[PATCH v4 1/4] dt-bindings: mfd: aspeed-lpc: Convert to YAML schema
Rob Herring
robh+dt at kernel.org
Tue Sep 14 05:28:03 PDT 2021
On Mon, Sep 13, 2021 at 1:02 AM Chia-Wei Wang
<chiawei_wang at aspeedtech.com> wrote:
>
> Convert the bindings of Aspeed LPC from text file into YAML schema.
>
> Signed-off-by: Chia-Wei Wang <chiawei_wang at aspeedtech.com>
> ---
> .../devicetree/bindings/mfd/aspeed-lpc.txt | 157 ---------------
> .../devicetree/bindings/mfd/aspeed-lpc.yaml | 187 ++++++++++++++++++
> 2 files changed, 187 insertions(+), 157 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/mfd/aspeed-lpc.txt
> create mode 100644 Documentation/devicetree/bindings/mfd/aspeed-lpc.yaml
>
> diff --git a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt b/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt
> deleted file mode 100644
> index 936aa108eab4..000000000000
> --- a/Documentation/devicetree/bindings/mfd/aspeed-lpc.txt
> +++ /dev/null
> @@ -1,157 +0,0 @@
> -======================================================================
> -Device tree bindings for the Aspeed Low Pin Count (LPC) Bus Controller
> -======================================================================
> -
> -The LPC bus is a means to bridge a host CPU to a number of low-bandwidth
> -peripheral devices, replacing the use of the ISA bus in the age of PCI[0]. The
> -primary use case of the Aspeed LPC controller is as a slave on the bus
> -(typically in a Baseboard Management Controller SoC), but under certain
> -conditions it can also take the role of bus master.
> -
> -The LPC controller is represented as a multi-function device to account for the
> -mix of functionality, which includes, but is not limited to:
> -
> -* An IPMI Block Transfer[2] Controller
> -
> -* An LPC Host Controller: Manages LPC functions such as host vs slave mode, the
> - physical properties of some LPC pins, configuration of serial IRQs, and
> - APB-to-LPC bridging amonst other functions.
> -
> -* An LPC Host Interface Controller: Manages functions exposed to the host such
> - as LPC firmware hub cycles, configuration of the LPC-to-AHB mapping, UART
> - management and bus snoop configuration.
> -
> -* A set of SuperIO[3] scratch registers: Enables implementation of e.g. custom
> - hardware management protocols for handover between the host and baseboard
> - management controller.
> -
> -Additionally the state of the LPC controller influences the pinmux
> -configuration, therefore the host portion of the controller is exposed as a
> -syscon as a means to arbitrate access.
> -
> -[0] http://www.intel.com/design/chipsets/industry/25128901.pdf
> -[1] https://www.renesas.com/en-sg/doc/products/mpumcu/001/rej09b0078_h8s2168.pdf?key=7c88837454702128622bee53acbda8f4
> -[2] https://www.intel.com/content/dam/www/public/us/en/documents/product-briefs/ipmi-second-gen-interface-spec-v2-rev1-1.pdf
> -[3] https://en.wikipedia.org/wiki/Super_I/O
> -
> -Required properties
> -===================
> -
> -- compatible: One of:
> - "aspeed,ast2400-lpc-v2", "simple-mfd", "syscon"
> - "aspeed,ast2500-lpc-v2", "simple-mfd", "syscon"
> - "aspeed,ast2600-lpc-v2", "simple-mfd", "syscon"
> -
> -- reg: contains the physical address and length values of the Aspeed
> - LPC memory region.
> -
> -- #address-cells: <1>
> -- #size-cells: <1>
> -- ranges: Maps 0 to the physical address and length of the LPC memory
> - region
> -
> -Example:
> -
> -lpc: lpc at 1e789000 {
> - compatible = "aspeed,ast2500-lpc-v2", "simple-mfd", "syscon";
> - reg = <0x1e789000 0x1000>;
> -
> - #address-cells = <1>;
> - #size-cells = <1>;
> - ranges = <0x0 0x1e789000 0x1000>;
> -
> - lpc_snoop: lpc-snoop at 0 {
> - compatible = "aspeed,ast2600-lpc-snoop";
> - reg = <0x0 0x80>;
> - interrupts = <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>;
> - snoop-ports = <0x80>;
> - };
> -};
> -
> -
> -LPC Host Interface Controller
> --------------------
> -
> -The LPC Host Interface Controller manages functions exposed to the host such as
> -LPC firmware hub cycles, configuration of the LPC-to-AHB mapping, UART
> -management and bus snoop configuration.
> -
> -Required properties:
> -
> -- compatible: One of:
> - "aspeed,ast2400-lpc-ctrl";
> - "aspeed,ast2500-lpc-ctrl";
> - "aspeed,ast2600-lpc-ctrl";
> -
> -- reg: contains offset/length values of the host interface controller
> - memory regions
> -
> -- clocks: contains a phandle to the syscon node describing the clocks.
