[PATCH AUTOSEL 5.14 203/252] mmc: sdhci-of-arasan: Modified SD default speed to 19MHz for ZynqMP

Sasha Levin sashal at kernel.org
Thu Sep 9 04:40:17 PDT 2021


From: Manish Narani <manish.narani at xilinx.com>

[ Upstream commit c0b4e411a9b09748466ee06d2ae6772effa64dfb ]

SD standard speed timing was met only at 19MHz and not 25 MHz, that's
why changing driver to 19MHz. The reason for this is when a level shifter
is used on the board, timing was met for standard speed only at 19MHz.
Since this level shifter is commonly required for high speed modes,
the driver is modified to use standard speed of 19Mhz.

Signed-off-by: Manish Narani <manish.narani at xilinx.com>
Acked-by: Adrian Hunter <adrian.hunter at intel.com>
Link: https://lore.kernel.org/r/1623753837-21035-2-git-send-email-manish.narani@xilinx.com
Signed-off-by: Ulf Hansson <ulf.hansson at linaro.org>
Signed-off-by: Sasha Levin <sashal at kernel.org>
---
 drivers/mmc/host/sdhci-of-arasan.c | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/drivers/mmc/host/sdhci-of-arasan.c b/drivers/mmc/host/sdhci-of-arasan.c
index 0e7c07ed9690..03c80c9bb7e3 100644
--- a/drivers/mmc/host/sdhci-of-arasan.c
+++ b/drivers/mmc/host/sdhci-of-arasan.c
@@ -159,6 +159,12 @@ struct sdhci_arasan_data {
 /* Controller immediately reports SDHCI_CLOCK_INT_STABLE after enabling the
  * internal clock even when the clock isn't stable */
 #define SDHCI_ARASAN_QUIRK_CLOCK_UNSTABLE BIT(1)
+/*
+ * Some of the Arasan variations might not have timing requirements
+ * met at 25MHz for Default Speed mode, those controllers work at
+ * 19MHz instead
+ */
+#define SDHCI_ARASAN_QUIRK_CLOCK_25_BROKEN BIT(2)
 };
 
 struct sdhci_arasan_of_data {
@@ -290,6 +296,16 @@ static void sdhci_arasan_set_clock(struct sdhci_host *host, unsigned int clock)
 		sdhci_arasan->is_phy_on = false;
 	}
 
+	if (sdhci_arasan->quirks & SDHCI_ARASAN_QUIRK_CLOCK_25_BROKEN) {
+		/*
+		 * Some of the Arasan variations might not have timing
+		 * requirements met at 25MHz for Default Speed mode,
+		 * those controllers work at 19MHz instead.
+		 */
+		if (clock == DEFAULT_SPEED_MAX_DTR)
+			clock = (DEFAULT_SPEED_MAX_DTR * 19) / 25;
+	}
+
 	/* Set the Input and Output Clock Phase Delays */
 	if (clk_data->set_clk_delays)
 		clk_data->set_clk_delays(host);
@@ -1608,6 +1624,8 @@ static int sdhci_arasan_probe(struct platform_device *pdev)
 	if (of_device_is_compatible(np, "xlnx,zynqmp-8.9a")) {
 		host->mmc_host_ops.execute_tuning =
 			arasan_zynqmp_execute_tuning;
+
+		sdhci_arasan->quirks |= SDHCI_ARASAN_QUIRK_CLOCK_25_BROKEN;
 	}
 
 	arasan_dt_parse_clk_phases(dev, &sdhci_arasan->clk_data);
-- 
2.30.2




More information about the linux-arm-kernel mailing list