[PATCH] remoteproc: imx_rproc: correct firmware reload

[Mathieu Poirier]

On Tue, Jun 01, 2021 at 06:29:39PM +0800, Peng Fan (OSS) wrote:
> From: Peng Fan <peng.fan at nxp.com>
> 
> ENABLE_M4 should be set to 1 when loading code to TCM, otherwise
> you will not able to replace the firmware after you stop m4.
> 
> Besides ENABLE_M4, we still need set SW_M4C_RST, because this bit
> will be automatically set with SW_M4C_NON_SCLR_RST set.
> 
> Signed-off-by: Peng Fan <peng.fan at nxp.com>
> ---
> 
> V1:
>  Although this is an fix, but it is not critical, patch is based on
>  https://patchwork.kernel.org/project/linux-remoteproc/cover/1620274123-1461-1-git-send-email-peng.fan@oss.nxp.com/
> 
>  drivers/remoteproc/imx_rproc.c | 8 +++++---
>  1 file changed, 5 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/remoteproc/imx_rproc.c b/drivers/remoteproc/imx_rproc.c
> index cd2ca96a30e5..ce2ce42bee91 100644
> --- a/drivers/remoteproc/imx_rproc.c
> +++ b/drivers/remoteproc/imx_rproc.c
> @@ -33,7 +33,8 @@
>  
>  #define IMX7D_M4_START			(IMX7D_ENABLE_M4 | IMX7D_SW_M4P_RST \
>  					 | IMX7D_SW_M4C_RST)
> -#define IMX7D_M4_STOP			(IMX7D_ENABLE_M4 | IMX7D_SW_M4C_NON_SCLR_RST)
> +#define IMX7D_M4_STOP			(IMX7D_ENABLE_M4 | IMX7D_SW_M4C_RST | \
> +					 IMX7D_SW_M4C_NON_SCLR_RST)
>  
>  /* Address: 0x020D8000 */
>  #define IMX6SX_SRC_SCR			0x00
> @@ -44,7 +45,8 @@
>  
>  #define IMX6SX_M4_START			(IMX6SX_ENABLE_M4 | IMX6SX_SW_M4P_RST \
>  					 | IMX6SX_SW_M4C_RST)
> -#define IMX6SX_M4_STOP			(IMX6SX_ENABLE_M4 | IMX6SX_SW_M4C_NON_SCLR_RST)
> +#define IMX6SX_M4_STOP			(IMX6SX_ENABLE_M4 | IMX6SX_SW_M4C_RST | \
> +					 IMX6SX_SW_M4C_NON_SCLR_RST)
>  #define IMX6SX_M4_RST_MASK		(IMX6SX_ENABLE_M4 | IMX6SX_SW_M4P_RST \
>  					 | IMX6SX_SW_M4C_NON_SCLR_RST \
>  					 | IMX6SX_SW_M4C_RST)
> @@ -691,7 +693,7 @@ static int imx_rproc_detect_mode(struct imx_rproc *priv)
>  		return ret;
>  	}
>  
> -	if (!(val & dcfg->src_stop))
> +	if ((val & dcfg->src_mask) != dcfg->src_stop)
>  		priv->rproc->state = RPROC_DETACHED;

Reviewed-by: Mathieu Poirier <mathieu.poirier at linaro.org>

Bjorn hasn't picked up this set yet so it is best to send a v7 of [1] with this
change merged in it.

Thanks,
Mathieu 

[1]. https://patchwork.kernel.org/project/linux-remoteproc/cover/1620274123-1461-1-git-send-email-peng.fan@oss.nxp.com/

>  
>  	return 0;
> -- 
> 2.30.0
>