[PATCHv1 3/9] soc: amlogic: meson-ee-pwrc: Add hdmi power domain Meson g12a SoCs

Anand Moon linux.amoon at gmail.com
Mon May 3 09:37:41 PDT 2021


hi Martin

On Mon, 3 May 2021 at 21:05, Martin Blumenstingl
<martin.blumenstingl at googlemail.com> wrote:
>
> Hi Anand,
>
> On Mon, May 3, 2021 at 5:29 PM Anand Moon <linux.amoon at gmail.com> wrote:
> [...]
> > > > +static struct meson_ee_pwrc_mem_domain meson_pwrc_mem_hdmi[] = {
> > > > +       { HHI_MEM_PD_REG0, GENMASK(15, 8) },
> > > > +};
> > > > +
> > > the VPU power domain already includes:
> > >   VPU_HHI_MEMPD(HHI_MEM_PD_REG0),
> > > whereas VPU_HHI_MEMPD is bits[15:8]
> > >
> > > Having two power domains which are managing the same registers sounds
> > > like it'll be causing some trouble
> > > So for now this is (as I am not even sure what the goal here is):
> > > NACKed-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> > >
> >
> > Ok, thanks. On the line of Ethernet PD, I tried to add this accordingly.
> From what I understand the VPU power domain is special because the
> display pipeline consists of multiple components (HDMI, VPU, ...)
> that's why the handling currently is special
>
> > whenever I try something new it fails. Please ignore this series.
> if the VPU and HDMI power domains were separate (from hardware
> perspective, not from driver perspective) then your change is a good
> step forward.
> in that case VPU_HHI_MEMPD would need to be removed from wherever it's
> currently used -> that means we need to also decide if we want to
> break compatibility with older (before this series) .dtbs
>
>

As per the datasheet S922X Datasheet, HDMI and VPU are different
reg controller and they are independent of each other.

*HHI_MEM_PD_REG0 0x40*

17~16  R/W 0x3 DDR memory PD
*15~8 R/W 0xFF HDMI memory PD*
7~6 R/W 0x3 Reserved
5~4 R/W 0x3 Audio mem PD
3~2 R/W 0x3 Ethernet memory PD
1~0 R/W 0x3 resved

Note: HDMI and AUDIO and Ethernet are also independent of each other.

*HHI_VPU_MEM_PD_REG0 0x41 *

31~30 R/W 0x3 sharp
29~28 R/W 0x3 Deinterlacer – di_post: 11 = power down. 00 = normal operation
27~26 R/W 0x3 Deinterlacer – di_pre 25~24 R/W 0x3 Vi_di_scaler
23~22 R/W 0x3 afbc_dec1
21~20 R/W 0x3 Srscl super scaler
19~18 R/W 0x3 Vdin1 memory
17~16 R/W 0x3 Vdin0 memory
15~14 R/W 0x3 Osd_scaler memory
13~12 R/W 0x3 Scaler memory
11~10 R/W 0x3 Vpp output fifo
9~8 R/W 0x3 Color management module
7~6 R/W 0x3 Vd2 memory
5~4 R/W 0x3 Vd1 memory
3~2 R/W 0x3 Osd2 memory
1~0 R/W 0x3 Osd1 memory

Below is the output on Odroid N2.

[alarm at archl-on2 ~]$ sudo cat /sys/kernel/debug/pm_genpd/pm_genpd_summary
domain                          status          children
            performance
    /device                                             runtime status
----------------------------------------------------------------------------------------------
HDMI                            on
            0
    /devices/platform/soc/ff600000.bus/ff600000.hdmi-tx  unsupported
             0
AUDIO                           on
            0
    /devices/platform/sound                             unsupported
            0
ETH                             on
            0
    /devices/platform/soc/ff3f0000.ethernet             active
            0
VPU                             on
            0
    /devices/platform/soc/ff900000.vpu                  unsupported
            0

HDMI power domain is ON.
Audio is wrongly mapped.

> Best regards,
> Martin

-Anand



More information about the linux-arm-kernel mailing list