[PATCH 3/3] dmaengine: sun6i: Add support for Allwinner A64

Maxime Ripard maxime.ripard at free-electrons.com
Mon Sep 4 00:04:15 PDT 2017


On Fri, Sep 01, 2017 at 11:35:40PM +0100, André Przywara wrote:
> On 01/09/17 07:04, Maxime Ripard wrote:
> > On Fri, Sep 01, 2017 at 01:31:35AM +0100, Andre Przywara wrote:
> >> Hi,
> >>
> >> On 31/08/17 00:36, Stefan Brüns wrote:
> >>> The A64 SoC has the same dma engine as the H3 (sun8i), with a
> >>> reduced amount of physical channels. Add the proper config data
> >>> and compatible string to support it.
> >>
> >> ...
> >>
> >>> diff --git a/drivers/dma/sun6i-dma.c b/drivers/dma/sun6i-dma.c
> >>> index 5f4eee4513e5..6a17c5d63582 100644
> >>> --- a/drivers/dma/sun6i-dma.c
> >>> +++ b/drivers/dma/sun6i-dma.c
> >>> @@ -1068,6 +1068,12 @@ static struct sun6i_dma_config sun8i_h3_dma_cfg = {
> >>>  	.nr_max_vchans   = 34,
> >>>  	.dmac_variant    = DMAC_VARIANT_H3,
> >>>  };
> >>> +
> >>> +static struct sun6i_dma_config sun50i_a64_dma_cfg = {
> >>> +	.nr_max_channels = 8,
> >>> +	.nr_max_requests = 27,
> >>> +	.nr_max_vchans   = 38,
> >>> +	.dmac_variant    = DMAC_VARIANT_H3,
> >>>  };
> >>>  
> >>>  static const struct of_device_id sun6i_dma_match[] = {
> >>> @@ -1075,6 +1081,7 @@ static const struct of_device_id sun6i_dma_match[] = {
> >>>  	{ .compatible = "allwinner,sun8i-a23-dma", .data = &sun8i_a23_dma_cfg },
> >>>  	{ .compatible = "allwinner,sun8i-a83t-dma", .data = &sun8i_a83t_dma_cfg },
> >>>  	{ .compatible = "allwinner,sun8i-h3-dma", .data = &sun8i_h3_dma_cfg },
> >>> +	{ .compatible = "allwinner,sun50i-a64-dma", .data = &sun50i_a64_dma_cfg },
> >>>  	{ /* sentinel */ }
> >>>  };
> >>>  MODULE_DEVICE_TABLE(of, sun6i_dma_match);
> >>
> >> I was wondering if should use the opportunity to expose those values as
> >> DT properties instead of hard-wiring them to a compatible string in the
> >> driver every time we add support for a new SoC?
> >> We could introduce a new compatible string (say: "allwinner,sunxi-dma"),
> >> then describe properties for the number of channels and requests and
> >> vchans and parse those from the DT at probe time.
> >> With this we might be able to support future SoCs without Linux *driver*
> >> changes, by just providing the right DT. This would have worked already
> >> for instance for the A83T support, which just changed those values.
> >>
> >> For instance with this quick patch below (just compile tested, and without
> >> your refactoring).
> >> The DT node would then read something like:
> >> 	dma: dma-controller at 01c02000 {
> >> 		compatible = "allwinner,sun50i-a64-dma",
> >> 			     "allwinner,sunxi-dma";
> >> 		reg = <0x01c02000 0x1000>;
> >> 		interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> >> 		clocks = <&ccu CLK_BUS_DMA>;
> >> 		resets = <&ccu RST_BUS_DMA>;
> >> 		#dma-cells = <1>;
> >> 		allwinner,max_channels = <8>;
> >> 		allwinner,max_requests = <27>;
> >> 		allwinner,max_vchans = <38>;
> >> 	};
> > 
> > We're still going to need a different compatible anyway, so it's not
> > really like it would change anything.
> 
> Well, not for now, but possibly in the future. And we should start with
> this at one point. If we would have had this type of binding already for
> H3, we could have added the A64 support without driver changes just by a
> DT change.

That's not true. As usual with these kinds of generic binding
arguments (it's definitely not personal, you're far from the only one
making them), it completely ignores the fact that the IP itself might
change from one revision to another, and its behaviour might too.

The A64 for example moved at least one register off, and has a
different set of burst size / width.

It's something you can't account for when you initially define the
binding, unless you describe all the registers, plus all their
parameters and the way you interact with them, which isn't going to
happen if you want to keep your sanity.

And obviously, while maintaining the stability of the binding of those
hundreds properties.

Or, you can base all this on the compatible, and be done with it once
and for all.

Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170904/f376efb8/attachment.sig>


More information about the linux-arm-kernel mailing list