[PATCH] arm64: dts: ls1043a: update USB nodes status to match board config

[Ran Wang]

ls1043a-rdb and ls1043a-qds board’s default HW config (such as
pin mux selection) would not enable some USB controllers’
data path, which causing over-current detected on those
controllers. This will hit the case of ‘xhci driver prevent bus suspend
if a root hub port detected over-current condition’, causing system
failed to be suspended. So disable them in device tree to resolve this
issue.

Signed-off-by: Ran Wang <ran.wang_1 at nxp.com>
---
 arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts | 4 ++++
 arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts | 8 ++++++++
 arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi    | 3 +++
 3 files changed, 15 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
index 1aac81d..fea167d 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-qds.dts
@@ -148,4 +148,8 @@
 	};
 };
 
+&usb0 {
+	status = "okay";
+};
+
 #include "fsl-ls1043-post.dtsi"
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
index bfa9d95..3516af4 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a-rdb.dts
@@ -209,3 +209,11 @@
 		fsl,tdm-interface;
 	};
 };
+
+&usb0 {
+	status = "okay";
+};
+
+&usb1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
index 3b641bd..c6d8dcb 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls1043a.dtsi
@@ -677,6 +677,7 @@
 			snps,quirk-frame-length-adjustment = <0x20>;
 			snps,dis_rxdet_inp3_quirk;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+			status = "disabled";
 		};
 
 		usb1: usb3 at 3000000 {
@@ -687,6 +688,7 @@
 			snps,quirk-frame-length-adjustment = <0x20>;
 			snps,dis_rxdet_inp3_quirk;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+			status = "disabled";
 		};
 
 		usb2: usb3 at 3100000 {
@@ -697,6 +699,7 @@
 			snps,quirk-frame-length-adjustment = <0x20>;
 			snps,dis_rxdet_inp3_quirk;
 			snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
+			status = "disabled";
 		};
 
 		sata: sata at 3200000 {
-- 
2.7.4