[v4] PCI: Avoid unsync of LTR mechanism configuration
mingchuang qiao
mingchuang.qiao at mediatek.com
Sun Sep 5 22:36:14 PDT 2021
Hi Bjorn,
On Thu, 2021-02-18 at 10:50 -0600, Bjorn Helgaas wrote:
> On Thu, Feb 04, 2021 at 05:51:25PM +0800, mingchuang.qiao at mediatek.co
> m wrote:
> > From: Mingchuang Qiao <mingchuang.qiao at mediatek.com>
> >
> > In bus scan flow, the "LTR Mechanism Enable" bit of DEVCTL2
> > register is
> > configured in pci_configure_ltr(). If device and bridge both
> > support LTR
> > mechanism, the "LTR Mechanism Enable" bit of device and bridge will
> > be
> > enabled in DEVCTL2 register. And pci_dev->ltr_path will be set as
> > 1.
> >
> > If PCIe link goes down when device resets, the "LTR Mechanism
> > Enable" bit
> > of bridge will change to 0 according to PCIe r5.0, sec 7.5.3.16.
> > However,
> > the pci_dev->ltr_path value of bridge is still 1.
> >
> > For following conditions, check and re-configure "LTR Mechanism
> > Enable" bit
> > of bridge to make "LTR Mechanism Enable" bit match ltr_path value.
> > -before configuring device's LTR for hot-remove/hot-add
> > -before restoring device's DEVCTL2 register when restore device
> > state
>
> There's definitely a bug here. The commit log should say a little
> more about what it is. I *think* if LTR is enabled and we suspend
> (putting the device in D3cold) and resume, LTR probably doesn't work
> after resume because LTR is disabled in the upstream bridge, which
> would be an obvious bug.
>
> Also, if a device with LTR enabled is hot-removed, and we hot-add a
> device, I think LTR will not work on the new device. Possibly also a
> bug, although I'm not convinced we know how to configure LTR on the
> new device anyway.
>
> So I'd *like* to merge the bug fix for v5.12, but I think I'll wait
> because of the issue below.
>
A friendly ping.
Any further process shall I make to get this patch merged?
> > Signed-off-by: Mingchuang Qiao <mingchuang.qiao at mediatek.com>
> > ---
> > changes of v4
> > -fix typo of commit message
> > -rename: pci_reconfigure_bridge_ltr()-
> > >pci_bridge_reconfigure_ltr()
> > changes of v3
> > -call pci_reconfigure_bridge_ltr() in probe.c
> > changes of v2
> > -modify patch description
> > -reconfigure bridge's LTR before restoring device DEVCTL2 register
> > ---
> > drivers/pci/pci.c | 25 +++++++++++++++++++++++++
> > drivers/pci/pci.h | 1 +
> > drivers/pci/probe.c | 13 ++++++++++---
> > 3 files changed, 36 insertions(+), 3 deletions(-)
> >
> > diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
> > index b9fecc25d213..6bf65d295331 100644
> > --- a/drivers/pci/pci.c
> > +++ b/drivers/pci/pci.c
> > @@ -1437,6 +1437,24 @@ static int pci_save_pcie_state(struct
> > pci_dev *dev)
> > return 0;
> > }
> >
> > +void pci_bridge_reconfigure_ltr(struct pci_dev *dev)
> > +{
> > +#ifdef CONFIG_PCIEASPM
> > + struct pci_dev *bridge;
> > + u32 ctl;
> > +
> > + bridge = pci_upstream_bridge(dev);
> > + if (bridge && bridge->ltr_path) {
> > + pcie_capability_read_dword(bridge,
> > PCI_EXP_DEVCTL2, &ctl);
> > + if (!(ctl & PCI_EXP_DEVCTL2_LTR_EN)) {
> > + pci_dbg(bridge, "re-enabling LTR\n");
> > + pcie_capability_set_word(bridge,
> > PCI_EXP_DEVCTL2,
> > + PCI_EXP_DEVCTL2_L
> > TR_EN);
>
> This pattern of updating the upstream bridge on behalf of "dev" is
> problematic because it's racy:
>
> CPU 1 CPU 2
> ------------------- ---------------------
> ctl = read DEVCTL2 ctl = read(DEVCTL2)
> ctl |= DEVCTL2_LTR_EN ctl |= DEVCTL2_ARI
> write(DEVCTL2, ctl)
> write(DEVCTL2, ctl)
>
> Now the bridge has ARI set, but not LTR_EN.
