[v3,2/3] thermal: mediatek: Add LVTS drivers for SoC theraml zones

Michael Kao michael.kao at mediatek.com
Fri Mar 12 03:40:17 GMT 2021


Add a LVTS (Low voltage thermal sensor) driver to report junction
temperatures in Mediatek SoC and register the maximum temperature
of sensors and each sensor as a thermal zone.

Signed-off-by: Yu-Chia Chang <ethan.chang at mediatek.com>
Signed-off-by: Michael Kao <michael.kao at mediatek.com>
---
 drivers/thermal/mediatek/Kconfig         |   10 +
 drivers/thermal/mediatek/Makefile        |    1 +
 drivers/thermal/mediatek/soc_temp_lvts.c | 1287 ++++++++++++++++++++++
 drivers/thermal/mediatek/soc_temp_lvts.h |  312 ++++++
 4 files changed, 1610 insertions(+)
 create mode 100644 drivers/thermal/mediatek/soc_temp_lvts.c
 create mode 100644 drivers/thermal/mediatek/soc_temp_lvts.h

diff --git a/drivers/thermal/mediatek/Kconfig b/drivers/thermal/mediatek/Kconfig
index 0351e73170b7..d716d0372e1e 100644
--- a/drivers/thermal/mediatek/Kconfig
+++ b/drivers/thermal/mediatek/Kconfig
@@ -20,4 +20,14 @@ config MTK_SOC_THERMAL
 	  configures thermal controllers to collect temperature
 	  via AUXADC interface.
 
+config MTK_SOC_THERMAL_LVTS
+        tristate "LVTS (Low voltage thermal sensor) driver for Mediatek SoCs"
+        depends on HAS_IOMEM
+        depends on NVMEM
+        depends on RESET_TI_SYSCON
+        help
+          Enable this option if you want to get SoC temperature
+          information for Mediatek platforms. This driver
+          configures LVTS thermal controllers to collect temperatures
+          via Analog Serial Interface(ASIF).
 endif
diff --git a/drivers/thermal/mediatek/Makefile b/drivers/thermal/mediatek/Makefile
index f75313ddce5e..16ce166e5916 100644
--- a/drivers/thermal/mediatek/Makefile
+++ b/drivers/thermal/mediatek/Makefile
@@ -1 +1,2 @@
 obj-$(CONFIG_MTK_SOC_THERMAL)	+= soc_temp.o
+obj-$(CONFIG_MTK_SOC_THERMAL_LVTS)	+= soc_temp_lvts.o
diff --git a/drivers/thermal/mediatek/soc_temp_lvts.c b/drivers/thermal/mediatek/soc_temp_lvts.c
new file mode 100644
index 000000000000..8153edaaf815
--- /dev/null
+++ b/drivers/thermal/mediatek/soc_temp_lvts.c
@@ -0,0 +1,1287 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 MediaTek Inc.
+ */
+
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/thermal.h>
+#include "soc_temp_lvts.h"
+
+/*==================================================
+ * Definition or macro function
+ *==================================================
+ */
+#define STOP_COUNTING_V4 (DEVICE_WRITE | RG_TSFM_CTRL_0 << 8 | 0x00)
+#define SET_RG_TSFM_LPDLY_V4 (DEVICE_WRITE | RG_TSFM_CTRL_4 << 8 | 0xA6)
+#define SET_COUNTING_WINDOW_20US1_V4 (DEVICE_WRITE | RG_TSFM_CTRL_2 << 8 | 0x00)
+#define SET_COUNTING_WINDOW_20US2_V4 (DEVICE_WRITE | RG_TSFM_CTRL_1 << 8 | 0x20)
+#define TSV2F_CHOP_CKSEL_AND_TSV2F_EN_V4 (DEVICE_WRITE | RG_TSV2F_CTRL_2 << 8 | 0x84)
+#define TSBG_DEM_CKSEL_X_TSBG_CHOP_EN_V4 (DEVICE_WRITE | RG_TSV2F_CTRL_4 << 8 | 0x7C)
+#define SET_TS_RSV_V4 (DEVICE_WRITE | RG_TSV2F_CTRL_1 << 8 | 0x8D)
+#define SET_TS_EN_V4 (DEVICE_WRITE | RG_TSV2F_CTRL_0 << 8 | 0xF4)
+#define TOGGLE_RG_TSV2F_VCO_RST1_V4 (DEVICE_WRITE | RG_TSV2F_CTRL_0 << 8 | 0xFC)
+#define TOGGLE_RG_TSV2F_VCO_RST2_V4 (DEVICE_WRITE | RG_TSV2F_CTRL_0 << 8 | 0xF4)
+
+#define SET_LVTS_AUTO_RCK_V4 (DEVICE_WRITE | RG_TSV2F_CTRL_6 << 8 | 0x01)
+#define SELECT_SENSOR_RCK_V4(id) (DEVICE_WRITE | RG_TSV2F_CTRL_5 << 8 | (id))
+#define SET_DEVICE_SINGLE_MODE_V4 (DEVICE_WRITE | RG_TSFM_CTRL_3 << 8 | 0x78)
+#define KICK_OFF_RCK_COUNTING_V4 (DEVICE_WRITE | RG_TSFM_CTRL_0 << 8 | 0x02)
+#define SET_SENSOR_NO_RCK_V4 (DEVICE_WRITE | RG_TSV2F_CTRL_5 << 8 | 0x10)
+#define SET_DEVICE_LOW_POWER_SINGLE_MODE_V4 (DEVICE_WRITE | RG_TSFM_CTRL_3 << 8	| 0xB8)
+
+#define ENABLE_FEATURE(feature)		(lvts_data->feature_bitmap |= (feature))
+#define DISABLE_FEATURE(feature)	(lvts_data->feature_bitmap &= (~(feature)))
+#define IS_ENABLE(feature)		(lvts_data->feature_bitmap & (feature))
+
+#define DISABLE_THERMAL_HW_REBOOT (-274000)
+
+#define CLOCK_26MHZ_CYCLE_NS	(38)
+#define BUS_ACCESS_US		(2)
+
+#define FEATURE_DEVICE_AUTO_RCK	(BIT(0))
+#define FEATURE_CK26M_ACTIVE	(BIT(1))
+#define CK26M_ACTIVE   (((lvts_data->feature_bitmap & FEATURE_CK26M_ACTIVE)    \
+			? 1 : 0) << 30)
+#define GET_BASE_ADDR(tc_id)	\
+	(lvts_data->domain[lvts_data->tc[tc_id].domain_index].base	\
+	+ lvts_data->tc[tc_id].addr_offset)
+
+#define SET_TC_SPEED_IN_US(pu, gd, fd, sd) \
+	{	\
+		.period_unit = (((pu) * 1000) / (256 * CLOCK_26MHZ_CYCLE_NS)),	\
+		.group_interval_delay = ((gd) / (pu)),	\
+		.filter_interval_delay = ((fd) / (pu)),	\
+		.sensor_interval_delay = ((sd) / (pu)),	\
+	}
+
+#define GET_CAL_DATA_BITMASK(index, h, l)	\
+	(((index) < lvts_data->num_efuse_addr)	\
+	? ((lvts_data->efuse[(index)] & GENMASK(h, l)) >> l)	\
+	: 0)
+
+#define GET_CAL_DATA_BIT(index, bit)	\
+	(((index) < lvts_data->num_efuse_addr)	\
+	? ((lvts_data->efuse[index] & BIT(bit)) >> (bit))	\
+	: 0)
+
+#define GET_TC_SENSOR_NUM(tc_id)	\
+	(lvts_data->tc[tc_id].num_sensor)
+
+#define ONE_SAMPLE (lvts_data->counting_window_us + 2 * BUS_ACCESS_US)
+
+#define NUM_OF_SAMPLE(tc_id)	\
+	((lvts_data->tc[tc_id].hw_filter < LVTS_FILTER_2) ? 1 :	\
+	((lvts_data->tc[tc_id].hw_filter > LVTS_FILTER_16_OF_18) ? 1 :	\
+	((lvts_data->tc[tc_id].hw_filter == LVTS_FILTER_16_OF_18) ? 18 :\
+	((lvts_data->tc[tc_id].hw_filter == LVTS_FILTER_8_OF_10) ? 10 :	\
+	(lvts_data->tc[tc_id].hw_filter * 2)))))
+
+#define PERIOD_UNIT_US(tc_id)	\
+	((lvts_data->tc[tc_id].tc_speed.period_unit * 256 *	\
+	CLOCK_26MHZ_CYCLE_NS) / 1000)
+#define FILTER_INT_US(tc_id)	\
+	(lvts_data->tc[tc_id].tc_speed.filter_interval_delay	\
+	* PERIOD_UNIT_US(tc_id))
+#define SENSOR_INT_US(tc_id)	\
+	(lvts_data->tc[tc_id].tc_speed.sensor_interval_delay	\
+	* PERIOD_UNIT_US(tc_id))
+#define GROUP_INT_US(tc_id)	\
+	(lvts_data->tc[tc_id].tc_speed.group_interval_delay	\
+	* PERIOD_UNIT_US(tc_id))
+
+#define SENSOR_LATENCY_US(tc_id) \
+	((NUM_OF_SAMPLE(tc_id) - 1) * FILTER_INT_US(tc_id)	\
+	+ NUM_OF_SAMPLE(tc_id) * ONE_SAMPLE)
+
+#define GROUP_LATENCY_US(tc_id)	\
+	(GET_TC_SENSOR_NUM(tc_id) * SENSOR_LATENCY_US(tc_id)	\
+	+ (GET_TC_SENSOR_NUM(tc_id) - 1) * SENSOR_INT_US(tc_id)	\
+	+ GROUP_INT_US(tc_id))
+
+/*==================================================
+ * LVTS local common code
+ *==================================================
+ */
+static int lvts_raw_to_temp(struct formula_coeff *co, unsigned int msr_raw)
+{
+	/* This function returns degree mC */
+
+	int temp;
+
+	temp = (co->a * ((unsigned long long)msr_raw)) >> 14;
+	temp = temp + co->golden_temp * 500 + co->b;
+
+	return temp;
+}
+
+static unsigned int lvts_temp_to_raw(struct formula_coeff *co, int temp)
+{
+	unsigned int msr_raw;
+
+	msr_raw = div_s64((s64)((co->golden_temp * 500 + co->b - temp)) << 14,
+			 (-1 * co->a));
+
+	return msr_raw;
+}
+
+static int lvts_read_all_tc_temperature(struct lvts_data *lvts_data)
+{
+	struct tc_settings *tc = lvts_data->tc;
+	unsigned int i, j, s_index, msr_raw;
+	int max_temp = 0, current_temp;
+	void __iomem *base;
+
+	for (i = 0; i < lvts_data->num_tc; i++) {
+		base = GET_BASE_ADDR(i);
+		for (j = 0; j < tc[i].num_sensor; j++) {
+			s_index = tc[i].sensor_map[j];
+
+			msr_raw = readl(LVTSMSR0_0 + base + 0x4 * j) & MRS_RAW_MASK;
+			current_temp = lvts_raw_to_temp(&lvts_data->coeff, msr_raw);
+
+			if (msr_raw == 0)
+				current_temp = THERMAL_TEMP_INVALID;
+
+			max_temp = max(max_temp, current_temp);
+
+			lvts_data->sen_data[s_index].msr_raw = msr_raw;
+			lvts_data->sen_data[s_index].temp = current_temp;
+		}
+	}
+
+	return max_temp;
+}
+
+static int soc_temp_lvts_read_temp(void *data, int *temperature)
+{
+	struct soc_temp_tz *lvts_tz = (struct soc_temp_tz *)data;
+	struct lvts_data *lvts_data = lvts_tz->lvts_data;
+
+	if (lvts_tz->id == 0)
+		*temperature = lvts_read_all_tc_temperature(lvts_data);
+	else if (lvts_tz->id - 1 < lvts_data->num_sensor)
+		*temperature = lvts_data->sen_data[lvts_tz->id - 1].temp;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static const struct thermal_zone_of_device_ops soc_temp_lvts_ops = {
+	.get_temp = soc_temp_lvts_read_temp,
+};
+
+static void lvts_write_device(struct lvts_data *lvts_data, unsigned int data,
+			      int tc_id)
+{
+	void __iomem *base;
+
+	base = GET_BASE_ADDR(tc_id);
+
+	writel(data, LVTS_CONFIG_0 + base);
+
+	usleep_range(5, 15);
+}
+
+static unsigned int lvts_read_device(struct lvts_data *lvts_data,
+				     unsigned int reg_idx, int tc_id)
+{
+	struct device *dev = lvts_data->dev;
+	void __iomem *base;
+	unsigned int data;
+	int ret;
+
+	base = GET_BASE_ADDR(tc_id);
+	writel(READ_DEVICE_REG(reg_idx), LVTS_CONFIG_0 + base);
+
+	ret = readl_poll_timeout(LVTS_CONFIG_0 + base, data,
+				 !(data & DEVICE_ACCESS_STARTUS),
+				 2, 200);
+	if (ret)
+		dev_err(dev,
+			"Error: LVTS %d DEVICE_ACCESS_START didn't ready\n", tc_id);
+
+	data = readl(LVTSRDATA0_0 + base);
+
+	return data;
+}
+
+static void wait_all_tc_sensing_point_idle(struct lvts_data *lvts_data)
+{
+	struct device *dev = lvts_data->dev;
+	unsigned int mask, error_code, is_error;
+	void __iomem *base;
+	int i, cnt, ret;
+
+	mask = BIT(10) | BIT(7) | BIT(0);
+
+	for (cnt = 0; cnt < 2; cnt++) {
+		is_error = 0;
+		for (i = 0; i < lvts_data->num_tc; i++) {
+			base = GET_BASE_ADDR(i);
+			ret = readl_poll_timeout(LVTSMSRCTL1_0 + base, error_code,
+						 !(error_code & mask), 2, 200);
+			/*
+			 * Error code
+			 * 000: IDLE
+			 * 001: Write transaction
+			 * 010: Waiting for read after Write
+			 * 011: Disable Continue fetching on Device
+			 * 100: Read transaction
+			 * 101: Set Device special Register for Voltage threshold
+			 * 111: Set TSMCU number for Fetch
+			 */
+			error_code = ((error_code & BIT(10)) >> 8) +
+				((error_code & BIT(7)) >> 6) +
+				(error_code & BIT(0));
+
+			if (ret)
+				dev_err(dev,
+					"Error LVTS %d sensing points aren't idle, error_code %d\n",
+					i, error_code);
+
+			if (error_code != 0)
+				is_error = 1;
+		}
+
+		if (is_error == 0)
+			break;
+	}
+}
+
+static void lvts_reset(struct lvts_data *lvts_data)
+{
+	int i;
+
+	for (i = 0; i < lvts_data->num_domain; i++) {
+		if (lvts_data->domain[i].reset)
+			reset_control_assert(lvts_data->domain[i].reset);
+
+		if (lvts_data->domain[i].reset)
+			reset_control_deassert(lvts_data->domain[i].reset);
+	}
+}
+
+static void device_identification(struct lvts_data *lvts_data)
+{
+	struct device *dev = lvts_data->dev;
+	unsigned int i, data;
+	void __iomem *base;
+
+	for (i = 0; i < lvts_data->num_tc; i++) {
+		base = GET_BASE_ADDR(i);
+
+		writel(ENABLE_LVTS_CTRL_CLK, LVTSCLKEN_0 + base);
+
+		lvts_write_device(lvts_data, RESET_ALL_DEVICES, i);
+
+		lvts_write_device(lvts_data, READ_BACK_DEVICE_ID, i);
+
+		/* Check LVTS device ID */
+		data = (readl(LVTS_ID_0 + base) & GENMASK(7, 0));
+		if (data != (0x81 + i))
+			dev_err(dev, "LVTS_TC_%d, Device ID should be 0x%x, but 0x%x\n",
+				i, (0x81 + i), data);
+	}
+}
+
+static void disable_all_sensing_points(struct lvts_data *lvts_data)
+{
+	unsigned int i;
+	void __iomem *base;
+
+	for (i = 0; i < lvts_data->num_tc; i++) {
+		base = GET_BASE_ADDR(i);
+		writel(DISABLE_SENSING_POINT, LVTSMONCTL0_0 + base);
+	}
+}
+
+static void enable_all_sensing_points(struct lvts_data *lvts_data)
+{
+	struct device *dev = lvts_data->dev;
+	struct tc_settings *tc = lvts_data->tc;
+	unsigned int i, num;
+	void __iomem *base;
+
+	for (i = 0; i < lvts_data->num_tc; i++) {
+		base = GET_BASE_ADDR(i);
+		num = tc[i].num_sensor;
+
+		if (num > ALL_SENSING_POINTS) {
+			dev_err(dev,
+				"%s, LVTS%d, illegal number of sensors: %d\n",
+				__func__, i, tc[i].num_sensor);
+			continue;
+		}
+
+		writel(ENABLE_SENSING_POINT(num), LVTSMONCTL0_0 + base);
+	}
+}
+
+static void set_polling_speed(struct lvts_data *lvts_data, int tc_id)
+{
+	struct device *dev = lvts_data->dev;
+	struct tc_settings *tc = lvts_data->tc;
+	unsigned int lvts_mon_ctl_1, lvts_mon_ctl_2;
+	void __iomem *base;
+
+	base = GET_BASE_ADDR(tc_id);
+
+	lvts_mon_ctl_1 = ((tc[tc_id].tc_speed.group_interval_delay << 20) & GENMASK(29, 20)) |
+			(tc[tc_id].tc_speed.period_unit & GENMASK(9, 0));
+	lvts_mon_ctl_2 = ((tc[tc_id].tc_speed.filter_interval_delay << 16) & GENMASK(25, 16)) |
+			(tc[tc_id].tc_speed.sensor_interval_delay & GENMASK(9, 0));
+	/*
+	 * Clock source of LVTS thermal controller is 26MHz.
