[PATCH 1/2] arm64: dts: ti: k3-j7200-som-p0: main_i2c0 have an ioexpander on the SOM

[Peter Ujfalusi]

It is used to control several SOM level muxes to make sure that the correct
signals are routed to the correct pin on the SOM <-> CPB connectors.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi at ti.com>
---
 .../dts/ti/k3-j7200-common-proc-board.dts     | 11 --------
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi   | 26 +++++++++++++++++++
 2 files changed, 26 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index 6b3863108571..2721137d8943 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -43,13 +43,6 @@ J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
 };
 
 &main_pmx0 {
-	main_i2c0_pins_default: main-i2c0-pins-default {
-		pinctrl-single,pins = <
-			J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
-			J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
-		>;
-	};
-
 	main_i2c1_pins_default: main-i2c1-pins-default {
 		pinctrl-single,pins = <
 			J721E_IOPAD(0xdc, PIN_INPUT_PULLUP, 3) /* (U3) ECAP0_IN_APWM_OUT.I2C1_SCL */
@@ -146,10 +139,6 @@ &cpsw_port1 {
 };
 
 &main_i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&main_i2c0_pins_default>;
-	clock-frequency = <400000>;
-
 	exp1: gpio at 20 {
 		compatible = "ti,tca6416";
 		reg = <0x20>;
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index fbd17d38f6b6..7b5e9aa0324e 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -48,6 +48,15 @@ J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
 	};
 };
 
+&main_pmx0 {
+	main_i2c0_pins_default: main-i2c0-pins-default {
+		pinctrl-single,pins = <
+			J721E_IOPAD(0xd4, PIN_INPUT_PULLUP, 0) /* (V3) I2C0_SCL */
+			J721E_IOPAD(0xd8, PIN_INPUT_PULLUP, 0) /* (W2) I2C0_SDA */
+		>;
+	};
+};
+
 &hbmc {
 	/* OSPI and HBMC are muxed inside FSS, Bootloader will enable
 	 * appropriate node based on board detection
@@ -131,3 +140,20 @@ &mailbox0_cluster10 {
 &mailbox0_cluster11 {
 	status = "disabled";
 };
+
+&main_i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_i2c0_pins_default>;
+	clock-frequency = <400000>;
+
+	exp_som: gpio at 21 {
+		compatible = "ti,tca6408";
+		reg = <0x21>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		gpio-line-names = "USB2.0_MUX_SEL", "CANUART_MUX1_SEL0",
+				  "CANUART_MUX2_SEL0", "CANUART_MUX_SEL1",
+				  "UART/LIN_MUX_SEL", "TRC_D17/AUDIO_REFCLK_SEL",
+				  "GPIO_LIN_EN", "CAN_STB";
+	};
+};
-- 
Peter

Texas Instruments Finland Oy, Porkkalankatu 22, 00180 Helsinki.
Y-tunnus/Business ID: 0615521-4. Kotipaikka/Domicile: Helsinki