[PATCH v2 1/2] arm64: dts: mt8173: Set uart to mmio32 iotype

[Matthias Brugger]

Hi,

On 10/09/2020 10:43, Hsin-Yi Wang wrote:
> Set uart iotype to mmio32 to make earlycon work with stdout-path.
> 
> Signed-off-by: Hsin-Yi Wang <hsinyi at chromium.org>
> ---
>   arch/arm64/boot/dts/mediatek/mt8173.dtsi | 8 ++++++++
>   1 file changed, 8 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> index 5e046f9d48ce9..ca6ea71f5f435 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
> @@ -613,6 +613,8 @@ uart0: serial at 11002000 {
>   			interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_LOW>;
>   			clocks = <&pericfg CLK_PERI_UART0_SEL>, <&pericfg CLK_PERI_UART0>;
>   			clock-names = "baud", "bus";
> +			reg-io-width = <4>;

Why do we need that, we have
device->port.iotype = UPIO_MEM32;
in early_mtk8250_setup(). That should do the job already.


> +			reg-shift = <2>;

Can't we just add
device->port.regshift = 2;
to early_mtk8250_setup()? I think that would be a cleaner solution. As the 
serial device is the same for all SoCs, I don't expect any regression here.

CCing Eddie to correct me, if I'm wrong :)

Regards,
Matthias

>   			status = "disabled";
>   		};
>   
> @@ -623,6 +625,8 @@ uart1: serial at 11003000 {
>   			interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_LOW>;
>   			clocks = <&pericfg CLK_PERI_UART1_SEL>, <&pericfg CLK_PERI_UART1>;
>   			clock-names = "baud", "bus";
> +			reg-io-width = <4>;
> +			reg-shift = <2>;
>   			status = "disabled";
>   		};
>   
> @@ -633,6 +637,8 @@ uart2: serial at 11004000 {
>   			interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_LOW>;
>   			clocks = <&pericfg CLK_PERI_UART2_SEL>, <&pericfg CLK_PERI_UART2>;
>   			clock-names = "baud", "bus";
> +			reg-io-width = <4>;
> +			reg-shift = <2>;
>   			status = "disabled";
>   		};
>   
> @@ -643,6 +649,8 @@ uart3: serial at 11005000 {
>   			interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_LOW>;
>   			clocks = <&pericfg CLK_PERI_UART3_SEL>, <&pericfg CLK_PERI_UART3>;
>   			clock-names = "baud", "bus";
> +			reg-io-width = <4>;
> +			reg-shift = <2>;
>   			status = "disabled";
>   		};
>   
>