+	 * Period unit is a base for all interval delays
+	 * All interval delays must multiply it to convert a setting to time.
+	 * Filter interval delay is a delay between two samples of the same sensor
+	 * Sensor interval delay is a delay between two samples of differnet sensors
+	 * Group interval delay is a delay between different rounds.
+	 * For example:
+	 *     If Period unit = C, filter delay = 1, sensor delay = 2, group delay = 1,
+	 *     and two sensors, TS1 and TS2, are in a LVTS thermal controller
+	 *     and then
+	 *     Period unit = C * 1/26M * 256 = 12 * 38.46ns * 256 = 118.149us
+	 *     Filter interval delay = 1 * Period unit = 118.149us
+	 *     Sensor interval delay = 2 * Period unit = 236.298us
+	 *     Group interval delay = 1 * Period unit = 118.149us
+	 *
+	 *     TS1    TS1 ... TS1    TS2    TS2 ... TS2    TS1...
+	 *        <--> Filter interval delay
+	 *                       <--> Sensor interval delay
+	 *                                             <--> Group interval delay
+	 */
+	writel(lvts_mon_ctl_1, LVTSMONCTL1_0 + base);
+	writel(lvts_mon_ctl_2, LVTSMONCTL2_0 + base);
+
+	dev_info(dev, "%s %d, LVTSMONCTL1_0= 0x%x,LVTSMONCTL2_0= 0x%x\n",
+		 __func__, tc_id, readl(LVTSMONCTL1_0 + base),
+		 readl(LVTSMONCTL2_0 + base));
+}
+
+static void set_hw_filter(struct lvts_data *lvts_data, int tc_id)
+{
+	struct device *dev = lvts_data->dev;
+	struct tc_settings *tc = lvts_data->tc;
+	unsigned int option;
+	void __iomem *base;
+
+	base = GET_BASE_ADDR(tc_id);
+	option = tc[tc_id].hw_filter & 0x7;
+	/* hw filter
+	 * 000: Get one sample
+	 * 001: Get 2 samples and average them
+	 * 010: Get 4 samples, drop max and min, then average the rest of 2 samples
+	 * 011: Get 6 samples, drop max and min, then average the rest of 4 samples
+	 * 100: Get 10 samples, drop max and min, then average the rest of 8 samples
+	 * 101: Get 18 samples, drop max and min, then average the rest of 16 samples
+	 */
+	option = (option << 9) | (option << 6) | (option << 3) | option;
+
+	writel(option, LVTSMSRCTL0_0 + base);
+	dev_info(dev, "%s %d, LVTSMSRCTL0_0= 0x%x\n",
+		 __func__, tc_id, readl(LVTSMSRCTL0_0 + base));
+}
+
+static int get_dominator_index(struct lvts_data *lvts_data, int tc_id)
+{
+	struct device *dev = lvts_data->dev;
+	struct tc_settings *tc = lvts_data->tc;
+	int d_index;
+
+	if (tc[tc_id].dominator_sensing_point == ALL_SENSING_POINTS) {
+		d_index = ALL_SENSING_POINTS;
+	} else if (tc[tc_id].dominator_sensing_point <
+		tc[tc_id].num_sensor){
+		d_index = tc[tc_id].dominator_sensing_point;
+	} else {
+		dev_err(dev,
+			"Error: LVTS%d, dominator_sensing_point= %d should smaller than num_sensor= %d\n",
+			tc_id, tc[tc_id].dominator_sensing_point,
+			tc[tc_id].num_sensor);
+
+		dev_err(dev, "Use the sensing point 0 as the dominated sensor\n");
+		d_index = SENSING_POINT0;
+	}
+
+	return d_index;
+}
+
+static void disable_hw_reboot_interrupt(struct lvts_data *lvts_data, int tc_id)
+{
+	unsigned int temp;
+	void __iomem *base;
+
+	base = GET_BASE_ADDR(tc_id);
+
+	/* LVTS thermal controller has two interrupts for thermal HW reboot
+	 * One is for AP SW and the other is for RGU
+	 * The interrupt of AP SW can turn off by a bit of a register, but
+	 * the other for RGU cannot.
+	 * To prevent rebooting device accidentally, we are going to add
+	 * a huge offset to LVTS and make LVTS always report extremely low
+	 * temperature.
+	 */
+
+	/* After adding the huge offset 0x3FFF, LVTS alawys adds the
+	 * offset to MSR_RAW.
+	 * When MSR_RAW is larger, SW will convert lower temperature/
+	 */
+	temp = readl(LVTSPROTCTL_0 + base);
+	writel(temp | 0x3FFF, LVTSPROTCTL_0 + base);
+
+	/* Disable the interrupt of AP SW */
+	temp = readl(LVTSMONINT_0 + base);
+	writel(temp & ~(STAGE3_INT_EN), LVTSMONINT_0 + base);
+}
+
+static void enable_hw_reboot_interrupt(struct lvts_data *lvts_data, int tc_id)
+{
+	unsigned int temp;
+	void __iomem *base;
+
+	base = GET_BASE_ADDR(tc_id);
+
+	/* Enable the interrupt of AP SW */
+	temp = readl(LVTSMONINT_0 + base);
+	writel(temp | STAGE3_INT_EN, LVTSMONINT_0 + base);
+	/* Clear the offset */
+	temp = readl(LVTSPROTCTL_0 + base);
+	writel(temp & ~PROTOFFSET, LVTSPROTCTL_0 + base);
+}
+
+static void set_tc_hw_reboot_threshold(struct lvts_data *lvts_data,
+				       int trip_point, int tc_id)
+{
+	struct device *dev = lvts_data->dev;
+	unsigned int msr_raw, temp, config, d_index;
+	void __iomem *base;
+
+	base = GET_BASE_ADDR(tc_id);
+	d_index = get_dominator_index(lvts_data, tc_id);
+
+	dev_info(dev, "%s: LVTS%d, the dominator sensing point= %d\n",
+		 __func__, tc_id, d_index);
+
+	disable_hw_reboot_interrupt(lvts_data, tc_id);
+
+	temp = readl(LVTSPROTCTL_0 + base);
+	if (d_index == ALL_SENSING_POINTS) {
+		/* Maximum of 4 sensing points */
+		config = (0x1 << 16);
+		writel(config | temp, LVTSPROTCTL_0 + base);
+	} else {
+		/* Select protection sensor */
+		config = ((d_index << 2) + 0x2) << 16;
+		writel(config | temp, LVTSPROTCTL_0 + base);
+	}
+
+	msr_raw = lvts_temp_to_raw(&lvts_data->coeff, trip_point);
+	writel(msr_raw, LVTSPROTTC_0 + base);
+
+	enable_hw_reboot_interrupt(lvts_data, tc_id);
+}
+
+static void set_all_tc_hw_reboot(struct lvts_data *lvts_data)
+{
+	struct tc_settings *tc = lvts_data->tc;
+	int i, trip_point;
+
+	for (i = 0; i < lvts_data->num_tc; i++) {
+		trip_point = tc[i].hw_reboot_trip_point;
+
+		if (tc[i].num_sensor == 0)
+			continue;
+
+		if (trip_point == DISABLE_THERMAL_HW_REBOOT)
+			continue;
+
+		set_tc_hw_reboot_threshold(lvts_data, trip_point, i);
+	}
+}
+
+static int lvts_init(struct lvts_data *lvts_data)
+{
+	struct platform_ops *ops = &lvts_data->ops;
+	struct device *dev = lvts_data->dev;
+	int ret;
+
+	ret = clk_prepare_enable(lvts_data->clk);
+	if (ret) {
+		dev_err(dev,
+			"Error: Failed to enable lvts controller clock: %d\n",
+			ret);
+		return ret;
+	}
+
+	lvts_reset(lvts_data);
+
+	device_identification(lvts_data);
+	if (ops->device_enable_and_init)
+		ops->device_enable_and_init(lvts_data);
+
+	if (IS_ENABLE(FEATURE_DEVICE_AUTO_RCK)) {
+		if (ops->device_enable_auto_rck)
+			ops->device_enable_auto_rck(lvts_data);
+	} else {
+		if (ops->device_read_count_rc_n)
+			ops->device_read_count_rc_n(lvts_data);
