[PATCH 2/2 v2] ARM: ixp4xx: Delete the Goramo MLR boardfile
Linus Walleij
linus.walleij at linaro.org
Mon Nov 29 15:13:07 PST 2021
This board is replaced with the corresponding device tree.
Cc: Krzysztof Hałasa <khalasa at piap.pl>
Signed-off-by: Linus Walleij <linus.walleij at linaro.org>
---
ChangeLog v1->v2:
- New patch now that we have all we need in the device tree
we can drop the boardfile.
---
arch/arm/mach-ixp4xx/Kconfig | 7 -
arch/arm/mach-ixp4xx/Makefile | 1 -
arch/arm/mach-ixp4xx/goramo_mlr.c | 532 -------------------
include/linux/platform_data/wan_ixp4xx_hss.h | 17 -
4 files changed, 557 deletions(-)
delete mode 100644 arch/arm/mach-ixp4xx/goramo_mlr.c
delete mode 100644 include/linux/platform_data/wan_ixp4xx_hss.h
diff --git a/arch/arm/mach-ixp4xx/Kconfig b/arch/arm/mach-ixp4xx/Kconfig
index 365a5853d310..c28e418a9a73 100644
--- a/arch/arm/mach-ixp4xx/Kconfig
+++ b/arch/arm/mach-ixp4xx/Kconfig
@@ -25,13 +25,6 @@ config MACH_GATEWAY7001
7001 Access Point. For more information on this platform,
see http://openwrt.org
-config MACH_GORAMO_MLR
- bool "GORAMO Multi Link Router"
- depends on IXP4XX_PCI_LEGACY
- help
- Say 'Y' here if you want your kernel to support GORAMO
- MultiLink router.
-
config ARCH_PRPMC1100
bool "PrPMC1100"
help
diff --git a/arch/arm/mach-ixp4xx/Makefile b/arch/arm/mach-ixp4xx/Makefile
index b241094c9649..1c8301036377 100644
--- a/arch/arm/mach-ixp4xx/Makefile
+++ b/arch/arm/mach-ixp4xx/Makefile
@@ -14,6 +14,5 @@ obj-pci-$(CONFIG_MACH_GATEWAY7001) += gateway7001-pci.o
obj-y += common.o
obj-$(CONFIG_MACH_GATEWAY7001) += gateway7001-setup.o
-obj-$(CONFIG_MACH_GORAMO_MLR) += goramo_mlr.o
obj-$(CONFIG_PCI) += $(obj-pci-$(CONFIG_PCI)) common-pci.o
diff --git a/arch/arm/mach-ixp4xx/goramo_mlr.c b/arch/arm/mach-ixp4xx/goramo_mlr.c
deleted file mode 100644
index 07b50dfcc489..000000000000
--- a/arch/arm/mach-ixp4xx/goramo_mlr.c
+++ /dev/null
@@ -1,532 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-/*
- * Goramo MultiLink router platform code
- * Copyright (C) 2006-2009 Krzysztof Halasa <khc at pm.waw.pl>
- */
-
-#include <linux/delay.h>
-#include <linux/gpio.h>
-#include <linux/hdlc.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/kernel.h>
-#include <linux/pci.h>
-#include <linux/platform_data/wan_ixp4xx_hss.h>
