[PATCH v2] dts: display5: Device tree description of LWN's DISPLAY5 board

Łukasz Majewski lukma at denx.de
Fri Oct 6 13:50:56 PDT 2017


Dear All,

> This commit adds device tree description of Liebherr's Display5 board.

Gentle ping on this patch.....

Best regards,
Łukasz

> 
> Signed-off-by: Lukasz Majewski <lukma at denx.de>
> 
> ---
> Changes for v2:
> 
> - Postpone adding Mitsubishi display
> - Replace GPL with dual GPL/X11 licenses
> - Remove superfluous "i2s-master" property
> - Replace pinctrl 0x80000000 value (meaning that this ping shall not be
>    configured in Linux) with proper values (set by bootloader)
> ---
>   arch/arm/boot/dts/Makefile                         |   1 +
>   .../dts/imx6q-display5-tianma-tm070-1280x768.dts   |  51 ++
>   arch/arm/boot/dts/imx6q-display5.dtsi              | 582 +++++++++++++++++++++
>   3 files changed, 634 insertions(+)
>   create mode 100644 arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
>   create mode 100644 arch/arm/boot/dts/imx6q-display5.dtsi
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 4b17f35..c1648f0 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -400,6 +400,7 @@ dtb-$(CONFIG_SOC_IMX6Q) += \
>   	imx6q-cm-fx6.dtb \
>   	imx6q-cubox-i.dtb \
>   	imx6q-dfi-fs700-m60.dtb \
> +	imx6q-display5-tianma-tm070-1280x768.dtb \
>   	imx6q-dmo-edmqmx6.dtb \
>   	imx6q-evi.dtb \
>   	imx6q-gk802.dtb \
> diff --git a/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts b/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
> new file mode 100644
> index 0000000..16658b7
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-display5-tianma-tm070-1280x768.dts
> @@ -0,0 +1,51 @@
> +/*
> + * Copyright 2017
> + * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is licensed under the terms of the GNU General Public
> + *     License version 2.  This program is licensed "as is" without
> + *     any warranty of any kind, whether express or implied.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q-display5.dtsi"
> +
> +&panel {
> +	compatible = "tianma,tm070jdhg30";
> +};
> +
> +&ldb {
> +	lvds0: lvds-channel at 0 {
> +		fsl,data-mapping = "spwg";
> +		fsl,data-width = <18>;
> +	};
> +};
> diff --git a/arch/arm/boot/dts/imx6q-display5.dtsi b/arch/arm/boot/dts/imx6q-display5.dtsi
> new file mode 100644
> index 0000000..a7d9144
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6q-display5.dtsi
> @@ -0,0 +1,582 @@
> +/*
> + * Copyright 2017
> + * Lukasz Majewski, DENX Software Engineering, lukma at denx.de
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is licensed under the terms of the GNU General Public
> + *     License version 2.  This program is licensed "as is" without
> + *     any warranty of any kind, whether express or implied.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +
> +#include "imx6q.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/pwm/pwm.h>
> +#include <dt-bindings/sound/fsl-imx-audmux.h>
> +
> +/ {
> +	model = "Liebherr (LWN) display5 i.MX6 Quad Board";
> +	compatible = "lwn,display5", "fsl,imx6q";
> +
> +	memory {
> +		reg = <0x10000000 0x40000000>;
> +	};
> +
> +	backlight_lvds: backlight {
> +		compatible = "pwm-backlight";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_backlight>;
> +		pwms = <&pwm2 0 5000000 0>;
> +		brightness-levels = <  0   1   2   3   4   5   6   7   8   9
> +				      10  11  12  13  14  15  16  17  18  19
> +				      20  21  22  23  24  25  26  27  28  29
> +				      30  31  32  33  34  35  36  37  38  39
> +				      40  41  42  43  44  45  46  47  48  49
> +				      50  51  52  53  54  55  56  57  58  59
> +				      60  61  62  63  64  65  66  67  68  69
> +				      70  71  72  73  74  75  76  77  78  79
> +				      80  81  82  83  84  85  86  87  88  89
> +				      90  91  92  93  94  95  96  97  98  99
> +				     100 101 102 103 104 105 106 107 108 109
> +				     110 111 112 113 114 115 116 117 118 119
> +				     120 121 122 123 124 125 126 127 128 129
> +				     130 131 132 133 134 135 136 137 138 139
> +				     140 141 142 143 144 145 146 147 148 149
