[PATCH v4 01/12] mmc: dt-bindings: Add reg/source_cg/latch-ck for Mediatek MMC bindings

Ulf Hansson ulf.hansson at linaro.org
Tue Oct 10 03:45:08 PDT 2017


On 10 October 2017 at 11:30, Chaotian Jing <chaotian.jing at mediatek.com> wrote:
> Change the comptiable for support of multi-platform
> Make compatible explicit
> Add description for reg
> Add description for source_cg
> Add description for mediatek,latch-ck
> Note that source_cg and mediatek,latch-ck are optional for some projects,
> eg, MT2701 do not have source_cg, and MT2712 do not need
> mediatek,latch-ck
>
> Signed-off-by: Chaotian Jing <chaotian.jing at mediatek.com>
> ---
>  Documentation/devicetree/bindings/mmc/mtk-sd.txt | 16 +++++++++++++---
>  1 file changed, 13 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/mmc/mtk-sd.txt b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> index 4182ea3..2bb585b 100644
> --- a/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> +++ b/Documentation/devicetree/bindings/mmc/mtk-sd.txt
> @@ -7,10 +7,18 @@ This file documents differences between the core properties in mmc.txt
>  and the properties used by the msdc driver.
>
>  Required properties:
> -- compatible: Should be "mediatek,mt8173-mmc","mediatek,mt8135-mmc"
> +- compatible: value should be either of the following.
> +       "mediatek,mt8135-mmc": for mmc host ip compatible with mt8135
> +       "mediatek,mt8173-mmc": for mmc host ip compatible with mt8173
> +       "mediatek,mt2701-mmc": for mmc host ip compatible with mt2701
> +       "mediatek,mt2712-mmc": for mmc host ip compatible with mt2712
> +- reg: physical base address of the controller and length
>  - interrupts: Should contain MSDC interrupt number
> -- clocks: MSDC source clock, HCLK
> -- clock-names: "source", "hclk"
> +- clocks: Should contain phandle for the clock feeding the MMC controller
> +- clock-names: Should contain the following:
> +       "source" - source clock (required)
> +       "hclk" - HCLK which used for host (required)
> +       "source_cg" - independent source clock gate (required for MT2712)
>  - pinctrl-names: should be "default", "state_uhs"
>  - pinctrl-0: should contain default/high speed pin ctrl
>  - pinctrl-1: should contain uhs mode pin ctrl
> @@ -30,6 +38,8 @@ Optional properties:
>  - mediatek,hs400-cmd-resp-sel-rising:  HS400 command response sample selection
>                                        If present,HS400 command responses are sampled on rising edges.
>                                        If not present,HS400 command responses are sampled on falling edges.
> +- mediatek,latch-ck: Some SoCs do not support enhance_rx, need set correct latch-ck to avoid data crc
> +                    error caused by stop clock(fifo full)
>
>  Examples:
>  mmc0: mmc at 11230000 {
> --
> 1.8.1.1.dirty
>

Looks good to me, however awaiting an ack from a DT maintainer before
I can apply.

Kind regards
Uffe



More information about the linux-arm-kernel mailing list