[PATCH] Input: stmpe-keypad - add STMPE1801 support
Sergey Larin
cerg2010cerg2010 at mail.ru
Fri Jun 18 07:51:49 PDT 2021
This chip variant differs from others - it has different register
map and swapped rows/columns.
Signed-off-by: Sergey Larin <cerg2010cerg2010 at mail.ru>
---
drivers/input/keyboard/stmpe-keypad.c | 108 ++++++++++++++++++++------
1 file changed, 85 insertions(+), 23 deletions(-)
diff --git a/drivers/input/keyboard/stmpe-keypad.c b/drivers/input/keyboard/stmpe-keypad.c
index 7bf97285e30c..ed74578927a3 100644
--- a/drivers/input/keyboard/stmpe-keypad.c
+++ b/drivers/input/keyboard/stmpe-keypad.c
@@ -13,7 +13,7 @@
#include <linux/input/matrix_keypad.h>
#include <linux/mfd/stmpe.h>
-/* These are at the same addresses in all STMPE variants */
+/* These are at the same addresses in all STMPE variants, except 1801 */
#define STMPE_KPC_COL 0x60
#define STMPE_KPC_ROW_MSB 0x61
#define STMPE_KPC_ROW_LSB 0x62
@@ -42,14 +42,15 @@
#define STMPE_KEYPAD_MAX_DEBOUNCE 127
#define STMPE_KEYPAD_MAX_SCAN_COUNT 15
-#define STMPE_KEYPAD_MAX_ROWS 8
-#define STMPE_KEYPAD_MAX_COLS 8
+#define STMPE_KEYPAD_MAX_ROWS 10
+#define STMPE_KEYPAD_MAX_COLS 12
#define STMPE_KEYPAD_ROW_SHIFT 3
#define STMPE_KEYPAD_KEYMAP_MAX_SIZE \
(STMPE_KEYPAD_MAX_ROWS * STMPE_KEYPAD_MAX_COLS)
#define STMPE1601_NUM_DATA 5
+#define STMPE1801_NUM_DATA 5
#define STMPE2401_NUM_DATA 3
#define STMPE2403_NUM_DATA 5
@@ -67,6 +68,12 @@
* @max_rows: maximum number of rows supported
* @col_gpios: bitmask of gpios which can be used for columns
* @row_gpios: bitmask of gpios which can be used for rows
+ * @col_regs: registers for setting column pins
+ * @row_regs: registers for setting row pins
+ * @data_regs: registers for reading key data
+ * @ctrl_msb_reg: register for setting scan count
+ * @ctrl_lsb_reg: register for setting debounce time
+ * @cmd_reg: register for toggling scan mode
*/
struct stmpe_keypad_variant {
bool auto_increment;
@@ -77,6 +84,18 @@ struct stmpe_keypad_variant {
int max_rows;
unsigned int col_gpios;
unsigned int row_gpios;
+
+#define MAX_COL_REGS 3
+#define MAX_ROW_REGS 3
+#define MAX_DATA_REGS 5
+
+ u8 col_regs[MAX_COL_REGS];
+ u8 row_regs[MAX_ROW_REGS];
+ u8 data_regs[MAX_DATA_REGS];
+ u8 ctrl_msb_reg;
+ u8 ctrl_lsb_reg;
+ u8 cmd_reg;
+ bool read_inverted;
};
static const struct stmpe_keypad_variant stmpe_keypad_variants[] = {
@@ -88,6 +107,29 @@ static const struct stmpe_keypad_variant stmpe_keypad_variants[] = {
.max_rows = 8,
.col_gpios = 0x000ff, /* GPIO 0 - 7 */
.row_gpios = 0x0ff00, /* GPIO 8 - 15 */
+ .col_regs = { 0x60 },
+ .row_regs = { 0x62, 0x61 },
+ .data_regs = { 0x68, 0x69, 0x6a, 0x6b, 0x6c },
+ .ctrl_msb_reg = 0x63,
+ .ctrl_lsb_reg = 0x64,
+ .cmd_reg = 0x64,
+ .read_inverted = 0,
+ },
+ [STMPE1801] = {
+ .auto_increment = true,
+ .num_data = STMPE1801_NUM_DATA,
+ .num_normal_data = 3,
+ .max_cols = 10,
+ .max_rows = 8,
+ .col_gpios = 0x3ff00, /* GPIO 8 - 17 */
+ .row_gpios = 0x000ff, /* GPIO 0 - 7 */
+ .col_regs = { 0x31, 0x32 },
+ .row_regs = { 0x30 },
+ .data_regs = { 0x3a, 0x3b, 0x3c, 0x3d, 0x3e },
+ .ctrl_msb_reg = 0x33,
+ .ctrl_lsb_reg = 0x34,
+ .cmd_reg = 0x36,
+ .read_inverted = 1,
},
[STMPE2401] = {
.auto_increment = false,
@@ -98,6 +140,13 @@ static const struct stmpe_keypad_variant stmpe_keypad_variants[] = {
.max_rows = 12,
