[PATCH 1/7] arm64: dts: freescale: Add the top level dtsi support for imx8dxl
Abel Vesa
abel.vesa at nxp.com
Wed Jun 2 02:29:31 PDT 2021
On 21-05-18 15:35:41, Dong Aisheng wrote:
> On Tue, May 18, 2021 at 1:14 AM <abelvesa at kernel.org> wrote:
> >
> > From: Jacky Bai <ping.bai at nxp.com>
> >
> > The i.MX8DXL is a device targeting the automotive and industrial
> > market segments. The flexibility of the architecture allows for
> > use in a wide variety of general embedded applications. The chip
> > is designed to achieve both high performance and low power consumption.
> > The chip relies on the power efficient dual (2x) Cortex-A35 cluster.
> >
> > Add the reserved memory node property for dsp reserved memory,
> > the wakeup-irq property for SCU node, the imx ion, the rpmsg and the
> > cm4 rproc support.
> >
> > Signed-off-by: Jacky Bai <ping.bai at nxp.com>
> > Signed-off-by: Abel Vesa <abel.vesa at nxp.com>
>
> FIrst of all, did you run make dt_binding_check?
> I wonder there're dt binding missing for a few nodes
>
Fixing those in the next version.
> > ---
> > arch/arm64/boot/dts/freescale/imx8dxl.dtsi | 286 +++++++++++++++++++++
> > 1 file changed, 286 insertions(+)
> > create mode 100644 arch/arm64/boot/dts/freescale/imx8dxl.dtsi
> >
> > diff --git a/arch/arm64/boot/dts/freescale/imx8dxl.dtsi b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi
> > new file mode 100644
> > index 000000000000..43e0bcdc2469
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/freescale/imx8dxl.dtsi
> > @@ -0,0 +1,286 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +/*
> > + * Copyright 2019-2021 NXP
> > + */
> > +
> > +#include <dt-bindings/clock/imx8-clock.h>
> > +#include <dt-bindings/firmware/imx/rsrc.h>
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +#include <dt-bindings/input/input.h>
> > +#include <dt-bindings/pinctrl/pads-imx8dxl.h>
>
> this depends on pinctrl driver. Is that upstreamed already?
>
It is upstreamed.
> > +#include <dt-bindings/thermal/thermal.h>
> > +
> > +/ {
> > + interrupt-parent = <&gic>;
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > +
> > + aliases {
> > + ethernet0 = &fec1;
> > + ethernet1 = &eqos;
> > + gpio0 = &lsio_gpio0;
> > + gpio1 = &lsio_gpio1;
> > + gpio2 = &lsio_gpio2;
> > + gpio3 = &lsio_gpio3;
> > + gpio4 = &lsio_gpio4;
> > + gpio5 = &lsio_gpio5;
> > + gpio6 = &lsio_gpio6;
> > + gpio7 = &lsio_gpio7;
> > + i2c2 = &i2c2;
> > + i2c3 = &i2c3;
> > + mmc0 = &usdhc1;
> > + mmc1 = &usdhc2;
> > + mu1 = &lsio_mu1;
> > + serial0 = &lpuart0;
> > + serial1 = &lpuart1;
> > + serial2 = &lpuart2;
> > + serial3 = &lpuart3;
> > + };
> > +
> > + cpus: cpus {
> > + #address-cells = <2>;
> > + #size-cells = <0>;
> > +
> > + /* We have 1 clusters with 2 Cortex-A35 cores */
> > + A35_0: cpu at 0 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a35";
> > + reg = <0x0 0x0>;
> > + enable-method = "psci";
> > + next-level-cache = <&A35_L2>;
> > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
> > + #cooling-cells = <2>;
> > + operating-points-v2 = <&a35_opp_table>;
> > + };
> > +
> > + A35_1: cpu at 1 {
> > + device_type = "cpu";
> > + compatible = "arm,cortex-a35";
> > + reg = <0x0 0x1>;
> > + enable-method = "psci";
> > + next-level-cache = <&A35_L2>;
> > + clocks = <&clk IMX_SC_R_A35 IMX_SC_PM_CLK_CPU>;
> > + #cooling-cells = <2>;
> > + operating-points-v2 = <&a35_opp_table>;
> > + };
> > +
> > + A35_L2: l2-cache0 {
> > + compatible = "cache";
> > + };
> > + };
> > +
> > + a35_opp_table: opp-table {
> > + compatible = "operating-points-v2";
> > + opp-shared;
> > +
> > + opp-900000000 {
> > + opp-hz = /bits/ 64 <900000000>;
> > + opp-microvolt = <1000000>;
> > + clock-latency-ns = <150000>;
> > + };
> > +
> > + opp-1200000000 {
> > + opp-hz = /bits/ 64 <1200000000>;
> > + opp-microvolt = <1100000>;
> > + clock-latency-ns = <150000>;
> > + opp-suspend;
> > + };
> > + };
> > +
> > + reserved-memory {
> > + #address-cells = <2>;
> > + #size-cells = <2>;
> > + ranges;
> > +
> > + dsp_reserved: dsp at 92400000 {
> > + reg = <0 0x92400000 0 0x2000000>;
> > + no-map;
> > + };
> > + };
>
> this could be added when enabling DSP in case any changes required in upstream
>
Unfortunately, the imx8-ss-adma already depends on it. So it needs to go
in now, otherwise it won't build.