>
> We have the same problem in the pci_enable_device() path. The most
> recent try at fixing it is [1].
>
> [1] https://lore.kernel.org/linux-pci/20201218174011.340514-2-s.miros
> hnichenko at yadro.com/
>
> > + }
> > + }
> > +#endif
> > +}
> > +
> > static void pci_restore_pcie_state(struct pci_dev *dev)
> > {
> > int i = 0;
> > @@ -1447,6 +1465,13 @@ static void pci_restore_pcie_state(struct
> > pci_dev *dev)
> > if (!save_state)
> > return;
> >
> > + /*
> > + * Downstream ports reset the LTR enable bit when link
> > goes down.
> > + * Check and re-configure the bit here before restoring
> > device.
> > + * PCIe r5.0, sec 7.5.3.16.
> > + */
> > + pci_bridge_reconfigure_ltr(dev);
> > +
> > cap = (u16 *)&save_state->cap.data[0];
> > pcie_capability_write_word(dev, PCI_EXP_DEVCTL, cap[i++]);
> > pcie_capability_write_word(dev, PCI_EXP_LNKCTL, cap[i++]);
> > diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
> > index 5c59365092fa..b3a5e5287cb7 100644
> > --- a/drivers/pci/pci.h
> > +++ b/drivers/pci/pci.h
> > @@ -111,6 +111,7 @@ void pci_free_cap_save_buffers(struct pci_dev
> > *dev);
> > bool pci_bridge_d3_possible(struct pci_dev *dev);
> > void pci_bridge_d3_update(struct pci_dev *dev);
> > void pci_bridge_wait_for_secondary_bus(struct pci_dev *dev);
> > +void pci_bridge_reconfigure_ltr(struct pci_dev *dev);
> >
> > static inline void pci_wakeup_event(struct pci_dev *dev)
> > {
> > diff --git a/drivers/pci/probe.c b/drivers/pci/probe.c
> > index 953f15abc850..ade055e9fb58 100644
> > --- a/drivers/pci/probe.c
> > +++ b/drivers/pci/probe.c
> > @@ -2132,9 +2132,16 @@ static void pci_configure_ltr(struct pci_dev
> > *dev)
> > * Complex and all intermediate Switches indicate support
> > for LTR.
> > * PCIe r4.0, sec 6.18.
> > */
> > - if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT ||
> > - ((bridge = pci_upstream_bridge(dev)) &&
> > - bridge->ltr_path)) {
> > + if (pci_pcie_type(dev) == PCI_EXP_TYPE_ROOT_PORT) {
> > + pcie_capability_set_word(dev, PCI_EXP_DEVCTL2,
> > + PCI_EXP_DEVCTL2_LTR_EN);
> > + dev->ltr_path = 1;
> > + return;
> > + }
> > +
> > + bridge = pci_upstream_bridge(dev);
> > + if (bridge && bridge->ltr_path) {
> > + pci_bridge_reconfigure_ltr(dev);
> > pcie_capability_set_word(dev, PCI_EXP_DEVCTL2,
> > PCI_EXP_DEVCTL2_LTR_EN);
> > dev->ltr_path = 1;
> > --
> > 2.18.0
>
> _______________________________________________
> Linux-mediatek mailing list
> Linux-mediatek at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-mediatek
More information about the linux-arm-kernel
mailing list