[PATCH v4 1/1] phy: fsl-imx8-mipi-dphy: Hook into runtime pm

[Liu Ying]

Hi Guido,

On Mon, 2021-02-22 at 19:38 +0100, Guido Günther wrote:
> This allows us to shut down the mipi power domain on the imx8. The
> alternative would be to drop the dphy from the mipi power domain in the
> SOCs device tree and only have the DSI host controller visible there but
> since the PD is mostly about the PHY that would defeat it's purpose.
> 
> This allows to shut off the power domain hen blanking the LCD panel:

s/hen/when/

> 
> pm_genpd_summary before:
> 
> domain                          status          slaves
>     /device                                             runtime status
> ----------------------------------------------------------------------
> mipi                            on
>     /devices/platform/soc at 0/soc at 0:bus at 30800000/30a00300.dphy  unsupported
>     /devices/platform/soc at 0/soc at 0:bus at 30800000/30a00000.mipi_dsi  suspended
> 
> after:
> 
> mipi                            off-0
>     /devices/platform/soc at 0/soc at 0:bus at 30800000/30a00300.dphy  suspended
>     /devices/platform/soc at 0/soc at 0:bus at 30800000/30a00000.mipi_dsi  suspended
> 
> Signed-off-by: Guido Günther <agx at sigxcpu.org>
> ---
>  drivers/phy/freescale/phy-fsl-imx8-mipi-dphy.c | 10 ++++++++++
>  1 file changed, 10 insertions(+)
> 
> diff --git a/drivers/phy/freescale/phy-fsl-imx8-mipi-dphy.c b/drivers/phy/freescale/phy-fsl-imx8-mipi-dphy.c
> index a95572b397ca..5de175695834 100644
> --- a/drivers/phy/freescale/phy-fsl-imx8-mipi-dphy.c
> +++ b/drivers/phy/freescale/phy-fsl-imx8-mipi-dphy.c
> @@ -14,6 +14,7 @@
>  #include <linux/of_platform.h>
>  #include <linux/phy/phy.h>
>  #include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
>  #include <linux/regmap.h>
>  
>  /* DPHY registers */
> @@ -469,6 +470,8 @@ static int mixel_dphy_probe(struct platform_device *pdev)
>  
>  	dev_set_drvdata(dev, priv);
>  
> +	pm_runtime_enable(dev);
> +

The runtime PM should be disabled if devm_phy_create()
or devm_of_phy_provider_register() fail.

Also, I'm just realizing that mixel_dphy_configure() accesses some PHY
registers, which likely needs the power domain on. However, the
phy-core doesn't manage the runtime PM for phy_configure(). It looks
that the NWL DSI bridge driver, which uses the PHY, enables the same
power domain prior to the PHY configuration. That's probably why
mixel_dphy_configure() gets power for accessing registers(if really
needed). So, perhaps, either make phy_configure() manage runtime PM or 
get/put runtime PM in mixel_dphy_configure().

Regards,
Liu Ying

>  	phy = devm_phy_create(dev, np, &mixel_dphy_phy_ops);
>  	if (IS_ERR(phy)) {
>  		dev_err(dev, "Failed to create phy %ld\n", PTR_ERR(phy));
> @@ -481,8 +484,15 @@ static int mixel_dphy_probe(struct platform_device *pdev)
>  	return PTR_ERR_OR_ZERO(phy_provider);
>  }
>  
> +static int mixel_dphy_remove(struct platform_device *pdev)
> +{
> +	pm_runtime_disable(&pdev->dev);
> +	return 0;
> +}
> +
>  static struct platform_driver mixel_dphy_driver = {
>  	.probe	= mixel_dphy_probe,
> +	.remove = mixel_dphy_remove,
>  	.driver = {
>  		.name = "mixel-mipi-dphy",
>  		.of_match_table	= mixel_dphy_of_match,