[PATCH v4 0/5] DTS updates for Marvell Armada CN913x platforms

[Gregory CLEMENT]

Hello,

> From: Konstantin Porotchkin <kostap at marvell.com>
>
> This patch series contains the following changes/fixes:
> 1. Add support for Armada CN913x Development Board topology "B"
> 2. Add support for Armada CN913x Reference Design boards (CRB)
> 3. Fixes the CP11X references in PHY binding document
> 4. Fixes the NAND paritioninig scheme in DTS eliminating gap between
> consecutive partitions
> All above changes are already intergated into Marvell official SDK sources
>
> v2:
> - extract common nodes from DB boards to separate DTSI files
> - disable eth2 on CRB boards until the required phy mode support is added
> - mention the switch part ID in CRB board description
>
> v3:
> - do not rename setup A DTS files for DB variants
> - fix a couple of wrong include names
>
> v4:
> - Rebase on top of Linus master branch (v5.11-rc7)
> - Remove HS400 timing from CRB AP SDHCI (not supported by connected eMMC)
> - Add cd-gpio entry to CP0 SDHCI for SD card support
> - Add a comment to CN9130-CRB patch about the required defconfig
>   changes for supporting the onboard i2c expander
> - Add Stefan's patch to enable 10G port on CN9130-DB platforms
>
> Grzegorz Jaszczyk (1):
>   Documentation/bindings: phy: update references to cp11x
>
> Konstantin Porotchkin (3):
>   arch/arm64/boot/dts/marvell: fix NAND partitioning scheme
>   arm64: dts: cn913x: add device trees for topology B boards
>   arm64: dts: add support for Marvell cn9130-crb platform
>
> Stefan Chulski (1):
>   dts: marvell: Enable 10G interface on 9130-DB board
>

I've applied patches 1 and 2, but I have issue with patch 3, there was some
changes around the phys and I am not sure of the correct way to modify
the patch.

Could you rebase it on v5.13-c1 and fix the merge issue ?

Thanks,

Gregory

>  .../bindings/phy/phy-mvebu-comphy.txt         |  12 +-
>  arch/arm64/boot/dts/marvell/Makefile          |   5 +
>  arch/arm64/boot/dts/marvell/cn9130-crb-A.dts  |  38 ++
>  arch/arm64/boot/dts/marvell/cn9130-crb-B.dts  |  46 ++
>  arch/arm64/boot/dts/marvell/cn9130-crb.dtsi   | 221 ++++++++++
>  arch/arm64/boot/dts/marvell/cn9130-db-B.dts   |  22 +
>  arch/arm64/boot/dts/marvell/cn9130-db.dts     | 393 +----------------
>  arch/arm64/boot/dts/marvell/cn9130-db.dtsi    | 402 ++++++++++++++++++
>  arch/arm64/boot/dts/marvell/cn9131-db-B.dts   |  22 +
>  arch/arm64/boot/dts/marvell/cn9131-db.dts     | 192 +--------
>  arch/arm64/boot/dts/marvell/cn9131-db.dtsi    | 201 +++++++++
>  arch/arm64/boot/dts/marvell/cn9132-db-B.dts   |  22 +
>  arch/arm64/boot/dts/marvell/cn9132-db.dts     | 211 +--------
>  arch/arm64/boot/dts/marvell/cn9132-db.dtsi    | 220 ++++++++++
>  14 files changed, 1223 insertions(+), 784 deletions(-)
>  create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-A.dts
>  create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb-B.dts
>  create mode 100644 arch/arm64/boot/dts/marvell/cn9130-crb.dtsi
>  create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db-B.dts
>  create mode 100644 arch/arm64/boot/dts/marvell/cn9130-db.dtsi
>  create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db-B.dts
>  create mode 100644 arch/arm64/boot/dts/marvell/cn9131-db.dtsi
>  create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db-B.dts
>  create mode 100644 arch/arm64/boot/dts/marvell/cn9132-db.dtsi
>
> -- 
> 2.17.1
>

-- 
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com