[PATCH v3 3/4] arm64: dts: imx8mq-nitrogen: add lt8912 MIPI-DSI to HDMI

[Shawn Guo]

On Thu, Apr 01, 2021 at 01:23:55AM +0200, Adrien Grassein wrote:
> Add support of the lt8912b in the DTB.
> This adds the support of the DB_DSIHD daugther board from
> Boundary Devices.
> 
> Signed-off-by: Adrien Grassein <adrien.grassein at gmail.com>
> ---
>  .../boot/dts/freescale/imx8mq-nitrogen.dts    | 120 ++++++++++++++++++
>  1 file changed, 120 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
> index 04992cbba56e..4ffd23ea705f 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mq-nitrogen.dts
> @@ -34,6 +34,19 @@ power {
>  		};
>  	};
>  
> +	hdmi-connector {
> +		compatible = "hdmi-connector";
> +		ddc-i2c-bus = <&ddc_i2c_bus>;
> +		label = "hdmi";
> +		type = "a";
> +
> +		port {
> +			hdmi_connector_in: endpoint {
> +				remote-endpoint = <&lt8912_out>;
> +			};
> +		};
> +	};
> +
>  	reg_usb_otg_vbus: regulator-usb-otg-vbus {
>  		compatible = "regulator-fixed";
>  		pinctrl-names = "default";
> @@ -81,6 +94,9 @@ reg_vref_5v: regulator-vref-5v {
>  	};
>  };
>  
> +&dphy {
> +	status = "okay";
> +};
>  
>  &fec1 {
>  	pinctrl-names = "default";
> @@ -193,6 +209,97 @@ rtc at 68 {
>  	};
>  };
>  
> +&i2c4 {
> +	clock-frequency = <100000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c4>;
> +	status = "okay";
> +
> +	pca9546: i2cmux9546 at 70 {

Node name should be generic, so 9546 should be dropped from there?

> +		compatible = "nxp,pca9546";
> +		reg = <0x70>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		i2c4 at 0 {

Is number 4 really needed in node name?

> +			reg = <0>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			clock-frequency = <100000>;
> +
> +			hdmi-bridge at 48 {
> +				compatible = "lontium,lt8912b";
> +				reg = <0x48> ;
> +				reset-gpios = <&max7323 0 GPIO_ACTIVE_LOW>;
> +
> +				ports {
> +					#address-cells = <1>;
> +					#size-cells = <0>;
> +
> +					port at 0 {
> +						reg = <0>;
> +
> +						hdmi_out_in: endpoint {
> +							data-lanes = <1 2 3 4>;
> +							remote-endpoint = <&mipi_dsi_out>;
> +						};
> +					};
> +
> +					port at 1 {
> +						reg = <1>;
> +
> +						lt8912_out: endpoint {
> +							remote-endpoint = <&hdmi_connector_in>;
> +						};
> +					};
> +				};
> +			};
> +		};
> +
> +		ddc_i2c_bus: i2c4 at 1 {
> +			reg = <1>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			clock-frequency = <100000>;
> +		};
> +
> +		i2c4 at 3 {
> +			reg = <3>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			clock-frequency = <100000>;
> +
> +			max7323: max7323 at 68 {

Can we have a generic node name for this device?

> +				compatible = "maxim,max7323";
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&pinctrl_max7323>;
> +				gpio-controller;
> +				reg = <0x68>;
> +				#gpio-cells = <2>;
> +			};
> +		};
> +	};
> +};
> +
> +&lcdif {
> +	status = "okay";
> +};
> +
> +&mipi_dsi {
> +	status = "okay";

Move it to end of property list.

> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	ports {
> +		port at 1 {
> +			reg = <1>;

Newline between property and child node.

Shawn

> +			mipi_dsi_out: endpoint {
> +				remote-endpoint = <&hdmi_out_in>;
> +			};
> +		};
> +	};
> +};
> +
>  &uart1 { /* console */
>  	pinctrl-names = "default";
>  	pinctrl-0 = <&pinctrl_uart1>;
> @@ -368,6 +475,19 @@ MX8MQ_IOMUXC_GPIO1_IO06_GPIO1_IO6		0x49
>  		>;
>  	};
>  
> +	pinctrl_i2c4: i2c4grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_I2C4_SCL_I2C4_SCL			0x4000007f
> +			MX8MQ_IOMUXC_I2C4_SDA_I2C4_SDA			0x4000007f
> +		>;
> +	};
> +
> +	pinctrl_max7323: max7323grp {
> +		fsl,pins = <
> +			MX8MQ_IOMUXC_NAND_RE_B_GPIO3_IO15 0x19
> +		>;
> +	};
> +
>  	pinctrl_reg_arm_dram: reg-arm-dramgrp {
>  		fsl,pins = <
>  			MX8MQ_IOMUXC_SAI5_RXD3_GPIO3_IO24	0x16
> -- 
> 2.25.1
>