+	}
+
+	if (ops->set_cal_data)
+		ops->set_cal_data(lvts_data);
+
+	disable_all_sensing_points(lvts_data);
+	wait_all_tc_sensing_point_idle(lvts_data);
+	if (ops->init_controller)
+		ops->init_controller(lvts_data);
+	enable_all_sensing_points(lvts_data);
+
+	set_all_tc_hw_reboot(lvts_data);
+
+	return 0;
+}
+
+static int prepare_calibration_data(struct lvts_data *lvts_data)
+{
+	struct device *dev = lvts_data->dev;
+	struct sensor_cal_data *cal_data = &lvts_data->cal_data;
+	struct platform_ops *ops = &lvts_data->ops;
+	int i, offset, size;
+	char buffer[512];
+
+	cal_data->count_r = devm_kcalloc(dev, lvts_data->num_sensor,
+					 sizeof(*cal_data->count_r), GFP_KERNEL);
+	if (!cal_data->count_r)
+		return -ENOMEM;
+
+	cal_data->count_rc = devm_kcalloc(dev, lvts_data->num_sensor,
+					  sizeof(*cal_data->count_rc), GFP_KERNEL);
+	if (!cal_data->count_rc)
+		return -ENOMEM;
+
+	if (ops->efuse_to_cal_data)
+		ops->efuse_to_cal_data(lvts_data);
+
+	cal_data->use_fake_efuse = 1;
+	if (cal_data->golden_temp != 0) {
+		cal_data->use_fake_efuse = 0;
+	} else {
+		for (i = 0; i < lvts_data->num_sensor; i++) {
+			if (cal_data->count_r[i] != 0 ||
+			    cal_data->count_rc[i] != 0) {
+				cal_data->use_fake_efuse = 0;
+				break;
+			}
+		}
+	}
+
+	if (cal_data->use_fake_efuse) {
+		/* It means all efuse data are equal to 0 */
+		dev_err(dev,
+			"[lvts_cal] This sample is not calibrated, fake !!\n");
+
+		cal_data->golden_temp = cal_data->default_golden_temp;
+		for (i = 0; i < lvts_data->num_sensor; i++) {
+			cal_data->count_r[i] = cal_data->default_count_r;
+			cal_data->count_rc[i] = cal_data->default_count_rc;
+		}
+	}
+
+	lvts_data->coeff.golden_temp = cal_data->golden_temp;
+
+	dev_info(dev, "[lvts_cal] golden_temp = %d\n", cal_data->golden_temp);
+
+	size = sizeof(buffer);
+	offset = snprintf(buffer, size, "[lvts_cal] num:g_count:g_count_rc ");
+	for (i = 0; i < lvts_data->num_sensor; i++)
+		offset += snprintf(buffer + offset, size - offset, "%d:%d:%d ",
+				   i, cal_data->count_r[i], cal_data->count_rc[i]);
+
+	buffer[offset] = '\0';
+	dev_info(dev, "%s\n", buffer);
+
+	return 0;
+}
+
+static int get_calibration_data(struct lvts_data *lvts_data)
+{
+	struct device *dev = lvts_data->dev;
+	char cell_name[8];
+	struct nvmem_cell *cell;
+	u32 *buf;
+	size_t len;
+	int i, j, index = 0, ret;
+
+	lvts_data->efuse = devm_kcalloc(dev, lvts_data->num_efuse_addr,
+					sizeof(*lvts_data->efuse), GFP_KERNEL);
+	if (!lvts_data->efuse)
+		return -ENOMEM;
+
+	for (i = 0; i < lvts_data->num_efuse_block; i++) {
+		snprintf(cell_name, sizeof(cell_name), "e_data%d", i + 1);
+		cell = nvmem_cell_get(dev, cell_name);
+		if (IS_ERR(cell)) {
+			dev_err(dev, "Error: Failed to get nvmem cell %s\n", cell_name);
+			return PTR_ERR(cell);
+		}
+
+		buf = (u32 *)nvmem_cell_read(cell, &len);
+		nvmem_cell_put(cell);
+
+		if (IS_ERR(buf))
+			return PTR_ERR(buf);
+
+		for (j = 0; j < (len / sizeof(u32)); j++) {
+			if (index >= lvts_data->num_efuse_addr) {
+				dev_err(dev, "Array efuse is going to overflow");
+				kfree(buf);
+				return -EINVAL;
+			}
+
+			lvts_data->efuse[index] = buf[j];
+			index++;
+		}
+
+		kfree(buf);
+	}
+
+	ret = prepare_calibration_data(lvts_data);
+
+	return ret;
+}
+
+static int of_update_lvts_data(struct lvts_data *lvts_data,
+			       struct platform_device *pdev)
+{
+	struct device *dev = lvts_data->dev;
+	struct power_domain *domain;
+	struct resource *res;
+	unsigned int i;
+	int ret;
+
+	lvts_data->clk = devm_clk_get(dev, "lvts_clk");
+	if (IS_ERR(lvts_data->clk))
+		return PTR_ERR(lvts_data->clk);
+
+	domain = devm_kcalloc(dev, lvts_data->num_domain, sizeof(*domain), GFP_KERNEL);
+	if (!domain)
+		return -ENOMEM;
+
+	for (i = 0; i < lvts_data->num_domain; i++) {
+		/* Get base address */
+		res = platform_get_resource(pdev, IORESOURCE_MEM, i);
+		if (!res) {
+			dev_err(dev, "No IO resource, index %d\n", i);
+			return -ENXIO;
+		}
+
+		domain[i].base = devm_ioremap_resource(dev, res);
+		if (IS_ERR(domain[i].base)) {
+			dev_err(dev, "Failed to remap io, index %d\n", i);
+			return PTR_ERR(domain[i].base);
+		}
+
+		/* Get interrupt number */
+		res = platform_get_resource(pdev, IORESOURCE_IRQ, i);
+		if (!res) {
+			dev_err(dev, "No irq resource, index %d\n", i);
+			return -EINVAL;
+		}
+		domain[i].irq_num = res->start;
+
+		/* Get reset control */
+		domain[i].reset = devm_reset_control_get_by_index(dev, i);
+		if (IS_ERR(domain[i].reset)) {
+			dev_err(dev, "Failed to get, index %d\n", i);
+			return PTR_ERR(domain[i].reset);
+		}
+	}
+
+	lvts_data->domain = domain;
+
+	lvts_data->sen_data = devm_kcalloc(dev, lvts_data->num_sensor,
+					   sizeof(*lvts_data->sen_data), GFP_KERNEL);
+	if (!lvts_data->sen_data)
+		return -ENOMEM;
+
+	ret = get_calibration_data(lvts_data);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static void lvts_device_close(struct lvts_data *lvts_data)
+{
+	unsigned int i;
+	void __iomem *base;
+
+	for (i = 0; i < lvts_data->num_tc; i++) {
+		base = GET_BASE_ADDR(i);
+		lvts_write_device(lvts_data, RESET_ALL_DEVICES, i);
+		writel(DISABLE_LVTS_CTRL_CLK, LVTSCLKEN_0 + base);
+	}
+}
+
+static void lvts_close(struct lvts_data *lvts_data)
+{
+	disable_all_sensing_points(lvts_data);
+	wait_all_tc_sensing_point_idle(lvts_data);
+	lvts_device_close(lvts_data);
+	clk_disable_unprepare(lvts_data->clk);
+}
+
+static void tc_irq_handler(struct lvts_data *lvts_data, int tc_id)
+{
+	struct device *dev = lvts_data->dev;
+	unsigned int ret = 0;
+	void __iomem *base;
+
+	base = GET_BASE_ADDR(tc_id);
+
+	ret = readl(LVTSMONINTSTS_0 + base);
+	/* Write back to clear interrupt status */
+	writel(ret, LVTSMONINTSTS_0 + base);
+
+	dev_info(dev, "[Thermal IRQ] LVTS thermal controller %d, LVTSMONINTSTS=0x%08x\n",
+		 tc_id, ret);
+
+	if (ret & THERMAL_PROTECTION_STAGE_3)
+		dev_info(dev,
+			 "[Thermal IRQ]: Thermal protection stage 3 interrupt triggered\n");
+}
+
+static irqreturn_t irq_handler(int irq, void *dev_id)
+{
+	struct lvts_data *lvts_data = (struct lvts_data *)dev_id;
+	struct device *dev = lvts_data->dev;
+	struct tc_settings *tc = lvts_data->tc;
+	unsigned int i, *irq_bitmap;
+	void __iomem *base;
+
