[PATCH v1] dmaengine: stm32_mdma: activate pack/unpack feature

Pierre-Yves MORDRET pierre-yves.mordret at st.com
Tue Oct 17 06:43:47 PDT 2017


If source and destination bus width differs pack/unpack MDMA
feature has to be activated for alignment.
This pack/unpack feature implies to have both source/destination address
and buffer length aligned on bus width.

Fixes: a4ffb13c8946 ("dmaengine: Add STM32 MDMA driver")
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret at st.com>
---
 drivers/dma/stm32-mdma.c | 84 ++++++++++++++++++++++++++++--------------------
 1 file changed, 50 insertions(+), 34 deletions(-)

diff --git a/drivers/dma/stm32-mdma.c b/drivers/dma/stm32-mdma.c
index d3be6bf..daa1602 100644
--- a/drivers/dma/stm32-mdma.c
+++ b/drivers/dma/stm32-mdma.c
@@ -387,14 +387,20 @@ static int stm32_mdma_get_width(struct stm32_mdma_chan *chan,
 	}
 }
 
-static enum dma_slave_buswidth stm32_mdma_get_max_width(u32 buf_len, u32 tlen)
+static enum dma_slave_buswidth stm32_mdma_get_max_width(dma_addr_t addr,
+							u32 buf_len, u32 tlen)
 {
 	enum dma_slave_buswidth max_width = DMA_SLAVE_BUSWIDTH_8_BYTES;
 
 	for (max_width = DMA_SLAVE_BUSWIDTH_8_BYTES;
 	     max_width > DMA_SLAVE_BUSWIDTH_1_BYTE;
 	     max_width >>= 1) {
-		if (((buf_len % max_width) == 0) && (tlen >= max_width))
+		/*
+		 * Address and buffer length both have to be aligned on
+		 * bus width
+		 */
+		if ((((buf_len | addr) & (max_width - 1)) == 0) &&
+		    tlen >= max_width)
 			break;
 	}
 
@@ -486,7 +492,8 @@ static void stm32_mdma_set_bus(struct stm32_mdma_device *dmadev, u32 *ctbr,
 static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan,
 				     enum dma_transfer_direction direction,
 				     u32 *mdma_ccr, u32 *mdma_ctcr,
-				     u32 *mdma_ctbr, u32 buf_len)
+				     u32 *mdma_ctbr, dma_addr_t addr,
+				     u32 buf_len)
 {
 	struct stm32_mdma_device *dmadev = stm32_mdma_get_dev(chan);
 	struct stm32_mdma_chan_config *chan_config = &chan->chan_config;
@@ -520,6 +527,9 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan,
 	ctcr &= ~STM32_MDMA_CTCR_LEN2_MSK;
 	ctcr |= STM32_MDMA_CTCR_TLEN((tlen - 1));
 
+	/* Disable Pack Enable */
+	ctcr &= ~STM32_MDMA_CTCR_PKE;
+
 	/* Check burst size constraints */
 	if (src_maxburst * src_addr_width > STM32_MDMA_MAX_BURST ||
 	    dst_maxburst * dst_addr_width > STM32_MDMA_MAX_BURST) {
@@ -551,6 +561,8 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan,
 
 	switch (direction) {
 	case DMA_MEM_TO_DEV:
+		dst_addr = chan->dma_config.dst_addr;
+
 		/* Set device data size */
 		dst_bus_width = stm32_mdma_get_width(chan, dst_addr_width);
 		if (dst_bus_width < 0)
@@ -567,7 +579,7 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan,
 		ctcr |= STM32_MDMA_CTCR_DBURST((ilog2(dst_best_burst)));
 
 		/* Set memory data size */
-		src_addr_width = stm32_mdma_get_max_width(buf_len, tlen);
+		src_addr_width = stm32_mdma_get_max_width(addr, buf_len, tlen);
 		chan->mem_width = src_addr_width;
 		src_bus_width = stm32_mdma_get_width(chan, src_addr_width);
 		if (src_bus_width < 0)
@@ -587,15 +599,19 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan,
 		ctcr |= STM32_MDMA_CTCR_SBURST((ilog2(src_best_burst)));
 
 		/* Select bus */
-		dst_addr = chan->dma_config.dst_addr;
 		stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS,
 				   dst_addr);
 
+		if (dst_bus_width != src_bus_width)
+			ctcr |= STM32_MDMA_CTCR_PKE;
+
 		/* Set destination address */
 		stm32_mdma_write(dmadev, STM32_MDMA_CDAR(chan->id), dst_addr);
 		break;
 
 	case DMA_DEV_TO_MEM:
+		src_addr = chan->dma_config.src_addr;
+
 		/* Set device data size */
 		src_bus_width = stm32_mdma_get_width(chan, src_addr_width);
 		if (src_bus_width < 0)
@@ -611,7 +627,7 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan,
 		ctcr |= STM32_MDMA_CTCR_SBURST((ilog2(src_best_burst)));
 
 		/* Set memory data size */
-		dst_addr_width = stm32_mdma_get_max_width(buf_len, tlen);
+		dst_addr_width = stm32_mdma_get_max_width(addr, buf_len, tlen);
 		chan->mem_width = dst_addr_width;
 		dst_bus_width = stm32_mdma_get_width(chan, dst_addr_width);
 		if (dst_bus_width < 0)
@@ -630,10 +646,12 @@ static int stm32_mdma_set_xfer_param(struct stm32_mdma_chan *chan,
 		ctcr |= STM32_MDMA_CTCR_DBURST((ilog2(dst_best_burst)));
 
