset_control_get_exclusive(dev, NULL);
> + if (IS_ERR(priv->arc_reset)) {
> + dev_err(dev, "Failed to get ARC reset\n");
> + ret = PTR_ERR(priv->arc_reset);
> + goto err_free_genpool;
> + }
> +
> + priv->arc_pclk = devm_clk_get(dev, NULL);
> + if (IS_ERR(priv->arc_pclk)) {
> + dev_err(dev, "Failed to get the ARC PCLK\n");
> + ret = PTR_ERR(priv->arc_pclk);
> + goto err_free_genpool;
> + }
> +
> + platform_set_drvdata(pdev, rproc);
> +
> + ret = rproc_add(rproc);
> + if (ret)
> + goto err_free_genpool;
> +
> + return 0;
> +
> +err_free_genpool:
> + gen_pool_free(priv->sram_pool, priv->sram_va, priv->sram_size);
> + return ret;
> +}
> +
> +static int meson_mx_ao_arc_rproc_remove(struct platform_device *pdev)
> +{
> + struct rproc *rproc = platform_get_drvdata(pdev);
> + struct meson_mx_ao_arc_rproc_priv *priv = rproc->priv;
> +
> + rproc_del(rproc);
> + gen_pool_free(priv->sram_pool, priv->sram_va, priv->sram_size);
> +
> + return 0;
> +}
> +
> +static const struct of_device_id meson_mx_ao_arc_rproc_match[] = {
> + { .compatible = "amlogic,meson8-ao-arc" },
> + { .compatible = "amlogic,meson8b-ao-arc" },
> + { /* sentinel */ }
> +};
> +MODULE_DEVICE_TABLE(of, meson_mx_ao_arc_rproc_match);
> +
> +static struct platform_driver meson_mx_ao_arc_rproc_driver = {
> + .probe = meson_mx_ao_arc_rproc_probe,
> + .remove = meson_mx_ao_arc_rproc_remove,
> + .driver = {
> + .name = "meson-mx-ao-arc-rproc",
> + .of_match_table = meson_mx_ao_arc_rproc_match,
> + },
> +};
> +module_platform_driver(meson_mx_ao_arc_rproc_driver);
> +
> +MODULE_DESCRIPTION("Amlogic Meson6/8/8b/8m2 AO ARC remote processor driver");
> +MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl at googlemail.com>");
> +MODULE_LICENSE("GPL v2");
> --
> 2.33.0
>
More information about the linux-arm-kernel
mailing list