[PATCH] Documentation, dt, numa: Add note to empty NUMA node

[Gavin Shan]

The empty memory nodes, where no memory resides in, are allowed.
For these empty memory nodes, the 'len' of 'reg' property is zero.
The NUMA node IDs are still valid and parsed, but memory may be
added to them through hotplug afterwards. Currently, QEMU fails
to boot when multiple empty memory nodes are specified. It's
caused by device-tree population failure and duplicated memory
node names.

As device-tree specification indicates, the 'unit-address' of
these empty memory nodes, part of their names, are the equivalents
to 'base-address'. Unfortunately, I finds difficulty to get where
the assignment of 'base-address' is properly documented for these
empty memory nodes. So lets add a section for empty memory nodes
to cover this in NUMA binding document. The 'unit-address',
equivalent to 'base-address' in the 'reg' property of these empty
memory nodes is specified to be the summation of highest memory
address plus the NUMA node ID.

Signed-off-by: Gavin Shan <gshan at redhat.com>
Acked-by: Randy Dunlap <rdunlap at infradead.org>
---
 Documentation/devicetree/bindings/numa.txt | 60 +++++++++++++++++++++-
 1 file changed, 59 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/numa.txt b/Documentation/devicetree/bindings/numa.txt
index 21b35053ca5a..82f047bc8dd6 100644
--- a/Documentation/devicetree/bindings/numa.txt
+++ b/Documentation/devicetree/bindings/numa.txt
@@ -103,7 +103,65 @@ Example:
 		};
 
 ==============================================================================
-4 - Example dts
+4 - Empty memory nodes
+==============================================================================
+
+Empty memory nodes, which no memory resides in, are allowed. The 'length'
+field of the 'reg' property is zero. However, the 'base-address' is a
+dummy and invalid address, which is the summation of highest memory address
+plus the NUMA node ID. The NUMA node IDs and distance maps are still valid
+and memory may be added into them through hotplug afterwards.
+
+Example:
+
+	memory at 0 {
+		device_type = "memory";
+		reg = <0x0 0x0 0x0 0x80000000>;
+		numa-node-id = <0>;
+	};
+
+	memory at 80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x0 0x80000000>;
+		numa-node-id = <1>;
+	};
+
+	/* Empty memory node */
+	memory at 100000002 {
+		device_type = "memory";
+		reg = <0x1 0x2 0x0 0x0>;
+		numa-node-id = <2>;
+	};
+
+	/* Empty memory node */
+	memory at 100000003 {
+		device_type = "memory";
+		reg = <0x1 0x3 0x0 0x0>;
+		numa-node-id = <3>;
+	};
+
+	distance-map {
+		compatible = "numa-distance-map-v1";
+		distance-matrix = <0 0  10>,
+				  <0 1  20>,
+				  <0 2  40>,
+				  <0 3  20>,
+				  <1 0  20>,
+				  <1 1  10>,
+				  <1 2  20>,
+				  <1 3  40>,
+				  <2 0  40>,
+				  <2 1  20>,
+				  <2 2  10>,
+				  <2 3  20>,
+				  <3 0  20>,
+				  <3 1  40>,
+				  <3 2  20>,
+				  <3 3  10>;
+	};
+
+==============================================================================
+5 - Example dts
 ==============================================================================
 
 Dual socket system consists of 2 boards connected through ccn bus and
-- 
2.23.0