-#include <linux/serial_8250.h>
-#include <asm/mach-types.h>
-#include <asm/mach/arch.h>
-#include <asm/mach/flash.h>
-#include <asm/mach/pci.h>
-#include <asm/system_info.h>
-
-#include "irqs.h"
-
-#define SLOT_ETHA 0x0B /* IDSEL = AD21 */
-#define SLOT_ETHB 0x0C /* IDSEL = AD20 */
-#define SLOT_MPCI 0x0D /* IDSEL = AD19 */
-#define SLOT_NEC 0x0E /* IDSEL = AD18 */
-
-/* GPIO lines */
-#define GPIO_SCL 0
-#define GPIO_SDA 1
-#define GPIO_STR 2
-#define GPIO_IRQ_NEC 3
-#define GPIO_IRQ_ETHA 4
-#define GPIO_IRQ_ETHB 5
-#define GPIO_HSS0_DCD_N 6
-#define GPIO_HSS1_DCD_N 7
-#define GPIO_UART0_DCD 8
-#define GPIO_UART1_DCD 9
-#define GPIO_HSS0_CTS_N 10
-#define GPIO_HSS1_CTS_N 11
-#define GPIO_IRQ_MPCI 12
-#define GPIO_HSS1_RTS_N 13
-#define GPIO_HSS0_RTS_N 14
-/* GPIO15 is not connected */
-
-/* Control outputs from 74HC4094 */
-#define CONTROL_HSS0_CLK_INT 0
-#define CONTROL_HSS1_CLK_INT 1
-#define CONTROL_HSS0_DTR_N 2
-#define CONTROL_HSS1_DTR_N 3
-#define CONTROL_EXT 4
-#define CONTROL_AUTO_RESET 5
-#define CONTROL_PCI_RESET_N 6
-#define CONTROL_EEPROM_WC_N 7
-
-/* offsets from start of flash ROM = 0x50000000 */
-#define CFG_ETH0_ADDRESS 0x40 /* 6 bytes */
-#define CFG_ETH1_ADDRESS 0x46 /* 6 bytes */
-#define CFG_REV 0x4C /* u32 */
-#define CFG_SDRAM_SIZE 0x50 /* u32 */
-#define CFG_SDRAM_CONF 0x54 /* u32 */
-#define CFG_SDRAM_MODE 0x58 /* u32 */
-#define CFG_SDRAM_REFRESH 0x5C /* u32 */
-
-#define CFG_HW_BITS 0x60 /* u32 */
-#define CFG_HW_USB_PORTS 0x00000007 /* 0 = no NEC chip, 1-5 = ports # */
-#define CFG_HW_HAS_PCI_SLOT 0x00000008
-#define CFG_HW_HAS_ETH0 0x00000010
-#define CFG_HW_HAS_ETH1 0x00000020
-#define CFG_HW_HAS_HSS0 0x00000040
-#define CFG_HW_HAS_HSS1 0x00000080
-#define CFG_HW_HAS_UART0 0x00000100
-#define CFG_HW_HAS_UART1 0x00000200
-#define CFG_HW_HAS_EEPROM 0x00000400
-
-#define FLASH_CMD_READ_ARRAY 0xFF
-#define FLASH_CMD_READ_ID 0x90
-#define FLASH_SER_OFF 0x102 /* 0x81 in 16-bit mode */
-
-static u32 hw_bits = 0xFFFFFFFD; /* assume all hardware present */;
-static u8 control_value;
-
-/*
- * FIXME: this is reimplementing I2C bit-bangining. Move this
- * over to using driver/i2c/busses/i2c-gpio.c like all other boards
- * and register proper I2C device(s) on the bus for this. (See
- * other IXP4xx boards for examples.)