> +				     150 151 152 153 154 155 156 157 158 159
> +				     160 161 162 163 164 165 166 167 168 169
> +				     170 171 172 173 174 175 176 177 178 179
> +				     180 181 182 183 184 185 186 187 188 189
> +				     190 191 192 193 194 195 196 197 198 199
> +				     200 201 202 203 204 205 206 207 208 209
> +				     210 211 212 213 214 215 216 217 218 219
> +				     220 221 222 223 224 225 226 227 228 229
> +				     230 231 232 233 234 235 236 237 238 239
> +				     240 241 242 243 244 245 246 247 248 249
> +				     250 251 252 253 254 255>;
> +		default-brightness-level = <250>;
> +		enable-gpios = <&gpio5 7 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	reg_lvds: regulator-lvds {
> +		compatible = "regulator-fixed";
> +		regulator-name = "lvds_ppen";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_reg_lvds>;
> +		gpio = <&gpio5 13 GPIO_ACTIVE_HIGH>;
> +		enable-active-high;
> +	};
> +
> +	reg_usbh1_vbus: usb-h1-vbus {
> +		compatible = "regulator-fixed";
> +		gpio = <&gpio3 31 GPIO_ACTIVE_LOW>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_usbh1_vbus>;
> +		regulator-name = "usb_h1_vbus";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +	};
> +
> +	sound {
> +		compatible = "simple-audio-card";
> +		label = "tfa9879-mono";
> +
> +		simple-audio-card,dai-link {
> +			/* DAC */
> +			format = "i2s";
> +			bitclock-master = <&dailink_master>;
> +			frame-master = <&dailink_master>;
> +
> +			dailink_master: cpu {
> +			    sound-dai = <&ssi2>;
> +			};
> +			codec {
> +			    sound-dai = <&codec>;
> +			};
> +		};
> +	};
> +
> +	panel: panel-lvds0 {
> +		backlight = <&backlight_lvds>;
> +		power-supply = <&reg_lvds>;
> +
> +		port {
> +			panel_in_lvds0: endpoint {
> +				remote-endpoint = <&lvds0_out>;
> +			};
> +		};
> +	};
> +};
> +
> +&audmux {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_audmux>;
> +	status = "okay";
> +
> +	ssi2 {
> +		fsl,audmux-port = <1>;
> +		fsl,port-config = <
> +			(IMX_AUDMUX_V2_PTCR_SYN |
> +			 IMX_AUDMUX_V2_PTCR_TFSEL(5) |
> +			 IMX_AUDMUX_V2_PTCR_TCSEL(5) |
> +			 IMX_AUDMUX_V2_PTCR_TFSDIR |
> +			 IMX_AUDMUX_V2_PTCR_TCLKDIR)
> +			IMX_AUDMUX_V2_PDCR_RXDSEL(5)
> +		>;
> +	};
> +
> +	aud6 {
> +		fsl,audmux-port = <5>;
> +		fsl,port-config = <
> +			(IMX_AUDMUX_V2_PTCR_RFSEL(8) |
> +			 IMX_AUDMUX_V2_PTCR_RCSEL(8) |
> +			 IMX_AUDMUX_V2_PTCR_TFSEL(1) |
> +			 IMX_AUDMUX_V2_PTCR_TCSEL(1) |
> +			 IMX_AUDMUX_V2_PTCR_RFSDIR |
> +			 IMX_AUDMUX_V2_PTCR_RCLKDIR |
> +			 IMX_AUDMUX_V2_PTCR_TFSDIR |
> +			 IMX_AUDMUX_V2_PTCR_TCLKDIR)
> +			IMX_AUDMUX_V2_PDCR_RXDSEL(1)
> +		>;
> +	};
> +};
> +
> +&ecspi2 {
> +	cs-gpios = <&gpio5 29 GPIO_ACTIVE_LOW>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_ecspi2_cs &pinctrl_ecspi2_flwp>;
> +	status = "okay";
> +
> +	s25fl256s: flash at 0 {
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		compatible = "jedec,spi-nor";
> +		spi-max-frequency = <40000000>;
> +		reg = <0>;
> +
> +		partition at 0 {
> +			label = "SPL (spi)";
> +			reg = <0x0 0x20000>;
> +			read-only;
> +		};
> +		partition at 1 {
> +			label = "u-boot (spi)";
> +			reg = <0x20000 0x100000>;
> +			read-only;
> +		};
> +		partition at 2 {
> +			label = "uboot-env (spi)";
> +			reg = <0x120000 0x10000>;
> +		};
> +		partition at 3 {
> +			label = "uboot-envr (spi)";
> +			reg = <0x130000 0x10000>;
> +		};
> +		partition at 4 {
> +			label = "linux-recovery (spi)";
> +			reg = <0x140000 0x800000>;
> +		};
> +		partition at 5 {
> +			label = "swupdate-fitImg (spi)";
> +			reg = <0x940000 0x400000>;
> +		};
> +		partition at 6 {
> +			label = "swupdate-initramfs (spi)";
> +			reg = <0xD40000 0x800000>;
> +		};
> +	};
> +};
> +
> +&ecspi3 {
> +	cs-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi3 &pinctrl_ecspi3_cs &pinctrl_ecspi3_flwp>;
> +	status = "okay";
> +};
> +
> +&fec {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enet>;
> +	phy-mode = "rgmii";
> +	status = "okay";
> +
> +	fixed-link {
> +		speed = <100>;
> +		full-duplex;
> +	};
> +};
> +
> +&i2c1 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c1>;
