[RFC PATCH 1/6] spi: spi-mem: Tell controller when device is ready for calibration

Michael Walle michael at walle.cc
Tue Mar 23 23:07:46 GMT 2021


Hi Pratyush,

Am 2021-03-11 20:12, schrieb Pratyush Yadav:
> Some controllers like the Cadence OSPI controller need to perform a
> calibration sequence to operate at high clock speeds. This calibration
> should happen after the flash is fully initialized otherwise the
> calibration might happen in a different SPI mode from the one the flash
> is finally set to. Add a hook that can be used to tell the controller
> when the flash is ready for calibration. Whether calibration is needed
> depends on the controller.
> 
> Signed-off-by: Pratyush Yadav <p.yadav at ti.com>
> ---
>  drivers/spi/spi-mem.c       | 12 ++++++++++++
>  include/linux/spi/spi-mem.h |  8 ++++++++
>  2 files changed, 20 insertions(+)
> 
> diff --git a/drivers/spi/spi-mem.c b/drivers/spi/spi-mem.c
> index dc713b0c3c4d..e2f05ad3f4dc 100644
> --- a/drivers/spi/spi-mem.c
> +++ b/drivers/spi/spi-mem.c
> @@ -464,6 +464,18 @@ int spi_mem_adjust_op_size(struct spi_mem *mem,
> struct spi_mem_op *op)
>  }
>  EXPORT_SYMBOL_GPL(spi_mem_adjust_op_size);
> 
> +int spi_mem_do_calibration(struct spi_mem *mem, struct spi_mem_op *op)
> +{
> +	struct spi_controller *ctlr = mem->spi->controller;
> +
> +	if (!ctlr->mem_ops || !ctlr->mem_ops->do_calibration)
> +		return -EOPNOTSUPP;
> +
> +	ctlr->mem_ops->do_calibration(mem, op);

Can't a calibration fail?

> +	return 0;
> +}
> +EXPORT_SYMBOL_GPL(spi_mem_do_calibration);
> +
>  static ssize_t spi_mem_no_dirmap_read(struct spi_mem_dirmap_desc 
> *desc,
>  				      u64 offs, size_t len, void *buf)
>  {
> diff --git a/include/linux/spi/spi-mem.h b/include/linux/spi/spi-mem.h
> index 2b65c9edc34e..97a2d280f2d0 100644
> --- a/include/linux/spi/spi-mem.h
> +++ b/include/linux/spi/spi-mem.h
> @@ -250,6 +250,12 @@ static inline void *spi_mem_get_drvdata(struct
> spi_mem *mem)
>   *		  the currently mapped area), and the caller of
>   *		  spi_mem_dirmap_write() is responsible for calling it again in
>   *		  this case.
> + * @do_calibration: perform calibration needed for high SPI clock 
> speed
> + *		    operation. Should be called after the SPI memory device has
> + *		    been completely initialized. The op passed should contain
> + *		    a template for the read operation used for the device so
> + *		    the controller can decide what type of calibration is
> + *		    required for this type of read.
>   *
>   * This interface should be implemented by SPI controllers providing 
> an
>   * high-level interface to execute SPI memory operation, which is 
> usually the
> @@ -274,6 +280,7 @@ struct spi_controller_mem_ops {
>  			       u64 offs, size_t len, void *buf);
>  	ssize_t (*dirmap_write)(struct spi_mem_dirmap_desc *desc,
>  				u64 offs, size_t len, const void *buf);
> +	void (*do_calibration)(struct spi_mem *mem, struct spi_mem_op *op);
>  };
> 
>  /**
> @@ -346,6 +353,7 @@ bool spi_mem_dtr_supports_op(struct spi_mem *mem,
>  #endif /* CONFIG_SPI_MEM */
> 
>  int spi_mem_adjust_op_size(struct spi_mem *mem, struct spi_mem_op 
> *op);
> +int spi_mem_do_calibration(struct spi_mem *mem, struct spi_mem_op 
> *op);
> 
>  bool spi_mem_supports_op(struct spi_mem *mem,
>  			 const struct spi_mem_op *op);

-- 
-michael



More information about the linux-arm-kernel mailing list