[PATCH v2 2/3] ARM: dts: imx7-tqma7: add SPI-NOR flash

[Matthias Schiffer]

The SPI-NOR flash on the SoM was missing from the device tree.

The TQMa7 as a designated QSPI_RESET# pin, however depending on the
hardware configuration the pin may be unconnected, or be used for a
different purpose. With this in mind, we mux the pin as a pullup and
define an input hog for it, but keep it a separate pin group, so that it
is easy for dependent Device Trees to modify the configuration.

Signed-off-by: Matthias Schiffer <matthias.schiffer at ew.tq-group.com>
---

v2: - Add input hog for reset pin and move to separate pin group,
      explain in commit message.
    - Update flash node for modern "partitions" specification


 arch/arm/boot/dts/imx7-tqma7.dtsi | 43 +++++++++++++++++++++++++++++++
 1 file changed, 43 insertions(+)

diff --git a/arch/arm/boot/dts/imx7-tqma7.dtsi b/arch/arm/boot/dts/imx7-tqma7.dtsi
index 065e1668e280..fe42b0a46831 100644
--- a/arch/arm/boot/dts/imx7-tqma7.dtsi
+++ b/arch/arm/boot/dts/imx7-tqma7.dtsi
@@ -19,6 +19,16 @@
 	cpu-supply = <&sw1a_reg>;
 };
 
+&gpio2 {
+	/* Configured as pullup by QSPI pin group */
+	qspi-reset-hog {
+		gpio-hog;
+		gpios = <4 GPIO_ACTIVE_LOW>;
+		input;
+		line-name = "qspi-reset";
+	};
+};
+
 &i2c1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_i2c1>;
@@ -160,6 +170,25 @@
 		>;
 	};
 
+	pinctrl_qspi: qspigrp {
+		fsl,pins = <
+			MX7D_PAD_EPDC_DATA00__QSPI_A_DATA0	0x5A
+			MX7D_PAD_EPDC_DATA01__QSPI_A_DATA1	0x5A
+			MX7D_PAD_EPDC_DATA02__QSPI_A_DATA2	0x5A
+			MX7D_PAD_EPDC_DATA03__QSPI_A_DATA3	0x5A
+			MX7D_PAD_EPDC_DATA05__QSPI_A_SCLK	0x11
+			MX7D_PAD_EPDC_DATA06__QSPI_A_SS0_B	0x54
+			MX7D_PAD_EPDC_DATA07__QSPI_A_SS1_B	0x54
+		>;
+	};
+
+	pinctrl_qspi_reset: qspi_resetgrp {
+		fsl,pins = <
+			/* #QSPI_RESET */
+			MX7D_PAD_EPDC_DATA04__GPIO2_IO4		0x52
+		>;
+	};
+
 	pinctrl_usdhc3: usdhc3grp {
 		fsl,pins = <
 			MX7D_PAD_SD3_CMD__SD3_CMD		0x59
@@ -217,6 +246,20 @@
 	};
 };
 
+&qspi {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_qspi &pinctrl_qspi_reset>;
+	status = "okay";
+
+	flash0: flash at 0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <29000000>;
+		spi-rx-bus-width = <4>;
+		spi-tx-bus-width = <4>;
+	};
+};
+
 &sdma {
 	status = "okay";
 };
-- 
2.17.1