[PATCH 10/12] arm64: dts: rockchip: rk3568-evb: Enable VOP2 and hdmi

Sascha Hauer s.hauer at pengutronix.de
Thu Dec 2 07:34:49 PST 2021


On Wed, Nov 17, 2021 at 09:19:38AM -0600, Rob Herring wrote:
> On Wed, Nov 17, 2021 at 8:34 AM Sascha Hauer <s.hauer at pengutronix.de> wrote:
> >
> > This enabled the VOP2 display controller along with hdmi and the
> > required port routes which is enough to get a picture out of the
> > hdmi port of the board.
> >
> > Signed-off-by: Sascha Hauer <s.hauer at pengutronix.de>
> > ---
> >  .../boot/dts/rockchip/rk3568-evb1-v10.dts     | 24 +++++++++++++++++++
> >  1 file changed, 24 insertions(+)
> >
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
> > index 184e2aa2416af..156e001492173 100644
> > --- a/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
> > +++ b/arch/arm64/boot/dts/rockchip/rk3568-evb1-v10.dts
> > @@ -106,6 +106,12 @@ &gmac1m1_rgmii_clk
> >         status = "okay";
> >  };
> >
> > +&hdmi {
> > +       status = "okay";
> > +       avdd-0v9-supply = <&vdda0v9_image>;
> > +       avdd-1v8-supply = <&vcca1v8_image>;
> > +};
> > +
> >  &i2c0 {
> >         status = "okay";
> >
> > @@ -390,3 +396,21 @@ &sdmmc0 {
> >  &uart2 {
> >         status = "okay";
> >  };
> > +
> > +&vop {
> > +       status = "okay";
> > +       assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>;
> > +       assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>;
> > +};
> > +
> > +&vop_mmu {
> > +       status = "okay";
> > +};
> > +
> > +&hdmi_in_vp0 {
> > +       status = "okay";
> > +};
> > +
> > +&vp0_out_hdmi {
> > +       status = "okay";
> > +};
> 
> You can accomplish the same thing already with:
> 
> &vp0_out_hdmi {
>   remote-endpoint = <&hdmi_in_vp0>;
> };

My idea was to describe all possible connections in the dtsi file and
let the board dts writer only en/disable the needed connections. When
the connections are specified in the dts file then writing it is more
difficult and error prone.

> 
> or:
> 
> &vp0_out_hdmi {
>   /delete-property/ remote-endpoint;
> };

With this I have to change all connections that I don't need. With
status = "okay" I have to change all connections that I actually do
need, which will be much easier to read and write.

I'll stick to the status = "okay" method for the next round, maybe I can
still convince you ;)

If it's the 'status' property you don't like being used when it's not a
device that is enabled/disabled, then every other name would be fine
with me as well.

Sascha

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |



More information about the linux-arm-kernel mailing list