+	irq_bitmap = kcalloc(lvts_data->num_domain, sizeof(*irq_bitmap), GFP_ATOMIC);
+
+	if (!irq_bitmap)
+		return IRQ_NONE;
+
+	for (i = 0; i < lvts_data->num_domain; i++) {
+		base = lvts_data->domain[i].base;
+		irq_bitmap[i] = readl(THERMINTST + base);
+		dev_info(dev, "%s : THERMINTST = 0x%x\n", __func__, irq_bitmap[i]);
+	}
+
+	for (i = 0; i < lvts_data->num_tc; i++) {
+		if ((irq_bitmap[tc[i].domain_index] & tc[i].irq_bit) == 0)
+			tc_irq_handler(lvts_data, i);
+	}
+
+	kfree(irq_bitmap);
+
+	return IRQ_HANDLED;
+}
+
+static int lvts_register_irq_handler(struct lvts_data *lvts_data)
+{
+	struct device *dev = lvts_data->dev;
+	unsigned int i;
+	int ret;
+
+	for (i = 0; i < lvts_data->num_domain; i++) {
+		ret = devm_request_irq(dev, lvts_data->domain[i].irq_num, irq_handler,
+				       IRQF_TRIGGER_HIGH, "mtk_lvts", lvts_data);
+
+		if (ret) {
+			dev_err(dev, "Failed to register LVTS IRQ, ret %d, domain %d irq_num %d\n",
+				ret, i, lvts_data->domain[i].irq_num);
+			lvts_close(lvts_data);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int lvts_register_thermal_zones(struct lvts_data *lvts_data)
+{
+	struct device *dev = lvts_data->dev;
+	struct thermal_zone_device *tzdev;
+	struct soc_temp_tz *lvts_tz;
+	int i, ret;
+
+	for (i = 0; i < lvts_data->num_sensor + 1; i++) {
+		lvts_tz = devm_kzalloc(dev, sizeof(*lvts_tz), GFP_KERNEL);
+		if (!lvts_tz) {
+			lvts_close(lvts_data);
+			return -ENOMEM;
+		}
+
+		lvts_tz->id = i;
+		lvts_tz->lvts_data = lvts_data;
+
+		tzdev = devm_thermal_zone_of_sensor_register(dev, lvts_tz->id,
+							     lvts_tz, &soc_temp_lvts_ops);
+
+		if (IS_ERR(tzdev)) {
+			if (lvts_tz->id != 0)
+				return 0;
+
+			ret = PTR_ERR(tzdev);
+			dev_err(dev, "Error: Failed to register lvts tz %d, ret = %d\n",
+				lvts_tz->id, ret);
+			lvts_close(lvts_data);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int lvts_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct lvts_data *lvts_data;
+	int ret;
+
+	lvts_data = (struct lvts_data *)of_device_get_match_data(dev);
+
+	if (!lvts_data)	{
+		dev_err(dev, "Error: Failed to get lvts platform data\n");
+		return -ENODATA;
+	}
+
+	lvts_data->dev = &pdev->dev;
+
+	ret = of_update_lvts_data(lvts_data, pdev);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, lvts_data);
+
+	ret = lvts_init(lvts_data);
+	if (ret)
+		return ret;
+
+	ret = lvts_register_irq_handler(lvts_data);
+	if (ret)
+		return ret;
+
+	ret = lvts_register_thermal_zones(lvts_data);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int lvts_remove(struct platform_device *pdev)
+{
+	struct lvts_data *lvts_data;
+
+	lvts_data = (struct lvts_data *)platform_get_drvdata(pdev);
+
+	lvts_close(lvts_data);
+
+	return 0;
+}
+
+static int lvts_suspend(struct platform_device *pdev, pm_message_t state)
+{
+	struct lvts_data *lvts_data;
+
+	lvts_data = (struct lvts_data *)platform_get_drvdata(pdev);
+
+	lvts_close(lvts_data);
+
+	return 0;
+}
+
+static int lvts_resume(struct platform_device *pdev)
+{
+	int ret;
+	struct lvts_data *lvts_data;
+
+	lvts_data = (struct lvts_data *)platform_get_drvdata(pdev);
+
+	ret = lvts_init(lvts_data);
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+/*==================================================
+ * LVTS v4 common code
+ *==================================================
+ */
+static void device_enable_and_init_v4(struct lvts_data *lvts_data)
+{
+	unsigned int i;
+
+	for (i = 0; i < lvts_data->num_tc; i++) {
+		lvts_write_device(lvts_data, STOP_COUNTING_V4, i);
+		lvts_write_device(lvts_data, SET_RG_TSFM_LPDLY_V4, i);
+		lvts_write_device(lvts_data, SET_COUNTING_WINDOW_20US1_V4, i);
+		lvts_write_device(lvts_data, SET_COUNTING_WINDOW_20US2_V4, i);
+		lvts_write_device(lvts_data, TSV2F_CHOP_CKSEL_AND_TSV2F_EN_V4, i);
+		lvts_write_device(lvts_data, TSBG_DEM_CKSEL_X_TSBG_CHOP_EN_V4, i);
+		lvts_write_device(lvts_data, SET_TS_RSV_V4, i);
+		lvts_write_device(lvts_data, SET_TS_EN_V4, i);
+		lvts_write_device(lvts_data, TOGGLE_RG_TSV2F_VCO_RST1_V4, i);
+		lvts_write_device(lvts_data, TOGGLE_RG_TSV2F_VCO_RST2_V4, i);
+	}
+
+	lvts_data->counting_window_us = 20;
+}
+
+static void device_enable_auto_rck_v4(struct lvts_data *lvts_data)
+{
+	unsigned int i;
+
+	for (i = 0; i < lvts_data->num_tc; i++)
+		lvts_write_device(lvts_data, SET_LVTS_AUTO_RCK_V4, i);
+}
+
+static int device_read_count_rc_n_v4(struct lvts_data *lvts_data)
+{
+	/* Resistor-Capacitor Calibration */
+	/* count_RC_N: count RC now */
+	struct device *dev = lvts_data->dev;
+	struct tc_settings *tc = lvts_data->tc;
+	struct sensor_cal_data *cal_data = &lvts_data->cal_data;
+	unsigned int offset, size, s_index, data;
+	void __iomem *base;
+	int ret, i, j;
+	char buffer[512];
+
+	cal_data->count_rc_now = devm_kcalloc(dev, lvts_data->num_sensor,
+					      sizeof(*cal_data->count_rc_now), GFP_KERNEL);
+	if (!cal_data->count_rc_now)
+		return -ENOMEM;
+
+	for (i = 0; i < lvts_data->num_tc; i++) {
+		base = GET_BASE_ADDR(i);
+		for (j = 0; j < tc[i].num_sensor; j++) {
+			s_index = tc[i].sensor_map[j];
+
+			lvts_write_device(lvts_data, SELECT_SENSOR_RCK_V4(j), i);
+			lvts_write_device(lvts_data, SET_DEVICE_SINGLE_MODE_V4, i);
+			usleep_range(10, 20);
+
+			lvts_write_device(lvts_data, KICK_OFF_RCK_COUNTING_V4, i);
+			usleep_range(30, 40);
+
+			ret = readl_poll_timeout(LVTS_CONFIG_0 + base, data,
+						 !(data & DEVICE_SENSING_STATUS), 2, 200);
+			if (ret)
+				dev_err(dev,
+					"Error: LVTS %d DEVICE_SENSING_STATUS didn't ready\n", i);
+
+			data = lvts_read_device(lvts_data, 0x00, i);
+
+			cal_data->count_rc_now[s_index] = (data & GENMASK(23, 0));
+		}
+
+		/* Recover Setting for Normal Access on
+		 * temperature fetch
+		 */
+		lvts_write_device(lvts_data, SET_SENSOR_NO_RCK_V4, i);
+		lvts_write_device(lvts_data, SET_DEVICE_LOW_POWER_SINGLE_MODE_V4, i);
+	}
+
+	size = sizeof(buffer);
+	offset = snprintf(buffer, size, "[COUNT_RC_NOW] ");
+	for (i = 0; i < lvts_data->num_sensor; i++)
+		offset += snprintf(buffer + offset, size - offset, "%d:%d ",
+				   i, cal_data->count_rc_now[i]);
+
+	buffer[offset] = '\0';
+	dev_info(dev, "%s\n", buffer);
+
+	return 0;
+}
+
+static void set_calibration_data_v4(struct lvts_data *lvts_data)
+{
+	struct tc_settings *tc = lvts_data->tc;