> +	status = "okay";
> +
> +	codec: tfa9879 at 6C {
> +		#sound-dai-cells = <0>;
> +		compatible = "tfa9879";
> +		reg = <0x6C>;
> +	};
> +};
> +
> +&i2c2 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c2>;
> +	status = "okay";
> +};
> +
> +&i2c3 {
> +	clock-frequency = <400000>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c3>;
> +	status = "okay";
> +
> +	at24 at 50 {
> +		compatible = "at24,24c256";
> +		pagesize = <64>;
> +		reg = <0x50>;
> +	};
> +
> +	pfuze100: pmic at 08 {
> +		compatible = "fsl,pfuze100";
> +		reg = <0x08>;
> +
> +		regulators {
> +			sw1a_reg: sw1ab {
> +				regulator-min-microvolt = <300000>;
> +				regulator-max-microvolt = <1875000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <6250>;
> +			};
> +
> +			sw1c_reg: sw1c {
> +				regulator-min-microvolt = <300000>;
> +				regulator-max-microvolt = <1875000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +				regulator-ramp-delay = <6250>;
> +			};
> +
> +			sw2_reg: sw2 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3950000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			sw3a_reg: sw3a {
> +				regulator-min-microvolt = <400000>;
> +				regulator-max-microvolt = <1975000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			sw3b_reg: sw3b {
> +				regulator-min-microvolt = <400000>;
> +				regulator-max-microvolt = <1975000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			sw4_reg: sw4 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +
> +			swbst_reg: swbst {
> +				regulator-min-microvolt = <5000000>;
> +				regulator-max-microvolt = <5150000>;
> +			};
> +
> +			snvs_reg: vsnvs {
> +				regulator-min-microvolt = <1000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vref_reg: vrefddr {
> +				regulator-boot-on;
> +				regulator-always-on;
> +			};
> +
> +			vgen1_reg: vgen1 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1550000>;
> +			};
> +
> +			vgen2_reg: vgen2 {
> +				regulator-min-microvolt = <800000>;
> +				regulator-max-microvolt = <1550000>;
> +			};
> +
> +			vgen3_reg: vgen3 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +			};
> +
> +			vgen4_reg: vgen4 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			vgen5_reg: vgen5 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +
> +			vgen6_reg: vgen6 {
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <3300000>;
> +				regulator-always-on;
> +			};
> +		};
> +	};
> +};
> +
> +&ldb {
> +	status = "okay";
> +
> +	lvds0: lvds-channel at 0 {
> +		status = "okay";
> +
> +		port at 4 {
> +			reg = <4>;
> +
> +			lvds0_out: endpoint {
> +				remote-endpoint = <&panel_in_lvds0>;
> +			};
> +		};
> +	};
> +};
> +
> +&pwm2 {
> +	#pwm-cells = <3>;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_pwm2>;
> +	status = "okay";
> +};
> +
> +&ssi2 {
> +	status = "okay";
> +};
> +
> +&uart4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart4>;
> +	uart-has-rtscts;
> +	status = "okay";
> +};
> +
> +&uart5 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_uart5>;
> +	status = "okay";
> +};
> +
> +&usbh1 {
> +	vbus-supply = <&reg_usbh1_vbus>;
> +	dr_mode = "host";
> +	status = "okay";
> +};
> +
> +&usdhc4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc4>;
> +	bus-width = <8>;
> +	non-removable;
> +	status = "okay";
> +};
> +
> +&iomuxc {
> +	pinctrl-names = "default";
> +
> +	pinctrl_audmux: audmuxgrp {
> +		fsl,pins = <
> +			/* I2S OUTPUT AUD6*/
> +			MX6QDL_PAD_DI0_PIN4__AUD6_RXD  0x130b0
> +			MX6QDL_PAD_DI0_PIN2__AUD6_TXD  0x130b0
> +			MX6QDL_PAD_DI0_PIN3__AUD6_TXFS  0x130b0
> +			MX6QDL_PAD_DI0_PIN15__AUD6_TXC  0x130b0
> +		>;
> +	};
> +
> +	pinctrl_backlight: dispgrp {
> +		fsl,pins = <
> +			/* BLEN_OUT */
> +			MX6QDL_PAD_DISP0_DAT13__GPIO5_IO07    0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_ecspi2: ecspi2grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_CSI0_DAT10__ECSPI2_MISO	0x100b1
> +			MX6QDL_PAD_CSI0_DAT9__ECSPI2_MOSI	0x100b1
> +			MX6QDL_PAD_CSI0_DAT8__ECSPI2_SCLK	0x100b1
> +		>;
> +	};
> +
> +	pinctrl_ecspi2_cs: ecspi2csgrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_CSI0_DAT11__GPIO5_IO29 0x100b1
