[PATCH v3 08/11] clk: renesas: Add CPG core wrapper for RZ/G2L SoC

[Lad, Prabhakar]

Hi Geert,

Thank you for the review.

On Thu, Jun 10, 2021 at 2:04 PM Geert Uytterhoeven <geert at linux-m68k.org> wrote:
>
> Hi Prabhakar,
>
> On Wed, Jun 9, 2021 at 5:33 PM Lad Prabhakar
> <prabhakar.mahadev-lad.rj at bp.renesas.com> wrote:
> > Add CPG core wrapper for RZ/G2L family.
> >
> > Based on a patch in the BSP by Binh Nguyen
> > <binh.nguyen.jz at renesas.com>.
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj at bp.renesas.com>
> > Reviewed-by: Biju Das <biju.das.jz at bp.renesas.com>
>
> Thanks for your patch!
>
> > --- a/drivers/clk/renesas/Kconfig
> > +++ b/drivers/clk/renesas/Kconfig
> > @@ -182,6 +182,11 @@ config CLK_RCAR_USB2_CLOCK_SEL
> >         help
> >           This is a driver for R-Car USB2 clock selector
> >
> > +config CLK_RZG2L
> > +       bool "Renesas RZ/G2L SoC clock support" if COMPILE_TEST && !ARCH_RENESAS
>
> s/SoC/family/?
>
Agreed.

> I think "if COMPILE_TEST", as all other entries are using, is sufficient.
>
> > +       depends on ARCH_RENESAS || COMPILE_TEST
>
> I think this can be dropped.
>
Agreed.

> > +       select RESET_CONTROLLER
> > +
> >  # Generic
>
> > --- /dev/null
> > +++ b/drivers/clk/renesas/renesas-rzg2l-cpg.c
>
> > +static struct clk
> > +*rzg2l_cpg_clk_src_twocell_get(struct of_phandle_args *clkspec,
> > +                              void *data)
> > +{
> > +       unsigned int clkidx = clkspec->args[1];
> > +       struct rzg2l_cpg_priv *priv = data;
> > +       struct device *dev = priv->dev;
> > +       const char *type;
> > +       struct clk *clk;
> > +
> > +       switch (clkspec->args[0]) {
> > +       case CPG_CORE:
> > +               type = "core";
> > +               if (clkidx > priv->last_dt_core_clk) {
> > +                       dev_err(dev, "Invalid %s clock index %u\n", type, clkidx);
> > +                       return ERR_PTR(-EINVAL);
> > +               }
> > +               clk = priv->clks[clkidx];
> > +               break;
> > +
> > +       case CPG_MOD:
> > +               type = "module";
> > +               if (clkidx > priv->num_core_clks + priv->num_mod_clks) {
>
> The range of module clocks in DT specifiers starts at zero, so
>
>     if (clkidx > priv->num_mod_clks) {
>
Thanks for the catch, yes the above check should be good.

>
> > +                       dev_err(dev, "Invalid %s clock index %u\n", type,
> > +                               clkidx);
> > +                       return ERR_PTR(-EINVAL);
> > +               }
> > +               clk = priv->clks[priv->num_core_clks + clkidx];
> > +               break;
> > +
> > +       default:
> > +               dev_err(dev, "Invalid CPG clock type %u\n", clkspec->args[0]);
> > +               return ERR_PTR(-EINVAL);
> > +       }
> > +
> > +       if (IS_ERR(clk))
> > +               dev_err(dev, "Cannot get %s clock %u: %ld", type, clkidx,
> > +                       PTR_ERR(clk));
> > +       else
> > +               dev_dbg(dev, "clock (%u, %u) is %pC at %lu Hz\n",
> > +                       clkspec->args[0], clkspec->args[1], clk,
> > +                       clk_get_rate(clk));
> > +       return clk;
> > +}
>
> With the above fixed:
> Reviewed-by: Geert Uytterhoeven <geert+renesas at glider.be>
>
> I can fix these while applying.
>
Thank you.

Cheers,
Prabhakar