- */
-static void set_scl(u8 value)
-{
- gpio_set_value(GPIO_SCL, !!value);
- udelay(3);
-}
-
-static void set_sda(u8 value)
-{
- gpio_set_value(GPIO_SDA, !!value);
- udelay(3);
-}
-
-static void set_str(u8 value)
-{
- gpio_set_value(GPIO_STR, !!value);
- udelay(3);
-}
-
-static inline void set_control(int line, int value)
-{
- if (value)
- control_value |= (1 << line);
- else
- control_value &= ~(1 << line);
-}
-
-
-static void output_control(void)
-{
- int i;
-
- gpio_direction_output(GPIO_SCL, 1);
- gpio_direction_output(GPIO_SDA, 1);
-
- for (i = 0; i < 8; i++) {
- set_scl(0);
- set_sda(control_value & (0x80 >> i)); /* MSB first */
- set_scl(1); /* active edge */
- }
-
- set_str(1);
- set_str(0);
-
- set_scl(0);
- set_sda(1); /* Be ready for START */
- set_scl(1);
-}
-
-
-static void (*set_carrier_cb_tab[2])(void *pdev, int carrier);
-
-static int hss_set_clock(int port, unsigned int clock_type)
-{
- int ctrl_int = port ? CONTROL_HSS1_CLK_INT : CONTROL_HSS0_CLK_INT;
-
- switch (clock_type) {
- case CLOCK_DEFAULT:
- case CLOCK_EXT:
- set_control(ctrl_int, 0);
- output_control();
- return CLOCK_EXT;
-
- case CLOCK_INT:
- set_control(ctrl_int, 1);
- output_control();
- return CLOCK_INT;
-
- default:
- return -EINVAL;
- }
-}
-
-static irqreturn_t hss_dcd_irq(int irq, void *pdev)
-{
- int port = (irq == IXP4XX_GPIO_IRQ(GPIO_HSS1_DCD_N));
- int i = gpio_get_value(port ? GPIO_HSS1_DCD_N : GPIO_HSS0_DCD_N);
- set_carrier_cb_tab[port](pdev, !i);
- return IRQ_HANDLED;
-}
-
-
-static int hss_open(int port, void *pdev,
- void (*set_carrier_cb)(void *pdev, int carrier))
-{
- int i, irq;
-
- if (!port)
- irq = IXP4XX_GPIO_IRQ(GPIO_HSS0_DCD_N);
- else
- irq = IXP4XX_GPIO_IRQ(GPIO_HSS1_DCD_N);
-
- i = gpio_get_value(port ? GPIO_HSS1_DCD_N : GPIO_HSS0_DCD_N);
- set_carrier_cb(pdev, !i);
-
- set_carrier_cb_tab[!!port] = set_carrier_cb;
-
- if ((i = request_irq(irq, hss_dcd_irq, 0, "IXP4xx HSS", pdev)) != 0) {
- printk(KERN_ERR "ixp4xx_hss: failed to request IRQ%i (%i)\n",
- irq, i);
- return i;
- }
-
- set_control(port ? CONTROL_HSS1_DTR_N : CONTROL_HSS0_DTR_N, 0);
- output_control();
- gpio_set_value(port ? GPIO_HSS1_RTS_N : GPIO_HSS0_RTS_N, 0);
- return 0;
-}
-
-static void hss_close(int port, void *pdev)
-{
- free_irq(port ? IXP4XX_GPIO_IRQ(GPIO_HSS1_DCD_N) :
- IXP4XX_GPIO_IRQ(GPIO_HSS0_DCD_N), pdev);
- set_carrier_cb_tab[!!port] = NULL; /* catch bugs */
-
- set_control(port ? CONTROL_HSS1_DTR_N : CONTROL_HSS0_DTR_N, 1);
- output_control();
- gpio_set_value(port ? GPIO_HSS1_RTS_N : GPIO_HSS0_RTS_N, 1);
-}
-
-
-/* Flash memory */
-static struct flash_platform_data flash_data = {
- .map_name = "cfi_probe",
- .width = 2,
-};
-
-static struct resource flash_resource = {
- .flags = IORESOURCE_MEM,
-};
-
-static struct platform_device device_flash = {
- .name = "IXP4XX-Flash",
- .id = 0,
- .dev = { .platform_data = &flash_data },
- .num_resources = 1,
- .resource = &flash_resource,
-};
-
-/* IXP425 2 UART ports */
-static struct resource uart_resources[] = {
- {
- .start = IXP4XX_UART1_BASE_PHYS,
- .end = IXP4XX_UART1_BASE_PHYS + 0x0fff,
- .flags = IORESOURCE_MEM,
- },
- {
- .start = IXP4XX_UART2_BASE_PHYS,
- .end = IXP4XX_UART2_BASE_PHYS + 0x0fff,
- .flags = IORESOURCE_MEM,
- }
-};
-
-static struct plat_serial8250_port uart_data[] = {
- {
- .mapbase = IXP4XX_UART1_BASE_PHYS,
- .membase = (char __iomem *)IXP4XX_UART1_BASE_VIRT +
- REG_OFFSET,
- .irq = IRQ_IXP4XX_UART1,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- .iotype = UPIO_MEM,
- .regshift = 2,
- .uartclk = IXP4XX_UART_XTAL,
- },
- {
- .mapbase = IXP4XX_UART2_BASE_PHYS,
- .membase = (char __iomem *)IXP4XX_UART2_BASE_VIRT +
- REG_OFFSET,
- .irq = IRQ_IXP4XX_UART2,
- .flags = UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
- .iotype = UPIO_MEM,
- .regshift = 2,
- .uartclk = IXP4XX_UART_XTAL,
- },
- { },
-};
-
-static struct platform_device device_uarts = {
- .name = "serial8250",
- .id = PLAT8250_DEV_PLATFORM,
- .dev.platform_data = uart_data,
- .num_resources = 2,
- .resource = uart_resources,
-};
-
-
-/* Built-in 10/100 Ethernet MAC interfaces */
-static struct resource eth_npeb_resources[] = {
- {
- .start = IXP4XX_EthB_BASE_PHYS,
- .end = IXP4XX_EthB_BASE_PHYS + 0x0fff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct resource eth_npec_resources[] = {
- {
- .start = IXP4XX_EthC_BASE_PHYS,
- .end = IXP4XX_EthC_BASE_PHYS + 0x0fff,
- .flags = IORESOURCE_MEM,
- },
-};
-
-static struct eth_plat_info eth_plat[] = {
- {
- .phy = 0,
- .rxq = 3,
- .txreadyq = 32,
- }, {
- .phy = 1,
- .rxq = 4,
- .txreadyq = 33,
- }
-};
-
-static struct platform_device device_eth_tab[] = {
- {
- .name = "ixp4xx_eth",
- .id = IXP4XX_ETH_NPEB,
- .dev.platform_data = eth_plat,
- .num_resources = ARRAY_SIZE(eth_npeb_resources),
- .resource = eth_npeb_resources,
- }, {
- .name = "ixp4xx_eth",
- .id = IXP4XX_ETH_NPEC,
- .dev.platform_data = eth_plat + 1,
- .num_resources = ARRAY_SIZE(eth_npec_resources),
- .resource = eth_npec_resources,
- }
-};
-
-
-/* IXP425 2 synchronous serial ports */
-static struct hss_plat_info hss_plat[] = {
- {
- .set_clock = hss_set_clock,
- .open = hss_open,
- .close = hss_close,
- .txreadyq = 34,
- }, {
- .set_clock = hss_set_clock,
- .open = hss_open,
- .close = hss_close,
- .txreadyq = 35,
- }
-};
-
-static struct platform_device device_hss_tab[] = {
- {
- .name = "ixp4xx_hss",
- .id = 0,
- .dev.platform_data = hss_plat,
- }, {
- .name = "ixp4xx_hss",
- .id = 1,
- .dev.platform_data = hss_plat + 1,
- }
-};
-
-
-static struct platform_device *device_tab[7] __initdata = {
- &device_flash, /* index 0 */
-};
-
-static inline u8 __init flash_readb(u8 __iomem *flash, u32 addr)
-{
-#ifdef __ARMEB__
- return __raw_readb(flash + addr);
-#else
- return __raw_readb(flash + (addr ^ 3));
-#endif
-}
-
-static inline u16 __init flash_readw(u8 __iomem *flash, u32 addr)
-{
-#ifdef __ARMEB__
- return __raw_readw(flash + addr);
-#else
- return __raw_readw(flash + (addr ^ 2));