> - There should then be one cell representing the clock to use
> -
> -Optional properties:
> -
> -- memory-region: A phandle to a reserved_memory region to be used for the LPC
> - to AHB mapping
> -
> -- flash: A phandle to the SPI flash controller containing the flash to
> - be exposed over the LPC to AHB mapping
> -
> -Example:
> -
> -lpc_ctrl: lpc-ctrl at 80 {
> - compatible = "aspeed,ast2500-lpc-ctrl";
> - reg = <0x80 0x80>;
> - clocks = <&syscon ASPEED_CLK_GATE_LCLK>;
> - memory-region = <&flash_memory>;
> - flash = <&spi>;
> -};
> -
> -LPC Host Controller
> --------------------
> -
> -The Aspeed LPC Host Controller configures the Low Pin Count (LPC) bus behaviour
> -between the host and the baseboard management controller. The registers exist
> -in the "host" portion of the Aspeed LPC controller, which must be the parent of
> -the LPC host controller node.
> -
> -Required properties:
> -
> -- compatible: One of:
> - "aspeed,ast2400-lhc";
> - "aspeed,ast2500-lhc";
> - "aspeed,ast2600-lhc";
> -
> -- reg: contains offset/length values of the LHC memory regions. In the
> - AST2400 and AST2500 there are two regions.
> -
> -Example:
> -
> -lhc: lhc at a0 {
> - compatible = "aspeed,ast2500-lhc";
> - reg = <0xa0 0x24 0xc8 0x8>;
> -};
> -
> -LPC reset control
> ------------------
> -
> -The UARTs present in the ASPEED SoC can have their resets tied to the reset
> -state of the LPC bus. Some systems may chose to modify this configuration.
> -
> -Required properties:
> -
> - - compatible: One of:
> - "aspeed,ast2600-lpc-reset";
> - "aspeed,ast2500-lpc-reset";
> - "aspeed,ast2400-lpc-reset";
> -
> - - reg: offset and length of the IP in the LHC memory region
> - - #reset-controller indicates the number of reset cells expected
> -
> -Example:
> -
> -lpc_reset: reset-controller at 98 {
> - compatible = "aspeed,ast2500-lpc-reset";
> - reg = <0x98 0x4>;
> - #reset-cells = <1>;
> -};
> diff --git a/Documentation/devicetree/bindings/mfd/aspeed-lpc.yaml b/Documentation/devicetree/bindings/mfd/aspeed-lpc.yaml
> new file mode 100644
> index 000000000000..4e3862cf2a4b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/aspeed-lpc.yaml
> @@ -0,0 +1,187 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +# # Copyright (c) 2021 Aspeed Tehchnology Inc.
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/aspeed-lpc.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Aspeed Low Pin Count (LPC) Bus Controller
> +
> +maintainers:
> + - Andrew Jeffery <andrew at aj.id.au>
> + - Chia-Wei Wang <chiawei_wang at aspeedtech.com>
> +
> +description:
> + The LPC bus is a means to bridge a host CPU to a number of low-bandwidth
> + peripheral devices, replacing the use of the ISA bus in the age of PCI[0]. The
> + primary use case of the Aspeed LPC controller is as a slave on the bus
> + (typically in a Baseboard Management Controller SoC), but under certain
> + conditions it can also take the role of bus master.
> +
> + The LPC controller is represented as a multi-function device to account for the
> + mix of functionality, which includes, but is not limited to
> +
> + * An IPMI Block Transfer[2] Controller
> +
> + * An LPC Host Interface Controller manages functions exposed to the host such
> + as LPC firmware hub cycles, configuration of the LPC-to-AHB mapping, UART
> + management and bus snoop configuration.
> +
> + * A set of SuperIO[3] scratch registers enableing implementation of e.g. custom
> + hardware management protocols for handover between the host and baseboard
> + management controller.
> +
> + Additionally the state of the LPC controller influences the pinmux
> + configuration, therefore the host portion of the controller is exposed as a
> + syscon as a means to arbitrate access.
> +
> +properties:
> + compatible:
> + items:
> + - enum:
> + - aspeed,ast2400-lpc-v2
> + - aspeed,ast2500-lpc-v2
> + - aspeed,ast2600-lpc-v2
> + - const: simple-mfd
> + - const: syscon
> +
> + reg:
> + maxItems: 1
> +
> + "#address-cells":
> + const: 1
> +
> + "#size-cells":
> + const: 1
> +
> + ranges: true
> +
> +patternProperties:
> + "^lpc-ctrl@[0-9a-f]+$":
> + type: object
> +
> + description:
> + The LPC Host Interface Controller manages functions exposed to the host such as
> + LPC firmware hub cycles, configuration of the LPC-to-AHB mapping, UART management
> + and bus snoop configuration.
> +
> + properties:
> + comptabile:
typo here. This is the source of your warnings.
Rob
More information about the linux-arm-kernel
mailing list