[PATCH 10/16] serial: sh-sci: Add support for RZ/G2L SoC

[Geert Uytterhoeven]

Hi Prabhakar,

On Fri, May 14, 2021 at 9:23 PM Lad Prabhakar
<prabhakar.mahadev-lad.rj at bp.renesas.com> wrote:
> From: Biju Das <biju.das.jz at bp.renesas.com>
>
> Add serial support for RZ/G2L SoC with earlycon and
> extended mode register support.
>
> Signed-off-by: Biju Das <biju.das.jz at bp.renesas.com>
> Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj at bp.renesas.com>

Thanks for your patch!

> --- a/drivers/tty/serial/sh-sci.c
> +++ b/drivers/tty/serial/sh-sci.c
> @@ -306,6 +306,7 @@ static const struct sci_port_params sci_port_params[SCIx_NR_REGTYPES] = {
>                         [SCFDR]         = { 0x0E, 16 },
>                         [SCSPTR]        = { 0x10, 16 },
>                         [SCLSR]         = { 0x12, 16 },
> +                       [SEMR]          = { 0x14, 8 },

This is the parameter section for RZ/T and RZ/A2.  Please update the
comments above, to say this also applies to RZ/G2L.
I can confirm the documentation for RZ/T1 and RZ/A2 agrees about the
existence and behavior of SEMR.

>                 },
>                 .fifosize = 16,
>                 .overrun_reg = SCLSR,
> @@ -2527,6 +2528,8 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
>                         case 27: smr_val |= SCSMR_SRC_27; break;
>                         }
>                 smr_val |= cks;
> +               if (sci_getreg(port, SEMR)->size)
> +                       serial_port_out(port, SEMR, 0);

As this is done in both branches of the if() statement, I think it
should be moved up.

>                 serial_port_out(port, SCSCR, scr_val | s->hscif_tot);
>                 serial_port_out(port, SCSMR, smr_val);
>                 serial_port_out(port, SCBRR, brr);
> @@ -2561,6 +2564,8 @@ static void sci_set_termios(struct uart_port *port, struct ktermios *termios,
>                 scr_val = s->cfg->scscr & (SCSCR_CKE1 | SCSCR_CKE0);
>                 smr_val |= serial_port_in(port, SCSMR) &
>                            (SCSMR_CKEDG | SCSMR_SRC_MASK | SCSMR_CKS);
> +               if (sci_getreg(port, SEMR)->size)
> +                       serial_port_out(port, SEMR, 0);

(else branch)

>                 serial_port_out(port, SCSCR, scr_val | s->hscif_tot);
>                 serial_port_out(port, SCSMR, smr_val);
>         }
> @@ -3170,6 +3175,10 @@ static const struct of_device_id of_sci_match[] = {
>                 .compatible = "renesas,scif-r7s9210",
>                 .data = SCI_OF_DATA(PORT_SCIF, SCIx_RZ_SCIFA_REGTYPE),
>         },
> +       {
> +               .compatible = "renesas,scif-r9a07g044",
> +               .data = SCI_OF_DATA(PORT_SCIF, SCIx_RZ_SCIFA_REGTYPE),
> +       },
>         /* Family-specific types */
>         {
>                 .compatible = "renesas,rcar-gen1-scif",

The rest looks good to me.

Gr{oetje,eeting}s,

                        Geert

--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds