[PATCH V2 1/5] soc: imx: imx8m-blk-ctrl: Fix imx8mm mipi reset

[Laurent Pinchart]

Hi Adam,

On Sat, Nov 06, 2021 at 10:54:23AM -0500, Adam Ford wrote:
> Most of the blk-ctrl reset bits are found in one register, however
> there are two bits in offset 8 for pulling the MIPI DPHY out of reset
> and these need to be set when IMX8MM_DISPBLK_PD_MIPI_CSI is brought
> out of reset or the MIPI_CSI hangs.
> 
> Fixes: 926e57c065df ("soc: imx: imx8m-blk-ctrl: add DISP blk-ctrl")
> Signed-off-by: Adam Ford <aford173 at gmail.com>
> ---
> 
> V2:  Make a note that the extra register is only for Mini/Nano DISPLAY_BLK_CTRL
>      Rename the new register to mipi_phy_rst_mask
>      Encapsulate the edits to this register with an if-statement
> 
>  drivers/soc/imx/imx8m-blk-ctrl.c | 18 ++++++++++++++++++
>  1 file changed, 18 insertions(+)
> 
> diff --git a/drivers/soc/imx/imx8m-blk-ctrl.c b/drivers/soc/imx/imx8m-blk-ctrl.c
> index 519b3651d1d9..581eb4bc7f7d 100644
> --- a/drivers/soc/imx/imx8m-blk-ctrl.c
> +++ b/drivers/soc/imx/imx8m-blk-ctrl.c
> @@ -17,6 +17,7 @@
>  
>  #define BLK_SFT_RSTN	0x0
>  #define BLK_CLK_EN	0x4
> +#define BLK_MIPI_RESET_DIV	0x8 /* Mini/Nano DISPLAY_BLK_CTRL only */
>  
>  struct imx8m_blk_ctrl_domain;
>  
> @@ -36,6 +37,15 @@ struct imx8m_blk_ctrl_domain_data {
>  	const char *gpc_name;
>  	u32 rst_mask;
>  	u32 clk_mask;
> +
> +	/*
> +	 * i.MX8M Mini and Nano have a third DISPLAY_BLK_CTRL register
> +	 * which is used to control the reset for the MIPI Phy.
> +	 * Since it's only present in certain circumstances,
> +	 * an if-statement should be used before setting and clearing this
> +	 * register.
> +	 */
> +	u32 mipi_phy_rst_mask;
>  };
>  
>  #define DOMAIN_MAX_CLKS 3
> @@ -78,6 +88,8 @@ static int imx8m_blk_ctrl_power_on(struct generic_pm_domain *genpd)
>  
>  	/* put devices into reset */
>  	regmap_clear_bits(bc->regmap, BLK_SFT_RSTN, data->rst_mask);
> +	if (data->mipi_phy_rst_mask)
> +		regmap_clear_bits(bc->regmap, BLK_MIPI_RESET_DIV, data->mipi_phy_rst_mask);
>  
>  	/* enable upstream and blk-ctrl clocks to allow reset to propagate */
>  	ret = clk_bulk_prepare_enable(data->num_clks, domain->clks);
> @@ -99,6 +111,8 @@ static int imx8m_blk_ctrl_power_on(struct generic_pm_domain *genpd)
>  
>  	/* release reset */
>  	regmap_set_bits(bc->regmap, BLK_SFT_RSTN, data->rst_mask);
> +	if (data->mipi_phy_rst_mask)
> +		regmap_set_bits(bc->regmap, BLK_MIPI_RESET_DIV, data->mipi_phy_rst_mask);
>  
>  	/* disable upstream clocks */
>  	clk_bulk_disable_unprepare(data->num_clks, domain->clks);
> @@ -120,6 +134,9 @@ static int imx8m_blk_ctrl_power_off(struct generic_pm_domain *genpd)
>  	struct imx8m_blk_ctrl *bc = domain->bc;
>  
>  	/* put devices into reset and disable clocks */
> +	if (data->mipi_phy_rst_mask)
> +		regmap_clear_bits(bc->regmap, BLK_MIPI_RESET_DIV, data->mipi_phy_rst_mask);
> +

Is it the best option to enable/disable both the master and slave MIPI
DPHY, regardless of whether they're used or not ? Or would it be better
to implement a reset controller to expose the two resets independently,
and acquire them from the corresponding display and camera drivers ?

>  	regmap_clear_bits(bc->regmap, BLK_SFT_RSTN, data->rst_mask);
>  	regmap_clear_bits(bc->regmap, BLK_CLK_EN, data->clk_mask);
>  
> @@ -488,6 +505,7 @@ static const struct imx8m_blk_ctrl_domain_data imx8mm_disp_blk_ctl_domain_data[]
>  		.gpc_name = "mipi-csi",
>  		.rst_mask = BIT(3) | BIT(4),
>  		.clk_mask = BIT(10) | BIT(11),
> +		.mipi_phy_rst_mask = BIT(16) | BIT(17),
>  	},
>  };
>  

-- 
Regards,

Laurent Pinchart