+	struct sensor_cal_data *cal_data = &lvts_data->cal_data;
+	unsigned int i, j, s_index, e_data;
+	void __iomem *base;
+
+	for (i = 0; i < lvts_data->num_tc; i++) {
+		base = GET_BASE_ADDR(i);
+
+		for (j = 0; j < tc[i].num_sensor; j++) {
+			s_index = tc[i].sensor_map[j];
+			if (IS_ENABLE(FEATURE_DEVICE_AUTO_RCK))
+				e_data = cal_data->count_r[s_index];
+			else
+				e_data = (((unsigned long long)
+					cal_data->count_rc_now[s_index]) *
+					cal_data->count_r[s_index]) >> 14;
+
+			writel(e_data, LVTSEDATA00_0 + base + 0x4 * j);
+		}
+	}
+}
+
+static void init_controller_v4(struct lvts_data *lvts_data)
+{
+	struct device *dev = lvts_data->dev;
+	unsigned int i;
+	void __iomem *base;
+
+	for (i = 0; i < lvts_data->num_tc; i++) {
+		base = GET_BASE_ADDR(i);
+
+		lvts_write_device(lvts_data, SET_DEVICE_LOW_POWER_SINGLE_MODE_V4, i);
+
+		writel(SET_SENSOR_INDEX, LVTSTSSEL_0 + base);
+		writel(SET_CALC_SCALE_RULES, LVTSCALSCALE_0 + base);
+
+		set_polling_speed(lvts_data, i);
+		set_hw_filter(lvts_data, i);
+
+		dev_info(dev, "lvts%d: read all %d sensors in %d us, one in %d us\n",
+			 i, GET_TC_SENSOR_NUM(i), GROUP_LATENCY_US(i), SENSOR_LATENCY_US(i));
+	}
+}
+
+/*==================================================
+ * LVTS MT6873
+ *==================================================
+ */
+
+#define MT6873_NUM_LVTS (ARRAY_SIZE(mt6873_tc_settings))
+
+enum mt6873_lvts_domain {
+	MT6873_AP_DOMAIN,
+	MT6873_MCU_DOMAIN,
+	MT6873_NUM_DOMAIN
+};
+
+enum mt6873_lvts_sensor_enum {
+	MT6873_TS1_0,
+	MT6873_TS1_1,
+	MT6873_TS2_0,
+	MT6873_TS2_1,
+	MT6873_TS3_0,
+	MT6873_TS3_1,
+	MT6873_TS3_2,
+	MT6873_TS3_3,
+	MT6873_TS4_0,
+	MT6873_TS4_1,
+	MT6873_TS5_0,
+	MT6873_TS5_1,
+	MT6873_TS6_0,
+	MT6873_TS6_1,
+	MT6873_TS7_0,
+	MT6873_TS7_1,
+	MT6873_TS7_2,
+	MT6873_NUM_TS
+};
+
+static void mt6873_efuse_to_cal_data(struct lvts_data *lvts_data)
+{
+	struct sensor_cal_data *cal_data = &lvts_data->cal_data;
+
+	cal_data->golden_temp = GET_CAL_DATA_BITMASK(0, 31, 24);
+	cal_data->count_r[MT6873_TS1_0] = GET_CAL_DATA_BITMASK(1, 23, 0);
+	cal_data->count_r[MT6873_TS1_1] = GET_CAL_DATA_BITMASK(2, 23, 0);
+	cal_data->count_r[MT6873_TS2_0] = GET_CAL_DATA_BITMASK(3, 23, 0);
+	cal_data->count_r[MT6873_TS2_1] = GET_CAL_DATA_BITMASK(4, 23, 0);
+	cal_data->count_r[MT6873_TS3_0] = GET_CAL_DATA_BITMASK(5, 23, 0);
+	cal_data->count_r[MT6873_TS3_1] = GET_CAL_DATA_BITMASK(6, 23, 0);
+	cal_data->count_r[MT6873_TS3_2] = GET_CAL_DATA_BITMASK(7, 23, 0);
+	cal_data->count_r[MT6873_TS3_3] = GET_CAL_DATA_BITMASK(8, 23, 0);
+	cal_data->count_r[MT6873_TS4_0] = GET_CAL_DATA_BITMASK(9, 23, 0);
+	cal_data->count_r[MT6873_TS4_1] = GET_CAL_DATA_BITMASK(10, 23, 0);
+	cal_data->count_r[MT6873_TS5_0] = GET_CAL_DATA_BITMASK(11, 23, 0);
+	cal_data->count_r[MT6873_TS5_1] = GET_CAL_DATA_BITMASK(12, 23, 0);
+	cal_data->count_r[MT6873_TS6_0] = GET_CAL_DATA_BITMASK(13, 23, 0);
+	cal_data->count_r[MT6873_TS6_1] = GET_CAL_DATA_BITMASK(14, 23, 0);
+	cal_data->count_r[MT6873_TS7_0] = GET_CAL_DATA_BITMASK(15, 23, 0);
+	cal_data->count_r[MT6873_TS7_1] = GET_CAL_DATA_BITMASK(16, 23, 0);
+	cal_data->count_r[MT6873_TS7_2] = GET_CAL_DATA_BITMASK(17, 23, 0);
+
+	cal_data->count_rc[MT6873_TS1_0] = GET_CAL_DATA_BITMASK(21, 23, 0);
+
+	cal_data->count_rc[MT6873_TS2_0] = (GET_CAL_DATA_BITMASK(1, 31, 24) << 16) +
+					   (GET_CAL_DATA_BITMASK(2, 31, 24) << 8) +
+					    GET_CAL_DATA_BITMASK(3, 31, 24);
+
+	cal_data->count_rc[MT6873_TS3_0] = (GET_CAL_DATA_BITMASK(4, 31, 24) << 16) +
+					   (GET_CAL_DATA_BITMASK(5, 31, 24) << 8) +
+					    GET_CAL_DATA_BITMASK(6, 31, 24);
+
+	cal_data->count_rc[MT6873_TS4_0] = (GET_CAL_DATA_BITMASK(7, 31, 24) << 16) +
+					   (GET_CAL_DATA_BITMASK(8, 31, 24) << 8) +
+					    GET_CAL_DATA_BITMASK(9, 31, 24);
+
+	cal_data->count_rc[MT6873_TS5_0] = (GET_CAL_DATA_BITMASK(10, 31, 24) << 16) +
+					   (GET_CAL_DATA_BITMASK(11, 31, 24) << 8) +
+					    GET_CAL_DATA_BITMASK(12, 31, 24);
+
+	cal_data->count_rc[MT6873_TS6_0] = (GET_CAL_DATA_BITMASK(13, 31, 24) << 16) +
+					   (GET_CAL_DATA_BITMASK(14, 31, 24) << 8) +
+					    GET_CAL_DATA_BITMASK(15, 31, 24);
+
+	cal_data->count_rc[MT6873_TS7_0] = (GET_CAL_DATA_BITMASK(16, 31, 24) << 16) +
+					   (GET_CAL_DATA_BITMASK(17, 31, 24) << 8) +
+					    GET_CAL_DATA_BITMASK(18, 31, 24);
+}
+
+static struct tc_settings mt6873_tc_settings[] = {
+	[0] = {
+		.domain_index = MT6873_MCU_DOMAIN,
+		.addr_offset = 0x0,
+		.num_sensor = 2,
+		.sensor_map = {MT6873_TS1_0, MT6873_TS1_1},
+		.tc_speed = SET_TC_SPEED_IN_US(118, 118, 118, 118),
+		.hw_filter = LVTS_FILTER_2_OF_4,
+		.dominator_sensing_point = SENSING_POINT1,
+		.hw_reboot_trip_point = 117000,
+		.irq_bit = BIT(3),
+	},
+	[1] = {
+		.domain_index = MT6873_MCU_DOMAIN,
+		.addr_offset = 0x100,
+		.num_sensor = 2,
+		.sensor_map = {MT6873_TS2_0, MT6873_TS2_1},
+		.tc_speed = SET_TC_SPEED_IN_US(118, 118, 118, 118),
+		.hw_filter = LVTS_FILTER_2_OF_4,
+		.dominator_sensing_point = SENSING_POINT0,
+		.hw_reboot_trip_point = 117000,
+		.irq_bit = BIT(4),
+	},
+	[2] = {
+		.domain_index = MT6873_MCU_DOMAIN,
+		.addr_offset = 0x200,
+		.num_sensor = 4,
+		.sensor_map = {MT6873_TS3_0, MT6873_TS3_1, MT6873_TS3_2, MT6873_TS3_3},
+		.tc_speed = SET_TC_SPEED_IN_US(118, 118, 118, 118),
+		.hw_filter = LVTS_FILTER_2_OF_4,
+		.dominator_sensing_point = SENSING_POINT0,
+		.hw_reboot_trip_point = 117000,
+		.irq_bit = BIT(5),
+	},
+	[3] = {
+		.domain_index = MT6873_AP_DOMAIN,
+		.addr_offset = 0x0,
+		.num_sensor = 2,
+		.sensor_map = {MT6873_TS4_0, MT6873_TS4_1},
+		.tc_speed = SET_TC_SPEED_IN_US(118, 118, 118, 118),
+		.hw_filter = LVTS_FILTER_2_OF_4,
+		.dominator_sensing_point = SENSING_POINT0,
+		.hw_reboot_trip_point = 117000,
+		.irq_bit = BIT(3),
+	},
+	[4] = {
+		.domain_index = MT6873_AP_DOMAIN,
+		.addr_offset = 0x100,
+		.num_sensor = 2,
+		.sensor_map = {MT6873_TS5_0, MT6873_TS5_1},
+		.tc_speed = SET_TC_SPEED_IN_US(118, 118, 118, 118),
+		.hw_filter = LVTS_FILTER_2_OF_4,
+		.dominator_sensing_point = SENSING_POINT1,
+		.hw_reboot_trip_point = 117000,
+		.irq_bit = BIT(4),
+	},
+	[5] = {
+		.domain_index = MT6873_AP_DOMAIN,
+		.addr_offset = 0x200,
+		.num_sensor = 2,
+		.sensor_map = {MT6873_TS6_0, MT6873_TS6_1},