> > +
> > + rpmsg: rpmsg{
> > + compatible = "fsl,imx8qxp-rpmsg";
>
> I belive this is still not supported in upstream
> so drop it first
>
Removed in the next version.
> > + /* up to now, the following channels are used in imx rpmsg
> > + * - tx1/rx1: messages channel.
> > + * - general interrupt1: remote proc finish re-init rpmsg stack
> > + * when A core is partition reset.
> > + */
> > + mbox-names = "tx", "rx", "rxdb";
> > + mboxes = <&lsio_mu5 0 1
> > + &lsio_mu5 1 1
> > + &lsio_mu5 3 1>;
> > + mub-partition = <3>;
> > + status = "disabled";
> > + };
> > +
> > + imx8dxl_cm4: imx8dxl_cm4 at 0 {
> > + compatible = "fsl,imx8qxp-cm4";
>
> i'd suggest drop it first and add in separate patch
> as it's still not supported
>
Removed in the next version.
> > + rsc-da = <0x90000000>;
> > + mbox-names = "tx", "rx", "rxdb";
> > + mboxes = <&lsio_mu5 0 1
> > + &lsio_mu5 1 1
> > + &lsio_mu5 3 1>;
> > + mub-partition = <3>;
> > + core-index = <0>;
> > + core-id = <IMX_SC_R_M4_0_PID0>;
> > + status = "disabled";
> > + power-domains = <&pd IMX_SC_R_M4_0_PID0>,
> > + <&pd IMX_SC_R_M4_0_MU_1A>;
> > + };
> > +
> > + gic: interrupt-controller at 51a00000 {
> > + compatible = "arm,gic-v3";
> > + reg = <0x0 0x51a00000 0 0x10000>, /* GIC Dist */
> > + <0x0 0x51b00000 0 0xc0000>; /* GICR (RD_base + SGI_base) */
> > + #interrupt-cells = <3>;
> > + interrupt-controller;
> > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + pmu {
> > + compatible = "arm,armv8-pmuv3";
> > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH>;
> > + };
> > +
> > + psci {
> > + compatible = "arm,psci-1.0";
> > + method = "smc";
> > + };
> > +
> > + scu {
> > + compatible = "fsl,imx-scu";
> > + mbox-names = "tx0",
> > + "rx0",
> > + "gip3";
> > + mboxes = <&lsio_mu1 0 0
> > + &lsio_mu1 1 0
> > + &lsio_mu1 3 3>;
> > +
> > + pd: imx8dxl-pd {
> > + compatible = "fsl,imx8dxl-scu-pd", "fsl,scu-pd";
> > + #power-domain-cells = <1>;
> > + wakeup-irq = <160 163 235 236 237 228 229 230 231 238
> > + 239 240 166 169>;
>
> drop this property first which is still not supported
>
Removed in the next version.
> > + };
> > +
> > + clk: clock-controller {
> > + compatible = "fsl,imx8dxl-clk", "fsl,scu-clk";
> > + #clock-cells = <2>;
> > + clocks = <&xtal32k &xtal24m>;
> > + clock-names = "xtal_32KHz", "xtal_24Mhz";
> > + };
> > +
> > + iomuxc: pinctrl {
> > + compatible = "fsl,imx8dxl-iomuxc";
>
> make sure pinctrl upstreamed
>
It is upstreamed.
> > + };
> > +
> > + ocotp: imx8qx-ocotp {
> > + compatible = "fsl,imx8dxl-scu-ocotp", "fsl,imx8qxp-scu-ocotp";
>
> need update binding doc as well
>
Will do in the next version.
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + fec_mac0: mac at 2c4 {
> > + reg = <0x2c4 6>;
> > + };
> > +
> > + fec_mac1: mac at 2c6 {
> > + reg = <0x2c6 6>;
> > + };
> > + };
> > +
> > + rtc: rtc {
> > + compatible = "fsl,imx8dxl-sc-rtc", "fsl,imx8qxp-sc-rtc";
>
> pls update dt binding as well
>
I'll actually remove this in the next version.
Will be sent later on as a separate patch.
> > + };
> > +
> > + watchdog {
> > + compatible = "fsl,imx-sc-wdt";
> > + timeout-sec = <60>;
> > + };
> > +
> > + tsens: thermal-sensor {
> > + compatible = "fsl,imx-sc-thermal";
> > + #thermal-sensor-cells = <1>;
> > + };
> > + };
> > +
> > + timer {
> > + compatible = "arm,armv8-timer";
> > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_LOW>, /* Physical Secure */
> > + <GIC_PPI 14 IRQ_TYPE_LEVEL_LOW>, /* Physical Non-Secure */
> > + <GIC_PPI 11 IRQ_TYPE_LEVEL_LOW>, /* Virtual */
> > + <GIC_PPI 10 IRQ_TYPE_LEVEL_LOW>; /* Hypervisor */
> > + };
> > +
> > + thermal_zones: thermal-zones {
> > + cpu-thermal0 {
> > + polling-delay-passive = <250>;
> > + polling-delay = <2000>;
> > + thermal-sensors = <&tsens IMX_SC_R_SYSTEM>;
> > +
> > + trips {
> > + cpu_alert0: trip0 {
> > + temperature = <107000>;
> > + hysteresis = <2000>;
> > + type = "passive";
> > + };
> > + cpu_crit0: trip1 {
> > + temperature = <127000>;
> > + hysteresis = <2000>;
> > + type = "critical";
> > + };
> > + };
> > + cooling-maps {
> > + map0 {
> > + trip = <&cpu_alert0>;
> > + cooling-device =
> > + <&A35_0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
> > + <&A35_1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + clk_dummy: clock-dummy {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <0>;
> > + clock-output-names = "clk_dummy";
> > + };
> > +
> > + xtal32k: clock-xtal32k {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <32768>;
> > + clock-output-names = "xtal_32KHz";
> > + };
> > +
> > + xtal24m: clock-xtal24m {
> > + compatible = "fixed-clock";
> > + #clock-cells = <0>;
> > + clock-frequency = <24000000>;
> > + clock-output-names = "xtal_24MHz";
> > + };
> > +
> > + imx_ion {
> > + compatible = "fsl,mxc-ion";
>
> drop this unsupported node
>
Removed in the next version.
> Regards
> Aisheng
>
> > + fsl,heap-id = <0>;
> > + };
> > +
> > + sc_pwrkey: sc-powerkey {
> > + compatible = "fsl,imx8-pwrkey";
> > + linux,keycode = <KEY_POWER>;
> > + wakeup-source;
> > + };
> > +
> > + /* sorted in register address */
> > + #include "imx8-ss-adma.dtsi"
> > + #include "imx8-ss-conn.dtsi"
> > + #include "imx8-ss-ddr.dtsi"
> > + #include "imx8-ss-lsio.dtsi"
> > +};
> > +
> > +#include "imx8dxl-ss-adma.dtsi"
> > +#include "imx8dxl-ss-conn.dtsi"
> > +#include "imx8dxl-ss-lsio.dtsi"
> > +#include "imx8dxl-ss-ddr.dtsi"
> > --
> > 2.31.1
> >
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel at lists.infradead.org
> > https://eur01.safelinks.protection.outlook.com/?url=http%3A%2F%2Flists.infradead.org%2Fmailman%2Flistinfo%2Flinux-arm-kernel&data=04%7C01%7Cabel.vesa%40nxp.com%7C843de7d5f11f49ba992408d919cfafdc%7C686ea1d3bc2b4c6fa92cd99c5c301635%7C0%7C0%7C637569202065001061%7CUnknown%7CTWFpbGZsb3d8eyJWIjoiMC4wLjAwMDAiLCJQIjoiV2luMzIiLCJBTiI6Ik1haWwiLCJXVCI6Mn0%3D%7C1000&sdata=ZmB%2FXRdAz3Y0q2FFu2C2Y6cqYbfDQkk7Q1SNqESO2zc%3D&reserved=0
More information about the linux-arm-kernel
mailing list