[PATCH 8/8] arm64: dts: allwinner: Add OrangePi Zero 2 .dts

[Icenowy Zheng]

在 2020-12-02星期三的 13:54 +0000，Andre Przywara写道：
> The OrangePi Zero 2 is a development board with the new H616 SoC.
> 
> It features the usual connectors used on those small boards, and
> comes
> with the AXP305, which seems to be compatible with the AXP805.
> 
> For more details see: http://linux-sunxi.org/Xunlong_Orange_Pi_Zero2
> 
> Signed-off-by: Andre Przywara <andre.przywara at arm.com>
> ---
>  arch/arm64/boot/dts/allwinner/Makefile        |   1 +
>  .../allwinner/sun50i-h616-orangepi-zero2.dts  | 228
> ++++++++++++++++++
>  2 files changed, 229 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616-
> orangepi-zero2.dts
> 
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile
> b/arch/arm64/boot/dts/allwinner/Makefile
> index 211d1e9d4701..0cf8299b1ce7 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -35,3 +35,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-orangepi-one-
> plus.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-pine-h64-model-b.dtb
>  dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h6-tanix-tx6.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h616-orangepi-zero2.dtb
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-
> zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-
> zero2.dts
> new file mode 100644
> index 000000000000..814f5b4fec7c
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> @@ -0,0 +1,228 @@
> +// SPDX-License-Identifier: (GPL-2.0+ or MIT)
> +/*
> + * Copyright (C) 2020 Arm Ltd.
> + */
> +
> +/dts-v1/;
> +
> +#include "sun50i-h616.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +/ {
> +	model = "OrangePi Zero2";
> +	compatible = "xunlong,orangepi-zero2", "allwinner,sun50i-h616";
> +
> +	aliases {
> +		ethernet0 = &emac0;
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +
> +		power {
> +			label = "orangepi:red:power";
> +			gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13
> */
> +			default-state = "on";
> +		};
> +
> +		status {
> +			label = "orangepi:green:status";
> +			gpios = <&pio 2 12 GPIO_ACTIVE_HIGH>; /* PC12
> */
> +		};
> +	};
> +
> +	reg_vcc5v: vcc5v {
> +		/* board wide 5V supply directly from the USB-C socket
> */
> +		compatible = "regulator-fixed";
> +		regulator-name = "vcc-5v";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +	};
> +
> +	reg_usb1_vbus: usb1-vbus {
> +		compatible = "regulator-fixed";
> +		regulator-name = "usb1-vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		enable-active-high;
> +		gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; /* PC16 */
> +		status = "okay";
> +	};
> +};
> +
> +&ehci0 {
> +	status = "okay";
> +};
> +
> +&ehci1 {
> +	status = "okay";
> +};
> +
> +/* USB 2 & 3 are on headers only. */
> +
> +&emac0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&ext_rgmii_pins>;
> +	phy-mode = "rgmii";
> +	phy-handle = <&ext_rgmii_phy>;
> +	phy-supply = <&reg_dcdce>;
> +	allwinner,rx-delay-ps = <3100>;
> +	allwinner,tx-delay-ps = <700>;
> +	status = "okay";
> +};
> +
> +&mdio {
> +	ext_rgmii_phy: ethernet-phy at 1 {
> +		compatible = "ethernet-phy-ieee802.3-c22";
> +		reg = <1>;
> +	};
> +};
> +
> +&mmc0 {
> +	vmmc-supply = <&reg_dcdce>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;	/* PF6 */
> +	bus-width = <4>;
> +	status = "okay";
> +};
> +
> +&ohci0 {
> +	status = "okay";
> +};
> +
> +&ohci1 {
> +	status = "okay";
> +};
> +
> +&r_i2c {
> +	status = "okay";
> +
> +	axp305: pmic at 36 {
> +		compatible = "x-powers,axp305", "x-powers,axp805",
> +			     "x-powers,axp806";
> +		reg = <0x36>;
> +
> +		/* dummy interrupt to appease the driver for now */
> +		interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>;
> +		interrupt-controller;
> +		#interrupt-cells = <1>;

Is dummy interrupt future-proof?

> +
> +		x-powers,self-working-mode;
> +		vina-supply = <&reg_vcc5v>;
> +		vinb-supply = <&reg_vcc5v>;
> +		vinc-supply = <&reg_vcc5v>;
> +		vind-supply = <&reg_vcc5v>;
> +		vine-supply = <&reg_vcc5v>;
> +		aldoin-supply = <&reg_vcc5v>;
> +		bldoin-supply = <&reg_vcc5v>;
> +		cldoin-supply = <&reg_vcc5v>;
> +
> +		regulators {
> +			reg_aldo1: aldo1 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc-sys";
> +			};
> +
> +			reg_aldo2: aldo2 {
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc3v3-ext";
> +			};
> +
> +			reg_aldo3: aldo3 {
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc3v3-ext2";
> +			};
> +
> +			reg_bldo1: bldo1 {
> +				regulator-always-on;
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +				regulator-name = "vcc1v8";
> +			};
> +
> +			bldo2 {
> +				/* unused */
> +			};
> +
> +			bldo3 {
> +				/* unused */
> +			};
> +
> +			bldo4 {
> +				/* unused */
> +			};
> +
> +			cldo1 {
> +				/* reserved */
> +			};
> +
> +			cldo2 {
> +				/* unused */
> +			};
> +
> +			cldo3 {
> +				/* unused */
> +			};
> +
> +			reg_dcdca: dcdca {
> +				regulator-always-on;
> +				regulator-min-microvolt = <810000>;
> +				regulator-max-microvolt = <1080000>;
> +				regulator-name = "vdd-cpu";
> +			};
> +
> +			reg_dcdcc: dcdcc {
> +				regulator-always-on;
> +				regulator-min-microvolt = <810000>;
> +				regulator-max-microvolt = <1080000>;
> +				regulator-name = "vdd-gpu-sys";
> +			};
> +
> +			reg_dcdcd: dcdcd {
> +				regulator-always-on;
> +				regulator-min-microvolt = <1500000>;
> +				regulator-max-microvolt = <1500000>;
> +				regulator-name = "vdd-dram";
> +			};
> +
> +			reg_dcdce: dcdce {
> +				regulator-boot-on;
> +				regulator-min-microvolt = <3300000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-name = "vcc-eth-mmc";
> +			};
> +
> +			sw {
> +				/* unused */
> +			};
> +		};
> +	};
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_ph_pins>;
> +	status = "okay";
> +};
> +
> +&usbotg {
> +	dr_mode = "otg";

The board is locked to a UFP due to fixed resistor on CC. OTG is not
possible.

> +	status = "okay";
> +};
> +
> +&usbphy {
> +	usb0_vbus-supply = <&reg_vcc5v>;
> +	usb1_vbus-supply = <&reg_usb1_vbus>;
> +	status = "okay";
> +};