+		.tc_speed = SET_TC_SPEED_IN_US(118, 118, 118, 118),
+		.hw_filter = LVTS_FILTER_2_OF_4,
+		.dominator_sensing_point = SENSING_POINT1,
+		.hw_reboot_trip_point = 117000,
+		.irq_bit = BIT(5),
+	},
+	[6] = {
+		.domain_index = MT6873_AP_DOMAIN,
+		.addr_offset = 0x300,
+		.num_sensor = 3,
+		.sensor_map = {MT6873_TS7_0, MT6873_TS7_1, MT6873_TS7_2},
+		.tc_speed = SET_TC_SPEED_IN_US(118, 118, 118, 118),
+		.hw_filter = LVTS_FILTER_2_OF_4,
+		.dominator_sensing_point = SENSING_POINT2,
+		.hw_reboot_trip_point = 117000,
+		.irq_bit = BIT(6),
+	}
+};
+
+static struct lvts_data mt6873_lvts_data = {
+	.num_domain = MT6873_NUM_DOMAIN,
+	.num_tc = MT6873_NUM_LVTS,
+	.tc = mt6873_tc_settings,
+	.num_sensor = MT6873_NUM_TS,
+	.ops = {
+		.efuse_to_cal_data = mt6873_efuse_to_cal_data,
+		.device_enable_and_init = device_enable_and_init_v4,
+		.device_enable_auto_rck = device_enable_auto_rck_v4,
+		.device_read_count_rc_n = device_read_count_rc_n_v4,
+		.set_cal_data = set_calibration_data_v4,
+		.init_controller = init_controller_v4,
+	},
+	.feature_bitmap = FEATURE_DEVICE_AUTO_RCK,
+	.num_efuse_addr = 22,
+	.num_efuse_block = 1,
+	.cal_data = {
+		.default_golden_temp = 50,
+		.default_count_r = 35000,
+		.default_count_rc = 2750,
+	},
+	.coeff = {
+		.a = -250460,
+		.b = 250460,
+	},
+};
+
+/*==================================================
+ *==================================================
+ * Support chips
+ *==================================================
+ */
+static const struct of_device_id lvts_of_match[] = {
+	{
+		.compatible = "mediatek,mt6873-lvts",
+		.data = (void *)&mt6873_lvts_data,
+	},
+	{
+	},
+};
+MODULE_DEVICE_TABLE(of, lvts_of_match);
+/*==================================================*/
+static struct platform_driver soc_temp_lvts = {
+	.probe = lvts_probe,
+	.remove = lvts_remove,
+	.suspend = lvts_suspend,
+	.resume = lvts_resume,
+	.driver = {
+		.name = "mtk-soc-temp-lvts",
+		.of_match_table = lvts_of_match,
+	},
+};
+
+module_platform_driver(soc_temp_lvts);
+MODULE_AUTHOR("Yu-Chia Chang <ethan.chang at mediatek.com>");
+MODULE_AUTHOR("Michael Kao <michael.kao at mediatek.com>");
+MODULE_DESCRIPTION("Mediatek soc temperature driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/thermal/mediatek/soc_temp_lvts.h b/drivers/thermal/mediatek/soc_temp_lvts.h
new file mode 100644
index 000000000000..1d90bdec53c6
--- /dev/null
+++ b/drivers/thermal/mediatek/soc_temp_lvts.h
@@ -0,0 +1,312 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 MediaTek Inc.
+ */
+
+#ifndef __MTK_SOC_TEMP_LVTS_H__
+#define __MTK_SOC_TEMP_LVTS_H__
+
+/* LVTS HW filter settings
+ * 000: Get one sample
+ * 001: Get 2 samples and average them
+ * 010: Get 4 samples, drop max and min, then average the rest of 2 samples
+ * 011: Get 6 samples, drop max and min, then average the rest of 4 samples
+ * 100: Get 10 samples, drop max and min, then average the rest of 8 samples
+ * 101: Get 18 samples, drop max and min, then average the rest of 16 samples
+ */
+enum lvts_hw_filter {
+	LVTS_FILTER_1,
+	LVTS_FILTER_2,
+	LVTS_FILTER_2_OF_4,
+	LVTS_FILTER_4_OF_6,
+	LVTS_FILTER_8_OF_10,
+	LVTS_FILTER_16_OF_18
+};
+
+enum lvts_sensing_point {
+	SENSING_POINT0,
+	SENSING_POINT1,
+	SENSING_POINT2,
+	SENSING_POINT3,
+	ALL_SENSING_POINTS
+};
+
+/*==================================================
+ * Data structure
+ *==================================================
+ */
+struct lvts_data;
+
+struct speed_settings {
+	unsigned int period_unit;
+	unsigned int group_interval_delay;
+	unsigned int filter_interval_delay;
+	unsigned int sensor_interval_delay;
+};
+
+struct tc_settings {
+	unsigned int domain_index;
+	unsigned int addr_offset;
+	unsigned int num_sensor;
+	unsigned int sensor_map[ALL_SENSING_POINTS]; /* In sensor ID */
+	struct speed_settings tc_speed;
+	/* HW filter setting
+	 * 000: Get one sample
+	 * 001: Get 2 samples and average them
+	 * 010: Get 4 samples, drop max and min, then average the rest of 2 samples
+	 * 011: Get 6 samples, drop max and min, then average the rest of 4 samples
+	 * 100: Get 10 samples, drop max and min, then average the rest of 8 samples
+	 * 101: Get 18 samples, drop max and min, then average the rest of 16 samples
+	 */
+	unsigned int hw_filter;
+	/* Dominator_sensing point is used to select a sensing point
+	 * and reference its temperature to trigger Thermal HW Reboot
+	 * When it is ALL_SENSING_POINTS, it will select all sensing points
+	 */
+	int dominator_sensing_point;
+	int hw_reboot_trip_point; /* -274000: Disable HW reboot */
+	unsigned int irq_bit;
+};
+
+struct formula_coeff {
+	int a;
+	int b;
+	unsigned int golden_temp;
+};
+
+struct sensor_cal_data {
+	int use_fake_efuse;	/* 1: Use fake efuse, 0: Use real efuse */
+	unsigned int golden_temp;
+	unsigned int *count_r;
+	unsigned int *count_rc;
+	unsigned int *count_rc_now;
+
+	unsigned int default_golden_temp;
+	unsigned int default_count_r;
+	unsigned int default_count_rc;
+};
+
+struct platform_ops {
+	void (*efuse_to_cal_data)(struct lvts_data *lvts_data);
+	void (*device_enable_and_init)(struct lvts_data *lvts_data);
+	void (*device_enable_auto_rck)(struct lvts_data *lvts_data);
+	int (*device_read_count_rc_n)(struct lvts_data *lvts_data);
+	void (*set_cal_data)(struct lvts_data *lvts_data);
+	void (*init_controller)(struct lvts_data *lvts_data);
+};
+
+struct power_domain {
+	void __iomem *base;	/* LVTS base addresses */
+	unsigned int irq_num;	/* LVTS interrupt numbers */
+	struct reset_control *reset;
+};
+
+struct sensor_data {
+	int temp;		/* Current temperature */
+	unsigned int msr_raw;	/* MSR raw data from LVTS */
+};
+
+struct lvts_data {
+	struct device *dev;
+	struct clk *clk;
+	unsigned int num_domain;
+	struct power_domain *domain;
+
+	int num_tc;			/* Number of LVTS thermal controllers */
+	struct tc_settings *tc;
+	int counting_window_us;		/* LVTS device counting window */
+
+	int num_sensor;			/* Number of sensors in this platform */
+	struct sensor_data *sen_data;
+
+	struct platform_ops ops;
+	int feature_bitmap;		/* Show what features are enabled */
+
+	unsigned int num_efuse_addr;
+	unsigned int *efuse;
+	unsigned int num_efuse_block;	/* Number of contiguous efuse indexes */
+	struct sensor_cal_data cal_data;
