[PATCH v11 1/4] dt-bindings: pinctrl: mt8195: add rsel define

[Chen-Yu Tsai]

On Thu, Sep 2, 2021 at 10:54 AM zhiyong.tao <zhiyong.tao at mediatek.com> wrote:
>
> On Wed, 2021-09-01 at 12:35 +0800, Chen-Yu Tsai wrote:
> > On Mon, Aug 30, 2021 at 8:36 AM Zhiyong Tao <zhiyong.tao at mediatek.com> wrote:
> > >
> > > This patch adds rsel define for mt8195.
> > >
> > > Signed-off-by: Zhiyong Tao <zhiyong.tao at mediatek.com>
> > > ---
> > >  include/dt-bindings/pinctrl/mt65xx.h | 9 +++++++++
> > >  1 file changed, 9 insertions(+)
> > >
> > > diff --git a/include/dt-bindings/pinctrl/mt65xx.h b/include/dt-bindings/pinctrl/mt65xx.h
> > > index 7e16e58fe1f7..f5934abcd1bd 100644
> > > --- a/include/dt-bindings/pinctrl/mt65xx.h
> > > +++ b/include/dt-bindings/pinctrl/mt65xx.h
> > > @@ -16,6 +16,15 @@
> > >  #define MTK_PUPD_SET_R1R0_10 102
> > >  #define MTK_PUPD_SET_R1R0_11 103
> > >
> > > +#define MTK_PULL_SET_RSEL_000  200
> > > +#define MTK_PULL_SET_RSEL_001  201
> > > +#define MTK_PULL_SET_RSEL_010  202
> > > +#define MTK_PULL_SET_RSEL_011  203
> > > +#define MTK_PULL_SET_RSEL_100  204
> > > +#define MTK_PULL_SET_RSEL_101  205
> > > +#define MTK_PULL_SET_RSEL_110  206
> > > +#define MTK_PULL_SET_RSEL_111  207
> >
> > Could you keep the spacing between constants tighter, or have no spacing
> > at all? Like having MTK_PULL_SET_RSEL_000 defined as 104 and so on. This
> > would reduce the chance of new macro values colliding with actual resistor
> > values set in the datasheets, plus a contiguous space would be easy to
> > rule as macros.
> >
> > ChenYu
>
> Hi chenyu,
> By the current solution, it won't be mixed used by MTK_PULL_SET_RSEL_XXX
> and real  resistor value.
> If user use MTK_PULL_SET_RSEL_XXX, They don't care the define which
> means how much resistor value.

What I meant was that by keeping the value space tight, we avoid the
situation where in some new chip, one of the RSEL resistors happens to
be 200 or 300 ohms. 100 is already taken, so there's nothing we can
do if new designs actually do have 100 ohm settings.

> We think that we don't contiguous macro space for different register.
> It may increase code complexity to make having MTK_PULL_SET_RSEL_000
> defined as 104.

Can you elaborate? It is a simple range check and offset handling. Are
you concerned that a new design would have R2R1R0 and you would like
the macros to be contiguous?

BTW I don't quite get why decimal base values (100, 200, etc.) were
chosen. One would think that binary bases are easier to handle in code.


ChenYu

> Thanks.
>
> >
> > >  #define MTK_DRIVE_2mA  2
> > >  #define MTK_DRIVE_4mA  4
> > >  #define MTK_DRIVE_6mA  6
> > > --
> > > 2.18.0
> > > _______________________________________________
> > > Linux-mediatek mailing list
> > > Linux-mediatek at lists.infradead.org
> > > http://lists.infradead.org/mailman/listinfo/linux-mediatek
>