[PATCH] ARM: dts: at91-sama5d27_wlsom1: add i2c recovery

[nicolas.ferre at microchip.com]

From: Nicolas Ferre <nicolas.ferre at microchip.com>

Add the i2c gpio pinctrls to support the i2c bus recovery on this board.

Signed-off-by: Nicolas Ferre <nicolas.ferre at microchip.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu at microchip.com>
---
 arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi | 22 +++++++++++++++++++--
 1 file changed, 20 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
index a06700e53e4c..025a78310e3a 100644
--- a/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
+++ b/arch/arm/boot/dts/at91-sama5d27_wlsom1.dtsi
@@ -43,14 +43,20 @@ uart6: serial at 200 {
 
 &i2c0 {
 	pinctrl-0 = <&pinctrl_i2c0_default>;
-	pinctrl-names = "default";
+	pinctrl-1 = <&pinctrl_i2c0_gpio>;
+	pinctrl-names = "default", "gpio";
+	sda-gpios = <&pioA PIN_PD21 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD22 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 };
 
 &i2c1 {
 	dmas = <0>, <0>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1_default>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	sda-gpios = <&pioA PIN_PD19 GPIO_ACTIVE_HIGH>;
+	scl-gpios = <&pioA PIN_PD20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
 	mcp16502 at 5b {
@@ -258,12 +264,24 @@ pinctrl_i2c0_default: i2c0_default {
 		bias-disable;
 	};
 
+	pinctrl_i2c0_gpio: i2c0_gpio {
+		pinmux = <PIN_PD21__GPIO>,
+			 <PIN_PD22__GPIO>;
+		bias-disable;
+	};
+
 	pinctrl_i2c1_default: i2c1_default {
 		pinmux = <PIN_PD19__TWD1>,
 			 <PIN_PD20__TWCK1>;
 		bias-disable;
 	};
 
+	pinctrl_i2c1_gpio: i2c1_gpio {
+		pinmux = <PIN_PD19__GPIO>,
+			 <PIN_PD20__GPIO>;
+		bias-disable;
+	};
+
 	pinctrl_macb0_default: macb0_default {
 		pinmux = <PIN_PB14__GTXCK>,
 			 <PIN_PB15__GTXEN>,
-- 
2.30.0