[PATCH v8 02/10] dt-bindings: net: dwmac-sun8i: update documentation about integrated PHY

Rob Herring robh at kernel.org
Mon Oct 23 15:06:48 PDT 2017


On Mon, Oct 23, 2017 at 08:56:18PM +0200, Corentin Labbe wrote:
> This patch add documentation about the MDIO switch used on sun8i-h3-emac
> for integrated PHY.
> 
> Signed-off-by: Corentin Labbe <clabbe.montjoie at gmail.com>
> ---
>  .../devicetree/bindings/net/dwmac-sun8i.txt        | 139 +++++++++++++++++++--
>  1 file changed, 127 insertions(+), 12 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
> index 725f3b187886..3e37db10fa02 100644
> --- a/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
> +++ b/Documentation/devicetree/bindings/net/dwmac-sun8i.txt
> @@ -4,18 +4,18 @@ This device is a platform glue layer for stmmac.
>  Please see stmmac.txt for the other unchanged properties.
>  
>  Required properties:
> -- compatible: should be one of the following string:
> +- compatible: must be one of the following string:
>  		"allwinner,sun8i-a83t-emac"
>  		"allwinner,sun8i-h3-emac"
>  		"allwinner,sun8i-v3s-emac"
>  		"allwinner,sun50i-a64-emac"
>  - reg: address and length of the register for the device.
>  - interrupts: interrupt for the device
> -- interrupt-names: should be "macirq"
> +- interrupt-names: must be "macirq"
>  - clocks: A phandle to the reference clock for this device
> -- clock-names: should be "stmmaceth"
> +- clock-names: must be "stmmaceth"
>  - resets: A phandle to the reset control for this device
> -- reset-names: should be "stmmaceth"
> +- reset-names: must be "stmmaceth"
>  - phy-mode: See ethernet.txt
>  - phy-handle: See ethernet.txt
>  - #address-cells: shall be 1
> @@ -39,23 +39,38 @@ Optional properties for the following compatibles:
>  - allwinner,leds-active-low: EPHY LEDs are active low
>  
>  Required child node of emac:
> -- mdio bus node: should be named mdio
> +- mdio bus node: with compatible "snps,dwmac-mdio"
>  
>  Required properties of the mdio node:
>  - #address-cells: shall be 1
>  - #size-cells: shall be 0
>  
> -The device node referenced by "phy" or "phy-handle" should be a child node
> +The device node referenced by "phy" or "phy-handle" must be a child node
>  of the mdio node. See phy.txt for the generic PHY bindings.
>  
> -Required properties of the phy node with the following compatibles:
> +The following compatibles require that the emac node have a mdio-mux child
> +node called "mdio-mux":
> +  - "allwinner,sun8i-h3-emac"
> +  - "allwinner,sun8i-v3s-emac":
> +Required properties for the mdio-mux node:
> +  - compatible = "mdio-mux", "allwinner,sun8i-h3-mdio-mux"

I think you can drop mdio-mux. They are in the wrong order anyway.

> +  - one child mdio for the integrated mdio with the compatible
> +    "allwinner,sun8i-h3-mdio-internal"
> +  - one child mdio for the external mdio if present (V3s have none)
> +Required properties for the mdio-mux children node:
> +  - reg: 1 for internal MDIO bus, 2 for external MDIO bus
> +
> +The following compatibles require a PHY node representing the integrated
> +PHY, under the integrated MDIO bus node if an mdio-mux node is used:
>    - "allwinner,sun8i-h3-emac",
>    - "allwinner,sun8i-v3s-emac":

Please refer to mdio-mux.txt somewhere in here.