-#endif
-}
-
-static void __init gmlr_init(void)
-{
- u8 __iomem *flash;
- int i, devices = 1; /* flash */
-
- ixp4xx_sys_init();
-
- if ((flash = ioremap(IXP4XX_EXP_BUS_BASE_PHYS, 0x80)) == NULL)
- printk(KERN_ERR "goramo-mlr: unable to access system"
- " configuration data\n");
- else {
- system_rev = __raw_readl(flash + CFG_REV);
- hw_bits = __raw_readl(flash + CFG_HW_BITS);
-
- for (i = 0; i < ETH_ALEN; i++) {
- eth_plat[0].hwaddr[i] =
- flash_readb(flash, CFG_ETH0_ADDRESS + i);
- eth_plat[1].hwaddr[i] =
- flash_readb(flash, CFG_ETH1_ADDRESS + i);
- }
-
- __raw_writew(FLASH_CMD_READ_ID, flash);
- system_serial_high = flash_readw(flash, FLASH_SER_OFF);
- system_serial_high <<= 16;
- system_serial_high |= flash_readw(flash, FLASH_SER_OFF + 2);
- system_serial_low = flash_readw(flash, FLASH_SER_OFF + 4);
- system_serial_low <<= 16;
- system_serial_low |= flash_readw(flash, FLASH_SER_OFF + 6);
- __raw_writew(FLASH_CMD_READ_ARRAY, flash);
-
- iounmap(flash);
- }
-
- switch (hw_bits & (CFG_HW_HAS_UART0 | CFG_HW_HAS_UART1)) {
- case CFG_HW_HAS_UART0:
- memset(&uart_data[1], 0, sizeof(uart_data[1]));
- device_uarts.num_resources = 1;
- break;
-
- case CFG_HW_HAS_UART1:
- device_uarts.dev.platform_data = &uart_data[1];
- device_uarts.resource = &uart_resources[1];
- device_uarts.num_resources = 1;
- break;
- }
- if (hw_bits & (CFG_HW_HAS_UART0 | CFG_HW_HAS_UART1))
- device_tab[devices++] = &device_uarts; /* max index 1 */
-
- if (hw_bits & CFG_HW_HAS_ETH0)
- device_tab[devices++] = &device_eth_tab[0]; /* max index 2 */
- if (hw_bits & CFG_HW_HAS_ETH1)
- device_tab[devices++] = &device_eth_tab[1]; /* max index 3 */
-
- if (hw_bits & CFG_HW_HAS_HSS0)
- device_tab[devices++] = &device_hss_tab[0]; /* max index 4 */
- if (hw_bits & CFG_HW_HAS_HSS1)
- device_tab[devices++] = &device_hss_tab[1]; /* max index 5 */
-
- hss_plat[0].timer_freq = ixp4xx_timer_freq;
- hss_plat[1].timer_freq = ixp4xx_timer_freq;
-
- gpio_request(GPIO_SCL, "SCL/clock");
- gpio_request(GPIO_SDA, "SDA/data");
- gpio_request(GPIO_STR, "strobe");
- gpio_request(GPIO_HSS0_RTS_N, "HSS0 RTS");
- gpio_request(GPIO_HSS1_RTS_N, "HSS1 RTS");
- gpio_request(GPIO_HSS0_DCD_N, "HSS0 DCD");
- gpio_request(GPIO_HSS1_DCD_N, "HSS1 DCD");
-
- gpio_direction_output(GPIO_SCL, 1);
- gpio_direction_output(GPIO_SDA, 1);
- gpio_direction_output(GPIO_STR, 0);
- gpio_direction_output(GPIO_HSS0_RTS_N, 1);
- gpio_direction_output(GPIO_HSS1_RTS_N, 1);
- gpio_direction_input(GPIO_HSS0_DCD_N);
- gpio_direction_input(GPIO_HSS1_DCD_N);
- irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_HSS0_DCD_N), IRQ_TYPE_EDGE_BOTH);
- irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_HSS1_DCD_N), IRQ_TYPE_EDGE_BOTH);
-
- set_control(CONTROL_HSS0_DTR_N, 1);
- set_control(CONTROL_HSS1_DTR_N, 1);
- set_control(CONTROL_EEPROM_WC_N, 1);
- set_control(CONTROL_PCI_RESET_N, 1);
- output_control();
-
- msleep(1); /* Wait for PCI devices to initialize */
-
