[PATCH v2] thermal: imx: implement runtime PM support

[Oleksij Rempel]

On Mon, Nov 15, 2021 at 04:02:07PM +0100, Petr Benes wrote:
> Hi Oleksij,
> 
> On Thu, 11 Nov 2021 at 10:16, Oleksij Rempel <o.rempel at pengutronix.de> wrote:
> >
> > On Wed, Nov 10, 2021 at 11:07:31AM +0100, Michal Vokáč wrote:
> > > On 25. 10. 21 13:06, Petr Benes wrote:
> > > > Hi Oleksij,
> > > >
> > > > On Thu, 21 Oct 2021 at 19:21, Oleksij Rempel <o.rempel at pengutronix.de> wrote:
> > > > >
> > > > > Hi Petr,
> > > > >
> > > > > On Wed, Oct 20, 2021 at 05:53:03PM +0200, Petr Benes wrote:
> > > > > > On Wed, 20 Oct 2021 at 07:05, Oleksij Rempel <o.rempel at pengutronix.de> wrote:
> > > > > > >
> > > > > > > Hi Petr and Michal,
> > > > > > >
> > > > > > > I forgot to add you for v2 in CC. Please test/review this version.
> > > > > >
> > > > > > Hi Oleksij,
> > > > > >
> > > > > > It works good. with PM as well as without PM. The only minor issue I found is,
> > > > > > that the first temperature reading (when the driver probes) fails. That is
> > > > > > (val & soc_data->temp_valid_mask) == 0) holds true. How does
> > > > > > pm_runtime_resume_and_get() behave in imx_thermal_probe()?
> > > > > > Does it go through imx_thermal_runtime_resume() with usleep_range()?
> > > > >
> > > > > How exactly did you reproduce it? Even more or less understanding how
> > > >
> > > > I just placed my debug print into get_temp()
> > > >
> > > >      if ((val & soc_data->temp_valid_mask) == 0) {
> > > >          dev_dbg(&tz->device, "temp measurement never finished\n");
> > > >          printk("Wrong temperature reading!!!!!!\n");
> > > >          return -EAGAIN;
> > > >      }
> > > >
> > > > > this can potentially happen, i never had this issue on my HW. Is it something
> > > > > HW specific?
> > > >
> > > > IMHO it is just product of the following sequence:
> > > >
> > > > pm_runtime_set_active(&pdev->dev);
> > > > pm_runtime_enable(data->dev);
> > > > pm_runtime_resume_and_get(data->dev);
> > > > thermal_zone_device_enable(data->tz);
> > > >
> > > > With assumption imx_thermal_runtime_resume() didn't run,
> > > > hence the sensor didn't get enough time to come up.
> > > >
> > > > I didn't have time to spend it on and you have better knowledge of the
> > > > area. If it is not that straightforward I can try to diagnose it better.
> > > >
> > > Hi Oleksij,
> > > Did you manage to further debug and reproduce this problem?
> > > Do you plan to send the v3?
> > >
> > > Regarding your question about the HW - this problem occured once we
> > > upgraded the SoC on our SBC from i.MX6DL to i.MX6Q/QP. With the DualLite
> > > we never had this problem but the Quad is getting hot quite fast.
> > > We have pretty limited cooling options so the core is operated at its
> > > upper temperature limits when fully loaded.
> >
> > Hi Michal,
> >
> > Sorry, I was busy and lost this topic from my radar. I was not able to
> > reproduce it on my i.MX6Q and i.MX6QP died after other thermal voltage
> > experiments. Please, if you able to reproduce it, try to investigate
> > what is wrong, for example increasing wakeup time and/or and tracing
> > sleap/wake/get sequences.
> 
> Seems it is just as easy as calling usleep_range(20, 50) when you switch on
> the sensor and enable temperature measurement in imx_thermal_probe().
> So, we are sure the sensor is configured and _ready_.
> 
> You call pm_runtime_set_active(), pm_runtime_enable(), and
> pm_runtime_resume_and_get(). The last one doesn't call the resume
> callback (which correctly handles waiting for the sensor) as the device
> is already active.

Ok, thx! It makes sense. I'll send new version with the fix.

Regards,
Oleksij
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |