[PATCH V2] remoteproc: imx_rproc: correct firmware reload

[Peng Fan (OSS)]

From: Peng Fan <peng.fan at nxp.com>

ENABLE_M4 should be set to 1 when loading code to TCM, otherwise
you will not able to replace the firmware after you stop m4.

Besides ENABLE_M4, we still need set SW_M4C_RST, because this bit
will be automatically set with SW_M4C_NON_SCLR_RST set.

Reviewed-by: Mathieu Poirier <mathieu.poirier at linaro.org>
Signed-off-by: Peng Fan <peng.fan at nxp.com>
---

V2:
 Add R-b tag from Mathieu
 Rebase on remoteproc/for-next
 This https://patchwork.kernel.org/project/linux-remoteproc/cover/1620274123-1461-1-git-send-email-peng.fan@oss.nxp.com/
 has been merged in remoteproc/for-next, so not mark here as dependency.


 drivers/remoteproc/imx_rproc.c | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/drivers/remoteproc/imx_rproc.c b/drivers/remoteproc/imx_rproc.c
index 7cc0cadea1cc..ce2ce42bee91 100644
--- a/drivers/remoteproc/imx_rproc.c
+++ b/drivers/remoteproc/imx_rproc.c
@@ -33,7 +33,8 @@
 
 #define IMX7D_M4_START			(IMX7D_ENABLE_M4 | IMX7D_SW_M4P_RST \
 					 | IMX7D_SW_M4C_RST)
-#define IMX7D_M4_STOP			IMX7D_SW_M4C_NON_SCLR_RST
+#define IMX7D_M4_STOP			(IMX7D_ENABLE_M4 | IMX7D_SW_M4C_RST | \
+					 IMX7D_SW_M4C_NON_SCLR_RST)
 
 /* Address: 0x020D8000 */
 #define IMX6SX_SRC_SCR			0x00
@@ -44,7 +45,8 @@
 
 #define IMX6SX_M4_START			(IMX6SX_ENABLE_M4 | IMX6SX_SW_M4P_RST \
 					 | IMX6SX_SW_M4C_RST)
-#define IMX6SX_M4_STOP			IMX6SX_SW_M4C_NON_SCLR_RST
+#define IMX6SX_M4_STOP			(IMX6SX_ENABLE_M4 | IMX6SX_SW_M4C_RST | \
+					 IMX6SX_SW_M4C_NON_SCLR_RST)
 #define IMX6SX_M4_RST_MASK		(IMX6SX_ENABLE_M4 | IMX6SX_SW_M4P_RST \
 					 | IMX6SX_SW_M4C_NON_SCLR_RST \
 					 | IMX6SX_SW_M4C_RST)
@@ -691,7 +693,7 @@ static int imx_rproc_detect_mode(struct imx_rproc *priv)
 		return ret;
 	}
 
-	if (!(val & dcfg->src_stop))
+	if ((val & dcfg->src_mask) != dcfg->src_stop)
 		priv->rproc->state = RPROC_DETACHED;
 
 	return 0;
-- 
2.30.0