- flash_resource.start = IXP4XX_EXP_BUS_BASE(0);
- flash_resource.end = IXP4XX_EXP_BUS_BASE(0) + ixp4xx_exp_bus_size - 1;
-
- platform_add_devices(device_tab, devices);
-}
-
-
-#ifdef CONFIG_PCI
-static void __init gmlr_pci_preinit(void)
-{
- irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_IRQ_ETHA), IRQ_TYPE_LEVEL_LOW);
- irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_IRQ_ETHB), IRQ_TYPE_LEVEL_LOW);
- irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_IRQ_NEC), IRQ_TYPE_LEVEL_LOW);
- irq_set_irq_type(IXP4XX_GPIO_IRQ(GPIO_IRQ_MPCI), IRQ_TYPE_LEVEL_LOW);
- ixp4xx_pci_preinit();
-}
-
-static void __init gmlr_pci_postinit(void)
-{
- if ((hw_bits & CFG_HW_USB_PORTS) >= 2 &&
- (hw_bits & CFG_HW_USB_PORTS) < 5) {
- /* need to adjust number of USB ports on NEC chip */
- u32 value, addr = BIT(32 - SLOT_NEC) | 0xE0;
- if (!ixp4xx_pci_read(addr, NP_CMD_CONFIGREAD, &value)) {
- value &= ~7;
- value |= (hw_bits & CFG_HW_USB_PORTS);
- ixp4xx_pci_write(addr, NP_CMD_CONFIGWRITE, value);
- }
- }
-}
-
-static int __init gmlr_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
-{
- switch(slot) {
- case SLOT_ETHA: return IXP4XX_GPIO_IRQ(GPIO_IRQ_ETHA);
- case SLOT_ETHB: return IXP4XX_GPIO_IRQ(GPIO_IRQ_ETHB);
- case SLOT_NEC: return IXP4XX_GPIO_IRQ(GPIO_IRQ_NEC);
- default: return IXP4XX_GPIO_IRQ(GPIO_IRQ_MPCI);
- }
-}
-
-static struct hw_pci gmlr_hw_pci __initdata = {
- .nr_controllers = 1,
- .ops = &ixp4xx_ops,
- .preinit = gmlr_pci_preinit,
- .postinit = gmlr_pci_postinit,
- .setup = ixp4xx_setup,
- .map_irq = gmlr_map_irq,
-};
-
-static int __init gmlr_pci_init(void)
-{
- if (machine_is_goramo_mlr() &&
- (hw_bits & (CFG_HW_USB_PORTS | CFG_HW_HAS_PCI_SLOT)))
- pci_common_init(&gmlr_hw_pci);
- return 0;
-}
-
-subsys_initcall(gmlr_pci_init);
-#endif /* CONFIG_PCI */
-
-
-MACHINE_START(GORAMO_MLR, "MultiLink")
- /* Maintainer: Krzysztof Halasa */
- .map_io = ixp4xx_map_io,
- .init_early = ixp4xx_init_early,
- .init_irq = ixp4xx_init_irq,
- .init_time = ixp4xx_timer_init,
- .atag_offset = 0x100,
- .init_machine = gmlr_init,
-#if defined(CONFIG_PCI)
- .dma_zone_size = SZ_64M,
-#endif
- .restart = ixp4xx_restart,
-MACHINE_END
diff --git a/include/linux/platform_data/wan_ixp4xx_hss.h b/include/linux/platform_data/wan_ixp4xx_hss.h
deleted file mode 100644
index d525a0feb9e1..000000000000
--- a/include/linux/platform_data/wan_ixp4xx_hss.h
+++ /dev/null
@@ -1,17 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0 */
-#ifndef __PLATFORM_DATA_WAN_IXP4XX_HSS_H
-#define __PLATFORM_DATA_WAN_IXP4XX_HSS_H
-
-#include <linux/types.h>
-
-/* Information about built-in HSS (synchronous serial) interfaces */
-struct hss_plat_info {
- int (*set_clock)(int port, unsigned int clock_type);
- int (*open)(int port, void *pdev,
- void (*set_carrier_cb)(void *pdev, int carrier));
- void (*close)(int port, void *pdev);
- u8 txreadyq;
- u32 timer_freq;
-};
-
-#endif
--
2.31.1
More information about the linux-arm-kernel
mailing list