> +		>;
> +	};
> +
> +	pinctrl_ecspi2_flwp: ecspi2flwpgrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_ecspi3: ecspi3grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO	0x100b1
> +			MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI	0x100b1
> +			MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK	0x100b1
> +		>;
> +	};
> +
> +	pinctrl_ecspi3_cs: ecspi3csgrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_ecspi3_flwp: ecspi3flwpgrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_DISP0_DAT6__GPIO4_IO27 0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_enet: enetgrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
> +			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
> +			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b0b0
> +			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
> +			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
> +			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
> +			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
> +			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
> +			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
> +			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
> +			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
> +			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
> +			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
> +			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
> +			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
> +			MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8
> +			MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
> +			MX6QDL_PAD_ENET_RXD0__GPIO1_IO27        0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_i2c1: i2c1grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_EIM_D21__I2C1_SCL	0x4001b8b1
> +			MX6QDL_PAD_EIM_D28__I2C1_SDA	0x4001b8b1
> +		>;
> +	};
> +
> +	pinctrl_i2c2: i2c2grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_EIM_EB2__I2C2_SCL	0x4001b8b1
> +			MX6QDL_PAD_EIM_D16__I2C2_SDA	0x4001b8b1
> +		>;
> +	};
> +
> +	pinctrl_i2c3: i2c3grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_EIM_D17__I2C3_SCL	0x4001b8b1
> +			MX6QDL_PAD_EIM_D18__I2C3_SDA	0x4001b8b1
> +		>;
> +	};
> +
> +	pinctrl_pwm2: pwm2grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_DISP0_DAT9__PWM2_OUT	0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_reg_lvds: reqlvdsgrp {
> +		fsl,pins = <
> +			/* LVDS_PPEN_OUT */
> +			MX6QDL_PAD_DISP0_DAT19__GPIO5_IO13      0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_uart4: uart4grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_CSI0_DAT12__UART4_TX_DATA	0x1b0b1
> +			MX6QDL_PAD_CSI0_DAT13__UART4_RX_DATA	0x1b0b1
> +			MX6QDL_PAD_CSI0_DAT16__UART4_RTS_B	0x1b0b1
> +			MX6QDL_PAD_CSI0_DAT17__UART4_CTS_B	0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_uart5: uart5grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_CSI0_DAT14__UART5_TX_DATA	0x1b0b1
> +			MX6QDL_PAD_CSI0_DAT15__UART5_RX_DATA    0x1b0b1
> +		>;
> +	};
> +
> +	pinctrl_usbh1_vbus: usbh1grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_EIM_D31__USB_H1_PWR 0x130b0
> +			MX6QDL_PAD_EIM_D30__USB_H1_OC  0x030b0
> +		>;
> +	};
> +
> +	pinctrl_usdhc4: usdhc4grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
> +			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
> +			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
> +			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
> +			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
> +			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
> +			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
> +			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
> +			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
> +			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
> +			MX6QDL_PAD_NANDF_ALE__SD4_RESET	0x17059
> +		>;
> +	};
> +};
> 


-- 
Best regards,

Lukasz Majewski

--

DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de



More information about the linux-arm-kernel mailing list