+	struct formula_coeff coeff;
+};
+
+struct soc_temp_tz {
+	unsigned int id; /* if id is 0, get max temperature of all sensors */
+	struct lvts_data *lvts_data;
+};
+
+struct match_entry {
+	char	chip[32];
+	struct lvts_data *lvts_data;
+};
+
+struct lvts_match_data {
+	unsigned int hw_version;
+	struct match_entry *table;
+	void (*set_up_common_callbacks)(struct lvts_data *lvts_data);
+	struct list_head node;
+};
+
+struct lvts_id {
+	unsigned int hw_version;
+	char	chip[32];
+};
+
+/*==================================================
+ * LVTS device register
+ *==================================================
+ */
+#define RG_TSFM_DATA_0	0x00
+#define RG_TSFM_DATA_1	0x01
+#define RG_TSFM_DATA_2	0x02
+#define RG_TSFM_CTRL_0	0x03
+#define RG_TSFM_CTRL_1	0x04
+#define RG_TSFM_CTRL_2	0x05
+#define RG_TSFM_CTRL_3	0x06
+#define RG_TSFM_CTRL_4	0x07
+#define RG_TSV2F_CTRL_0	0x08
+#define RG_TSV2F_CTRL_1	0x09
+#define RG_TSV2F_CTRL_2	0x0A
+#define RG_TSV2F_CTRL_3	0x0B
+#define RG_TSV2F_CTRL_4	0x0C
+#define RG_TSV2F_CTRL_5	0x0D
+#define RG_TSV2F_CTRL_6	0x0E
+#define RG_TEMP_DATA_0	0x10
+#define RG_TEMP_DATA_1	0x11
+#define RG_TEMP_DATA_2	0x12
+#define RG_TEMP_DATA_3	0x13
+#define RG_RC_DATA_0	0x14
+#define RG_RC_DATA_1	0x15
+#define RG_RC_DATA_2	0x16
+#define RG_RC_DATA_3	0x17
+#define RG_DIV_DATA_0	0x18
+#define RG_DIV_DATA_1	0x19
+#define RG_DIV_DATA_2	0x1A
+#define RG_DIV_DATA_3	0x1B
+#define RG_TST_DATA_0	0x70
+#define RG_TST_DATA_1	0x71
+#define RG_TST_DATA_2	0x72
+#define RG_TST_CTRL	0x73
+#define RG_DBG_FQMTR	0xF0
+#define RG_DBG_LPSEQ	0xF1
+#define RG_DBG_STATE	0xF2
+#define RG_DBG_CHKSUM	0xF3
+#define RG_DID_LVTS	0xFC
+#define RG_DID_REV	0xFD
+#define RG_TSFM_RST	0xFF
+/*==================================================
+ * LVTS controller register
+ *==================================================
+ */
+#define LVTSMONCTL0_0	0x000
+#define LVTS_SINGLE_SENSE	BIT(9)
+#define ENABLE_SENSING_POINT(num)	(LVTS_SINGLE_SENSE | GENMASK(((num) - 1), 0))
+#define DISABLE_SENSING_POINT	(LVTS_SINGLE_SENSE | 0x0)
+#define LVTSMONCTL1_0	0x004
+#define LVTSMONCTL2_0	0x008
+#define LVTSMONINT_0	0x00C
+#define STAGE3_INT_EN	BIT(31)
+#define LVTSMONINTSTS_0	0x010
+#define LVTSMONIDET0_0	0x014
+#define LVTSMONIDET1_0	0x018
+#define LVTSMONIDET2_0	0x01C
+#define LVTSMONIDET3_0	0x020
+#define LVTSH2NTHRE_0	0x024
+#define LVTSHTHRE_0	0x028
+#define LVTSCTHRE_0	0x02C
+#define LVTSOFFSETH_0	0x030
+#define LVTSOFFSETL_0	0x034
+#define LVTSMSRCTL0_0	0x038
+#define LVTSMSRCTL1_0	0x03C
+#define LVTSTSSEL_0	0x040
+#define SET_SENSOR_INDEX	0x13121110
+#define LVTSDEVICETO_0	0x044
+#define LVTSCALSCALE_0	0x048
+#define SET_CALC_SCALE_RULES	0x00000300
+#define LVTS_ID_0	0x04C
+#define LVTS_CONFIG_0	0x050
+
+#define BROADCAST_ID_UPDATE	BIT(26)
+#define DEVICE_SENSING_STATUS	BIT(25)
+#define DEVICE_ACCESS_STARTUS	BIT(24)
+#define WRITE_ACCESS		BIT(16)
+#define DEVICE_WRITE		(BIT(31) | CK26M_ACTIVE | DEVICE_ACCESS_STARTUS \
+				| BIT(17) | WRITE_ACCESS)
+#define DEVICE_READ		(BIT(31) | CK26M_ACTIVE | DEVICE_ACCESS_STARTUS \
+				| 1 << 17)
+#define RESET_ALL_DEVICES	(DEVICE_WRITE | RG_TSFM_RST << 8 | 0xFF)
+#define READ_BACK_DEVICE_ID	(BIT(31) | CK26M_ACTIVE | BROADCAST_ID_UPDATE	\
+				| DEVICE_ACCESS_STARTUS | BIT(17)	\
+				| RG_DID_LVTS << 8)
+#define READ_DEVICE_REG(reg_idx)	(DEVICE_READ | (reg_idx) << 8 | 0x00)
+#define LVTSEDATA00_0	0x054
+#define LVTSEDATA01_0	0x058
+#define LVTSEDATA02_0	0x05C
+#define LVTSEDATA03_0	0x060
+#define LVTSMSR0_0	0x090
+#define MRS_RAW_MASK		GENMASK(15, 0)
+#define MRS_RAW_VALID_BIT	BIT(16)
+#define LVTSMSR1_0	0x094
+#define LVTSMSR2_0	0x098
+#define LVTSMSR3_0	0x09C
+#define LVTSIMMD0_0	0x0A0
+#define LVTSIMMD1_0	0x0A4
+#define LVTSIMMD2_0	0x0A8
+#define LVTSIMMD3_0	0x0AC
+#define LVTSRDATA0_0	0x0B0
+#define LVTSRDATA1_0	0x0B4
+#define LVTSRDATA2_0	0x0B8
+#define LVTSRDATA3_0	0x0BC
+#define LVTSPROTCTL_0	0x0C0
+#define PROTOFFSET	GENMASK(15, 0)
+#define LVTSPROTTA_0	0x0C4
+#define LVTSPROTTB_0	0x0C8
+#define LVTSPROTTC_0	0x0CC
+#define LVTSCLKEN_0	0x0E4
+#define ENABLE_LVTS_CTRL_CLK	(1)
+#define DISABLE_LVTS_CTRL_CLK	(0)
+#define LVTSDBGSEL_0	0x0E8
+#define LVTSDBGSIG_0	0x0EC
+#define LVTSSPARE0_0	0x0F0
+#define LVTSSPARE1_0	0x0F4
+#define LVTSSPARE2_0	0x0F8
+#define LVTSSPARE3_0	0x0FC
+
+#define THERMINTST	0xF04
+/*==================================================
+ * LVTS register mask
+ *==================================================
+ */
+#define THERMAL_COLD_INTERRUPT_0		0x00000001
+#define THERMAL_HOT_INTERRUPT_0			0x00000002
+#define THERMAL_LOW_OFFSET_INTERRUPT_0		0x00000004
+#define THERMAL_HIGH_OFFSET_INTERRUPT_0		0x00000008
+#define THERMAL_HOT2NORMAL_INTERRUPT_0		0x00000010
+#define THERMAL_COLD_INTERRUPT_1		0x00000020
+#define THERMAL_HOT_INTERRUPT_1			0x00000040
+#define THERMAL_LOW_OFFSET_INTERRUPT_1		0x00000080
+#define THERMAL_HIGH_OFFSET_INTERRUPT_1		0x00000100
+#define THERMAL_HOT2NORMAL_INTERRUPT_1		0x00000200
+#define THERMAL_COLD_INTERRUPT_2		0x00000400
+#define THERMAL_HOT_INTERRUPT_2			0x00000800
+#define THERMAL_LOW_OFFSET_INTERRUPT_2		0x00001000
+#define THERMAL_HIGH_OFFSET_INTERRUPT_2		0x00002000
+#define THERMAL_HOT2NORMAL_INTERRUPT_2		0x00004000
+#define THERMAL_AHB_TIMEOUT_INTERRUPT		0x00008000
+#define THERMAL_DEVICE_TIMEOUT_INTERRUPT	0x00008000
+#define THERMAL_IMMEDIATE_INTERRUPT_0		0x00010000
+#define THERMAL_IMMEDIATE_INTERRUPT_1		0x00020000
+#define THERMAL_IMMEDIATE_INTERRUPT_2		0x00040000
+#define THERMAL_FILTER_INTERRUPT_0		0x00080000
+#define THERMAL_FILTER_INTERRUPT_1		0x00100000
+#define THERMAL_FILTER_INTERRUPT_2		0x00200000
+#define THERMAL_COLD_INTERRUPT_3		0x00400000
+#define THERMAL_HOT_INTERRUPT_3			0x00800000
+#define THERMAL_LOW_OFFSET_INTERRUPT_3		0x01000000
+#define THERMAL_HIGH_OFFSET_INTERRUPT_3		0x02000000
+#define THERMAL_HOT2NORMAL_INTERRUPT_3		0x04000000
+#define THERMAL_IMMEDIATE_INTERRUPT_3		0x08000000
+#define THERMAL_FILTER_INTERRUPT_3		0x10000000
+#define THERMAL_PROTECTION_STAGE_1		0x20000000
+#define THERMAL_PROTECTION_STAGE_2		0x40000000
+#define THERMAL_PROTECTION_STAGE_3		0x80000000
+#endif /* __MTK_SOC_TEMP_LVTS_H__ */
-- 
2.18.0


More information about the linux-arm-kernel mailing list