> +
> +Required properties of the integrated phy node:
>  - clocks: a phandle to the reference clock for the EPHY
>  - resets: a phandle to the reset control for the EPHY
> +- Must be a child of the integrated mdio
>  
> -Example:
> -
> +Example with integrated PHY:
>  emac: ethernet at 1c0b000 {
>  	compatible = "allwinner,sun8i-h3-emac";
>  	syscon = <&syscon>;
> @@ -72,13 +87,113 @@ emac: ethernet at 1c0b000 {
>  	phy-handle = <&int_mii_phy>;
>  	phy-mode = "mii";
>  	allwinner,leds-active-low;
> +
> +	mdio0: mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "snps,dwmac-mdio";
> +	};
> +
> +	mdio-mux {
> +		compatible = "mdio-mux", "allwinner,sun8i-h3-mdio-mux";

To be compliant with the mdio-mux binding, you need a mdio-parent-bus 
property. Though that property is optional, so maybe the mdio-mux 
binding just needs to say when it is optional. Presumably when the 
parent is the mdio bus controller. 

> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		int_mdio: mdio at 1 {
> +			compatible = "allwinner,sun8i-h3-mdio-internal";
> +			reg = <1>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			int_mii_phy: ethernet-phy at 1 {
> +				reg = <1>;
> +				clocks = <&ccu CLK_BUS_EPHY>;
> +				resets = <&ccu RST_BUS_EPHY>;
> +				phy-is-integrated;
> +			};
> +		};
> +		ext_mdio: mdio at 2 {
> +			reg = <2>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +	};
> +};
> +
> +Example with external PHY:
> +emac: ethernet at 1c0b000 {
> +	compatible = "allwinner,sun8i-h3-emac";
> +	syscon = <&syscon>;
> +	reg = <0x01c0b000 0x104>;
> +	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
> +	interrupt-names = "macirq";
> +	resets = <&ccu RST_BUS_EMAC>;
> +	reset-names = "stmmaceth";
> +	clocks = <&ccu CLK_BUS_EMAC>;
> +	clock-names = "stmmaceth";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	phy-handle = <&ext_rgmii_phy>;
> +	phy-mode = "rgmii";
> +	allwinner,leds-active-low;
> +
> +	mdio0: mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		compatible = "snps,dwmac-mdio";
> +	};
> +
> +	mdio-mux {
> +		compatible = "mdio-mux", "allwinner,sun8i-h3-mdio-mux";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		int_mdio: mdio at 1 {
> +			compatible = "allwinner,sun8i-h3-mdio-internal";
> +			reg = <1>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			int_mii_phy: ethernet-phy at 1 {
> +				reg = <1>;
> +				clocks = <&ccu CLK_BUS_EPHY>;
> +				resets = <&ccu RST_BUS_EPHY>;
> +			};
> +		};
> +		ext_mdio: mdio at 2 {
> +			reg = <2>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			ext_rgmii_phy: ethernet-phy at 1 {
> +				reg = <1>;
> +			};
> +		}:
> +	};
> +};
> +
> +Example with SoC without integrated PHY
> +
> +emac: ethernet at 1c0b000 {
> +	compatible = "allwinner,sun8i-a83t-emac";
> +	syscon = <&syscon>;
> +	reg = <0x01c0b000 0x104>;
> +	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
> +	interrupt-names = "macirq";
> +	resets = <&ccu RST_BUS_EMAC>;
> +	reset-names = "stmmaceth";
> +	clocks = <&ccu CLK_BUS_EMAC>;
> +	clock-names = "stmmaceth";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	phy-handle = <&ext_rgmii_phy>;
> +	phy-mode = "rgmii";
> +
>  	mdio: mdio {
> +		compatible = "snps,dwmac-mdio";
>  		#address-cells = <1>;
>  		#size-cells = <0>;
> -		int_mii_phy: ethernet-phy at 1 {
> +		ext_rgmii_phy: ethernet-phy at 1 {
>  			reg = <1>;
> -			clocks = <&ccu CLK_BUS_EPHY>;
> -			resets = <&ccu RST_BUS_EPHY>;
>  		};
>  	};
>  };
> -- 
> 2.13.6
> 



More information about the linux-arm-kernel mailing list