[PATCH v2 28/33] arm64: zynqmp: Sync psgtr node location with zcu104-revA

[Michal Simek]

zcu104-revA has node below pinctrl which is not the same on revC. Sync
location for easier comparison.
Also zc1751-dc1 is not using this position.

Signed-off-by: Michal Simek <michal.simek at xilinx.com>
---

Changes in v2: None

 .../boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts    | 14 +++++++-------
 arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts  | 14 +++++++-------
 2 files changed, 14 insertions(+), 14 deletions(-)

diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
index 9f176307b62a..d78439e891b9 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm015-dc1.dts
@@ -58,13 +58,6 @@ clock_si5338_3: clk150 {
 	};
 };
 
-&psgtr {
-	status = "okay";
-	/* dp, usb3, sata */
-	clocks = <&clock_si5338_0>, <&clock_si5338_2>, <&clock_si5338_3>;
-	clock-names = "ref1", "ref2", "ref3";
-};
-
 &fpd_dma_chan1 {
 	status = "okay";
 };
@@ -340,6 +333,13 @@ conf {
 	};
 };
 
+&psgtr {
+	status = "okay";
+	/* dp, usb3, sata */
+	clocks = <&clock_si5338_0>, <&clock_si5338_2>, <&clock_si5338_3>;
+	clock-names = "ref1", "ref2", "ref3";
+};
+
 &qspi {
 	status = "okay";
 	flash at 0 {
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
index fb8d76b5c27f..c21d9612ce04 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu104-revC.dts
@@ -429,6 +429,13 @@ conf-tx {
 	};
 };
 
+&psgtr {
+	status = "okay";
+	/* nc, sata, usb3, dp */
+	clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
+	clock-names = "ref1", "ref2", "ref3";
+};
+
 &qspi {
 	status = "okay";
 	flash at 0 {
@@ -446,13 +453,6 @@ &rtc {
 	status = "okay";
 };
 
-&psgtr {
-	status = "okay";
-	/* nc, sata, usb3, dp */
-	clocks = <&clock_8t49n287_5>, <&clock_8t49n287_2>, <&clock_8t49n287_3>;
-	clock-names = "ref1", "ref2", "ref3";
-};
-
 &sata {
 	status = "okay";
 	/* SATA OOB timing settings */
-- 
2.32.0