[PATCH v3] ARM: dts: at91: sama5d2: add m_can nodes

[Yang, Wenyou]

On 2017/4/24 9:12, Wenyou Yang wrote:
> Add nodes to support the Controller Area Network(M_CAN) on SAMA5D2.
> The version of M_CAN IP core is 3.1.0 (CREL = 0x31040730).
>
> As said in SAMA5D2 datasheet, the CAN clock is recommended to use
> frequencies of 20, 40 or 80 MHz. To achieve these frequencies,
> PMC GCLK3 must select the UPLLCK(480 MHz) as source clock and
> divide by 24, 12, or 6. So, the "assigned-clock-rates" property
> has three options: 20000000, 40000000, and 80000000.
> The "assigned-clock-parents" property should be referred to utmi
> fixedly.
>
> The MSBs [bits 31:16] of the CAN Message RAM for CAN0 and CAN1 are
> default configured in 0x00200000. To avoid conflict with SRAM map
> for PM, change them to 0x00210000 in the AT91Bootstrap via setting
> the CAN Memories Address-based Register(SFR_CAN) of SFR.
>
> Signed-off-by: Wenyou Yang <wenyou.yang at atmel.com>
> Tested-by: Quentin Schulz <quentin.schulz at free-electrons.com>

Do you have any comments?
> ---
> The patch is tested on SAMA5D2 Xplained and based on the patch set,
>   1. [PATCH v4 1/7] can: m_can: Disabled Interrupt Line 1
>      http://marc.info/?l=linux-can&m=149165343604033&w=2
>
> Changes in v3:
>   - Add Tested-by tag.
>   - Change the number of Rx Rx Buffers, Tx Buffers and Tx Event FIFO
>     to maximum.
>
> Changes in v2:
>   - Configures 10 TX Event FIFO elements and 10 TX Buffers/FIFO slots,
>     because the TXE FIFO is needed to be configured.
>   - Configure the offset of Message RAM for CAN1 followed from CAN0's.
>
>   arch/arm/boot/dts/at91-sama5d2_xplained.dts | 24 +++++++++++++
>   arch/arm/boot/dts/sama5d2.dtsi              | 56 +++++++++++++++++++++++++++++
>   2 files changed, 80 insertions(+)
>
> diff --git a/arch/arm/boot/dts/at91-sama5d2_xplained.dts b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
> index 9f7f8a7d8ff9..2f19b08dc226 100644
> --- a/arch/arm/boot/dts/at91-sama5d2_xplained.dts
> +++ b/arch/arm/boot/dts/at91-sama5d2_xplained.dts
> @@ -257,6 +257,12 @@
>   				status = "okay";
>   			};
>   
> +			can0: can at f8054000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&pinctrl_can0_default>;
> +				status = "okay";
> +			};
> +
>   			uart3: serial at fc008000 {
>   				atmel,use-dma-rx;
>   				atmel,use-dma-tx;
> @@ -321,6 +327,18 @@
>   					bias-disable;
>   				};
>   
> +				pinctrl_can0_default: can0_default {
> +					pinmux = <PIN_PC10__CANTX0>,
> +						 <PIN_PC11__CANRX0>;
> +					bias-disable;
> +				};
> +
> +				pinctrl_can1_default: can1_default {
> +					pinmux = <PIN_PC26__CANTX1>,
> +						 <PIN_PC27__CANRX1>;
> +					bias-disable;
> +				};
> +
>   				pinctrl_charger_chglev: charger_chglev {
>   					pinmux = <PIN_PA12__GPIO>;
>   					bias-disable;
> @@ -468,6 +486,12 @@
>   				};
>   
>   			};
> +
> +			can1: can at fc050000 {
> +				pinctrl-names = "default";
> +				pinctrl-0 = <&pinctrl_can1_default>;
> +				status = "okay";
> +			};
>   		};
>   	};
>   
> diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
> index 22332be72140..7e00fa21373e 100644
> --- a/arch/arm/boot/dts/sama5d2.dtsi
> +++ b/arch/arm/boot/dts/sama5d2.dtsi
> @@ -762,6 +762,18 @@
>   						atmel,clk-output-range = <0 83000000>;
>   					};
>   
> +					can0_clk: can0_clk {
> +						#clock-cells = <0>;
> +						reg = <56>;
> +						atmel,clk-output-range = <0 83000000>;
> +					};
> +
> +					can1_clk: can1_clk {
> +						#clock-cells = <0>;
> +						reg = <57>;
> +						atmel,clk-output-range = <0 83000000>;
> +					};
> +
>   					classd_clk: classd_clk {
>   						#clock-cells = <0>;
>   						reg = <59>;
> @@ -890,6 +902,18 @@
>   						#clock-cells = <0>;
>   						reg = <55>;
>   					};
> +
> +					can0_gclk: can0_gclk {
> +						#clock-cells = <0>;
> +						reg = <56>;
> +						atmel,clk-output-range = <0 80000000>;
> +					};
> +
> +					can1_gclk: can1_gclk {
> +						#clock-cells = <0>;
> +						reg = <57>;
> +						atmel,clk-output-range = <0 80000000>;
> +					};
>   				};
>   			};
>   
> @@ -1144,6 +1168,22 @@
>   				clocks = <&clk32k>;
>   			};
>   
> +			can0: can at f8054000 {
> +				compatible = "bosch,m_can";
> +				reg = <0xf8054000 0x4000>, <0x210000 0x4000>;
> +				reg-names = "m_can", "message_ram";
> +				interrupts = <56 IRQ_TYPE_LEVEL_HIGH 7>,
> +					     <64 IRQ_TYPE_LEVEL_HIGH 7>;
> +				interrupt-names = "int0", "int1";
> +				clocks = <&can0_clk>, <&can0_gclk>;
> +				clock-names = "hclk", "cclk";
> +				assigned-clocks = <&can0_gclk>;
> +				assigned-clock-parents = <&utmi>;
> +				assigned-clock-rates = <40000000>;
> +				bosch,mram-cfg = <0x0 0 0 64 0 0 32 32>;
> +				status = "disabled";
> +			};
> +
>   			spi1: spi at fc000000 {
>   				compatible = "atmel,at91rm9200-spi";
>   				reg = <0xfc000000 0x100>;
> @@ -1305,6 +1345,22 @@
>   				status = "okay";
>   			};
>   
> +			can1: can at fc050000 {
> +				compatible = "bosch,m_can";
> +				reg = <0xfc050000 0x4000>, <0x210000 0x4000>;
> +				reg-names = "m_can", "message_ram";
> +				interrupts = <57 IRQ_TYPE_LEVEL_HIGH 7>,
> +					     <65 IRQ_TYPE_LEVEL_HIGH 7>;
> +				interrupt-names = "int0", "int1";
> +				clocks = <&can1_clk>, <&can1_gclk>;
> +				clock-names = "hclk", "cclk";
> +				assigned-clocks = <&can1_gclk>;
> +				assigned-clock-parents = <&utmi>;
> +				assigned-clock-rates = <40000000>;
> +				bosch,mram-cfg = <0x1100 0 0 64 0 0 32 32>;
> +				status = "disabled";
> +			};
> +
>   			chipid at fc069000 {
>   				compatible = "atmel,sama5d2-chipid";
>   				reg = <0xfc069000 0x8>;

Best Regards,
Wenyou Yang