 		/* Select bus */
-		src_addr = chan->dma_config.src_addr;
 		stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS,
 				   src_addr);
 
+		if (dst_bus_width != src_bus_width)
+			ctcr |= STM32_MDMA_CTCR_PKE;
+
 		/* Set source address */
 		stm32_mdma_write(dmadev, STM32_MDMA_CSAR(chan->id), src_addr);
 		break;
@@ -719,23 +737,27 @@ static int stm32_mdma_setup_xfer(struct stm32_mdma_chan *chan,
 			return -EINVAL;
 		}
 
-		ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr,
-						&ctbr, sg_dma_len(sg));
-		if (ret < 0)
-			return ret;
-
 		if (direction == DMA_MEM_TO_DEV) {
 			src_addr = sg_dma_address(sg);
 			dst_addr = dma_config->dst_addr;
+			ret = stm32_mdma_set_xfer_param(chan, direction, &ccr,
+							&ctcr, &ctbr, src_addr,
+							sg_dma_len(sg));
 			stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS,
 					   src_addr);
 		} else {
 			src_addr = dma_config->src_addr;
 			dst_addr = sg_dma_address(sg);
+			ret = stm32_mdma_set_xfer_param(chan, direction, &ccr,
+							&ctcr, &ctbr, dst_addr,
+							sg_dma_len(sg));
 			stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS,
 					   dst_addr);
 		}
 
+		if (ret < 0)
+			return ret;
+
 		stm32_mdma_setup_hwdesc(chan, desc, direction, i, src_addr,
 					dst_addr, sg_dma_len(sg), ctcr, ctbr,
 					i == sg_len - 1, i == 0, false);
@@ -830,27 +852,29 @@ stm32_mdma_prep_dma_cyclic(struct dma_chan *c, dma_addr_t buf_addr,
 	if (!desc)
 		return NULL;
 
-	ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr, &ctbr,
-					period_len);
-	if (ret < 0)
-		goto xfer_setup_err;
-
-	/* Enable interrupts */
-	ccr &= ~STM32_MDMA_CCR_IRQ_MASK;
-	ccr |= STM32_MDMA_CCR_TEIE | STM32_MDMA_CCR_CTCIE | STM32_MDMA_CCR_BTIE;
-	desc->ccr = ccr;
-
 	/* Select bus */
 	if (direction == DMA_MEM_TO_DEV) {
 		src_addr = buf_addr;
+		ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr,
+						&ctbr, src_addr, period_len);
 		stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_SBUS,
 				   src_addr);
 	} else {
 		dst_addr = buf_addr;
+		ret = stm32_mdma_set_xfer_param(chan, direction, &ccr, &ctcr,
+						&ctbr, dst_addr, period_len);
 		stm32_mdma_set_bus(dmadev, &ctbr, STM32_MDMA_CTBR_DBUS,
 				   dst_addr);
 	}
 
+	if (ret < 0)
+		goto xfer_setup_err;
+
+	/* Enable interrupts */
+	ccr &= ~STM32_MDMA_CCR_IRQ_MASK;
+	ccr |= STM32_MDMA_CCR_TEIE | STM32_MDMA_CCR_CTCIE | STM32_MDMA_CCR_BTIE;
+	desc->ccr = ccr;
+
 	/* Configure hwdesc list */
 	for (i = 0; i < count; i++) {
 		if (direction == DMA_MEM_TO_DEV) {
@@ -956,9 +980,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src,
 		ctcr |= STM32_MDMA_CTCR_TLEN((tlen - 1));
 
 		/* Set source best burst size */
-		max_width = stm32_mdma_get_max_width(len, tlen);
-		if (src % max_width)
-			max_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+		max_width = stm32_mdma_get_max_width(src, len, tlen);
 		src_bus_width = stm32_mdma_get_width(chan, max_width);
 
 		max_burst = tlen / max_width;
@@ -971,9 +993,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src,
 			STM32_MDMA_CTCR_SINCOS(src_bus_width);
 
 		/* Set destination best burst size */
-		max_width = stm32_mdma_get_max_width(len, tlen);
-		if (dest % max_width)
-			max_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+		max_width = stm32_mdma_get_max_width(dest, len, tlen);
 		dst_bus_width = stm32_mdma_get_width(chan, max_width);
 
 		max_burst = tlen / max_width;
@@ -1014,9 +1034,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src,
 					   STM32_MDMA_MAX_BLOCK_LEN);
 
 			/* Set source best burst size */
-			max_width = stm32_mdma_get_max_width(len, tlen);
-			if (src % max_width)
-				max_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+			max_width = stm32_mdma_get_max_width(src, len, tlen);
 			src_bus_width = stm32_mdma_get_width(chan, max_width);
 
 			max_burst = tlen / max_width;
@@ -1030,9 +1048,7 @@ stm32_mdma_prep_dma_memcpy(struct dma_chan *c, dma_addr_t dest, dma_addr_t src,
 				STM32_MDMA_CTCR_SINCOS(src_bus_width);
 
 			/* Set destination best burst size */
-			max_width = stm32_mdma_get_max_width(len, tlen);
-			if (dest % max_width)
-				max_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+			max_width = stm32_mdma_get_max_width(dest, len, tlen);
 			dst_bus_width = stm32_mdma_get_width(chan, max_width);
 
 			max_burst = tlen / max_width;
-- 
2.7.4




More information about the linux-arm-kernel mailing list