[PATCH 1/4] firmware: xilinx: Add OSPI Mux selection support

[Michal Simek]

On 9/24/21 1:36 PM, Greg Kroah-Hartman wrote:
> On Fri, Sep 24, 2021 at 03:37:08PM +0530, Sai Krishna Potthuri wrote:
>> Add OSPI Mux selection API support to select the AXI interface to OSPI.
>>
>> Signed-off-by: Sai Krishna Potthuri <lakshmi.sai.krishna.potthuri at xilinx.com>
>> ---
>>  drivers/firmware/xilinx/zynqmp.c     | 17 +++++++++++++++++
>>  include/linux/firmware/xlnx-zynqmp.h | 12 ++++++++++++
>>  2 files changed, 29 insertions(+)
>>
>> diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c
>> index 15b138326ecc..43c3b5a9eef7 100644
>> --- a/drivers/firmware/xilinx/zynqmp.c
>> +++ b/drivers/firmware/xilinx/zynqmp.c
>> @@ -647,6 +647,23 @@ int zynqmp_pm_sd_dll_reset(u32 node_id, u32 type)
>>  }
>>  EXPORT_SYMBOL_GPL(zynqmp_pm_sd_dll_reset);
>>  
>> +/**
>> + * zynqmp_pm_ospi_mux_select() - OSPI Mux selection
>> + *
>> + * @dev_id:	Device Id of the OSPI device.
>> + * @select:	OSPI Mux select value.
>> + *
>> + * This function select the OSPI Mux.
>> + *
>> + * Return:	Returns status, either success or error+reason
>> + */
>> +int zynqmp_pm_ospi_mux_select(u32 dev_id, u32 select)
>> +{
>> +	return zynqmp_pm_invoke_fn(PM_IOCTL, dev_id, IOCTL_OSPI_MUX_SELECT,
>> +				   select, 0, NULL);
>> +}
>> +EXPORT_SYMBOL_GPL(zynqmp_pm_ospi_mux_select);
>> +
>>  /**
>>   * zynqmp_pm_write_ggs() - PM API for writing global general storage (ggs)
>>   * @index:	GGS register index
>> diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h
>> index 9d1a5c175065..6979a79f553a 100644
>> --- a/include/linux/firmware/xlnx-zynqmp.h
>> +++ b/include/linux/firmware/xlnx-zynqmp.h
>> @@ -119,6 +119,7 @@ enum pm_ioctl_id {
>>  	IOCTL_READ_PGGS = 15,
>>  	/* Set healthy bit value */
>>  	IOCTL_SET_BOOT_HEALTH_STATUS = 17,
>> +	IOCTL_OSPI_MUX_SELECT = 21,
> 
> Why the gap?  What are the commands in the middle for?

Below is the full list. Not everything has been upstream yet. There was
an attempt on AFI which one colleague is working on and should send new
version soon. I don't think anybody has started with upstreaming probe
counters.
Every part has different owner with unfortunately own upstreaming plan.

Thanks,
Michal

enum pm_ioctl_id {
	IOCTL_GET_RPU_OPER_MODE = 0,
	IOCTL_SET_RPU_OPER_MODE = 1,
	IOCTL_RPU_BOOT_ADDR_CONFIG = 2,
	IOCTL_TCM_COMB_CONFIG = 3,
	IOCTL_SET_TAPDELAY_BYPASS = 4,
	IOCTL_SET_SGMII_MODE = 5,
	IOCTL_SD_DLL_RESET = 6,
	IOCTL_SET_SD_TAPDELAY = 7,
	IOCTL_SET_PLL_FRAC_MODE = 8,
	IOCTL_GET_PLL_FRAC_MODE = 9,
	IOCTL_SET_PLL_FRAC_DATA = 10,
	IOCTL_GET_PLL_FRAC_DATA = 11,
	IOCTL_WRITE_GGS = 12,
	IOCTL_READ_GGS = 13,
	IOCTL_WRITE_PGGS = 14,
	IOCTL_READ_PGGS = 15,
	/* IOCTL for ULPI reset */
	IOCTL_ULPI_RESET = 16,
	/* Set healthy bit value */
	IOCTL_SET_BOOT_HEALTH_STATUS = 17,
	IOCTL_AFI = 18,
	/* Probe counter read/write */
	IOCTL_PROBE_COUNTER_READ = 19,
	IOCTL_PROBE_COUNTER_WRITE = 20,
	IOCTL_OSPI_MUX_SELECT = 21,
	/* IOCTL for USB power request */
	IOCTL_USB_SET_STATE = 22,
	/* IOCTL to get last reset reason */
	IOCTL_GET_LAST_RESET_REASON = 23,
	/* AI engine NPI ISR clear */
	IOCTL_AIE_ISR_CLEAR = 24,
	/* Register SGI to ATF */
	IOCTL_REGISTER_SGI = 25,
	/* Runtime feature configuration */
	IOCTL_SET_FEATURE_CONFIG = 26,
	IOCTL_GET_FEATURE_CONFIG = 27,
};