[PATCH V2] arm64: dts: broadcom: bcm4908: describe internal switch

Rafał Miłecki zajec5 at gmail.com
Wed Jan 13 06:09:46 EST 2021


From: Rafał Miłecki <rafal at milecki.pl>

BCM4908 has internal switch with 5 GPHYs. Ports 0 - 3 are always
connected to the internal PHYs. Remaining ports depend on device setup.

Asus GT-AC5300 has an extra switch with its PHYs accessible using the
internal MDIO.

CPU port and Ethernet interface remain to be documented.
---
V2: Use simple-bus
---
 .../bcm4908/bcm4908-asus-gt-ac5300.dts        | 51 +++++++++++
 .../boot/dts/broadcom/bcm4908/bcm4908.dtsi    | 85 ++++++++++++++++++-
 2 files changed, 135 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts
index 13c6b86eef21..51305e96fbd6 100644
--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts
+++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908-asus-gt-ac5300.dts
@@ -44,6 +44,57 @@ brightness {
 	};
 };
 
+&ports {
+	port at 0 {
+		label = "lan2";
+	};
+
+	port at 1 {
+		label = "lan1";
+	};
+
+	port at 2 {
+		label = "lan6";
+	};
+
+	port at 3 {
+		label = "lan5";
+	};
+
+	/* External BCM53134S switch */
+	port at 7 {
+		label = "sw";
+		reg = <7>;
+
+		fixed-link {
+			speed = <1000>;
+			full-duplex;
+		};
+	};
+};
+
+&mdio {
+	/* lan8 */
+	phy at 0 {
+		reg = <0>;
+	};
+
+	/* lan7 */
+	phy at 1 {
+		reg = <1>;
+	};
+
+	/* lan4 */
+	phy at 2 {
+		reg = <2>;
+	};
+
+	/* lan3 */
+	phy at 3 {
+		reg = <3>;
+	};
+};
+
 &nandcs {
 	nand-ecc-strength = <4>;
 	nand-ecc-step-size = <512>;
diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
index b5b772a9a51b..d30dd2042786 100644
--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
+++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
@@ -108,7 +108,7 @@ soc {
 		compatible = "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges = <0x00 0x00 0x80000000 0x10000>;
+		ranges = <0x00 0x00 0x80000000 0xd0000>;
 
 		usb at c300 {
 			compatible = "generic-ehci";
@@ -130,6 +130,89 @@ usb at d000 {
 			interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
 			status = "disabled";
 		};
+
+		switch at 80000 {
+			compatible = "simple-bus";
+			#size-cells = <1>;
+			#address-cells = <1>;
+			ranges = <0 0x80000 0x50000>;
+
+			switch at 0 {
+				compatible = "brcm,bcm4908-switch";
+				reg = <0x0 0x40000>,
+				      <0x40000 0x110>,
+				      <0x40340 0x30>,
+				      <0x40380 0x30>,
+				      <0x40600 0x34>,
+				      <0x40800 0x208>;
+				reg-names = "core", "reg", "intrl2_0",
+					    "intrl2_1", "fcb", "acb";
+				interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
+					     <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>;
+				brcm,num-gphy = <5>;
+				brcm,num-rgmii-ports = <2>;
+
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				ports: ports {
+					#address-cells = <1>;
+					#size-cells = <0>;
+
+					port at 0 {
+						reg = <0>;
+						phy-mode = "internal";
+						phy-handle = <&phy8>;
+					};
+
+					port at 1 {
+						reg = <1>;
+						phy-mode = "internal";
+						phy-handle = <&phy9>;
+					};
+
+					port at 2 {
+						reg = <2>;
+						phy-mode = "internal";
+						phy-handle = <&phy10>;
+					};
+
+					port at 3 {
+						reg = <3>;
+						phy-mode = "internal";
+						phy-handle = <&phy11>;
+					};
+				};
+			};
+
+			mdio: mdio at 405c0 {
+				compatible = "brcm,unimac-mdio";
+				reg = <0x405c0 0x8>;
+				reg-names = "mdio";
+				#size-cells = <1>;
+				#address-cells = <0>;
+
+				phy8: phy at 8 {
+					reg = <8>;
+				};
+
+				phy9: phy at 9 {
+					reg = <9>;
+				};
+
+				phy10: phy at a {
+					reg = <10>;
+				};
+
+				phy11: phy at b {
+					reg = <11>;
+				};
+
+				phy12: phy at c {
+					reg = <12>;
+				};
+			};
+		};
 	};
 
 	bus at ff800000 {
-- 
2.26.2




More information about the linux-arm-kernel mailing list