.col_gpios = 0x0000ff, /* GPIO 0 - 7*/
.row_gpios = 0x1f7f00, /* GPIO 8-14, 16-20 */
+ .col_regs = { 0x60 },
+ .row_regs = { 0x62, 0x61 },
+ .data_regs = { 0x68, 0x69, 0x6a, 0x6b, 0x6c },
+ .ctrl_msb_reg = 0x63,
+ .ctrl_lsb_reg = 0x64,
+ .cmd_reg = 0x64,
+ .read_inverted = 0,
},
[STMPE2403] = {
.auto_increment = true,
@@ -108,6 +157,13 @@ static const struct stmpe_keypad_variant stmpe_keypad_variants[] = {
.max_rows = 12,
.col_gpios = 0x0000ff, /* GPIO 0 - 7*/
.row_gpios = 0x1fef00, /* GPIO 8-14, 16-20 */
+ .col_regs = { 0x60 },
+ .row_regs = { 0x62, 0x61 },
+ .data_regs = { 0x68, 0x69, 0x6a, 0x6b, 0x6c },
+ .ctrl_msb_reg = 0x63,
+ .ctrl_lsb_reg = 0x64,
+ .cmd_reg = 0x64,
+ .read_inverted = 0,
},
};
@@ -145,11 +201,11 @@ static int stmpe_keypad_read_data(struct stmpe_keypad *keypad, u8 *data)
int i;
if (variant->auto_increment)
- return stmpe_block_read(stmpe, STMPE_KPC_DATA_BYTE0,
+ return stmpe_block_read(stmpe, variant->data_regs[0],
variant->num_data, data);
for (i = 0; i < variant->num_data; i++) {
- ret = stmpe_reg_read(stmpe, STMPE_KPC_DATA_BYTE0 + i);
+ ret = stmpe_reg_read(stmpe, variant->data_regs[i]);
if (ret < 0)
return ret;
@@ -176,7 +232,9 @@ static irqreturn_t stmpe_keypad_irq(int irq, void *dev)
u8 data = fifo[i];
int row = (data & STMPE_KPC_DATA_ROW) >> 3;
int col = data & STMPE_KPC_DATA_COL;
- int code = MATRIX_SCAN_CODE(row, col, STMPE_KEYPAD_ROW_SHIFT);
+ int code = variant->read_inverted ?
+ MATRIX_SCAN_CODE(col, row, STMPE_KEYPAD_ROW_SHIFT)
+ : MATRIX_SCAN_CODE(row, col, STMPE_KEYPAD_ROW_SHIFT);
bool up = data & STMPE_KPC_DATA_UP;
if ((data & STMPE_KPC_DATA_NOKEY_MASK)
@@ -265,7 +323,7 @@ static int stmpe_keypad_chip_init(struct stmpe_keypad *keypad)
{
const struct stmpe_keypad_variant *variant = keypad->variant;
struct stmpe *stmpe = keypad->stmpe;
- int ret;
+ int ret, val, i;
if (keypad->debounce_ms > STMPE_KEYPAD_MAX_DEBOUNCE)
return -EINVAL;
@@ -281,33 +339,37 @@ static int stmpe_keypad_chip_init(struct stmpe_keypad *keypad)
if (ret < 0)
return ret;
- ret = stmpe_reg_write(stmpe, STMPE_KPC_COL, keypad->cols);
- if (ret < 0)
- return ret;
-
- ret = stmpe_reg_write(stmpe, STMPE_KPC_ROW_LSB, keypad->rows);
- if (ret < 0)
- return ret;
+ val = keypad->cols;
+ i = 0;
+ do {
+ ret = stmpe_reg_write(stmpe, variant->col_regs[i++], val & 0xff);
+ if (ret < 0)
+ return ret;
+ } while ((val >>= 8) != 0);
- if (variant->max_rows > 8) {
- ret = stmpe_set_bits(stmpe, STMPE_KPC_ROW_MSB,
- STMPE_KPC_ROW_MSB_ROWS,
- keypad->rows >> 8);
+ val = keypad->rows;
+ i = 0;
+ do {
+ ret = stmpe_reg_write(stmpe, variant->row_regs[i++], val & 0xff);
if (ret < 0)
return ret;
- }
+ } while ((val >>= 8) != 0);
- ret = stmpe_set_bits(stmpe, STMPE_KPC_CTRL_MSB,
+ ret = stmpe_set_bits(stmpe, variant->ctrl_msb_reg,
STMPE_KPC_CTRL_MSB_SCAN_COUNT,
keypad->scan_count << 4);
if (ret < 0)
return ret;
- return stmpe_set_bits(stmpe, STMPE_KPC_CTRL_LSB,
- STMPE_KPC_CTRL_LSB_SCAN |
+ ret = stmpe_set_bits(stmpe, variant->ctrl_lsb_reg,
STMPE_KPC_CTRL_LSB_DEBOUNCE,
- STMPE_KPC_CTRL_LSB_SCAN |
(keypad->debounce_ms << 1));
+ if (ret < 0)
+ return ret;
+
+ return stmpe_set_bits(stmpe, variant->cmd_reg,
+ STMPE_KPC_CTRL_LSB_SCAN,
+ STMPE_KPC_CTRL_LSB_SCAN);
}
static void stmpe_keypad_fill_used_pins(struct stmpe_keypad *keypad,
--
2.32.0
More information about the linux-arm-kernel
mailing list