[PATCH] ARM64: dts: meson-gxbb-odroidc2: enable USB Host Nodes

Anand Moon linux.amoon at gmail.com
Fri Mar 10 22:48:47 PST 2017


Hi Martin,

On 10 March 2017 at 01:06, Martin Blumenstingl
<martin.blumenstingl at googlemail.com> wrote:
> Hi Anand,
>
> On Thu, Mar 9, 2017 at 6:58 PM, Anand Moon <linux.amoon at gmail.com> wrote:
>>> Hi Anand,
>>>
>>> For this specific use case, the only way to manage this is to use the Work-In-Progress
>>> Power Sequence Library proposer by Peter Chen at :
>>> https://lkml.org/lkml/2016/11/13/315
>>>
>>> Since this is the USB Hub reset link and has no direct link with either the USB controller
>>> or the USB PHY, and the USB Hus cannot be modeled (yet ?) in the DT.
>>>
>>> One intermediate, but crappy, solution would be to add a GPIO hog until the power
>>> sequence code has been merged, with a proper big fat warning in the dts file.
>>>
>>> You can find doc about the gpio-hog in :
>>> Documentation/devicetree/bindings/gpio/gpio.txt
>>>
>>> It should look like :
>>>
>>> usb-hub {
>>>         gpio-hog;
>>>         gpios = <GPIOAO_4 GPIO_ACTIVE_HIGH>;
>>>         output-high;
>>>         line-name = "usb-hub-reset";
>>> };
>>>
>>> in the gpio_ao controller node.
>>>
>>> Neil
>>
>> Thanks for this input.
>>
>> I will check this series of patches, and work on this new approach.
> you might want to look at the following two patches as well: [0] and [1]
> I didn't test them as I don't have an Odroid-C2 but they should work
> with the series that Neil has mentioned. feel free to take my patches
> and fix them where needed
>
>
> Regards,
> Martin
>
> [0] https://github.com/xdarklight/linux/commit/f0bc8f826b465fbf24279ce78654b65282790dc6
> [1] https://github.com/xdarklight/linux/commit/7b5a69bf5bad992249aa39a96360fe90ccde9cd5

As pointed by Neil

For this specific use case, the only way to manage this is to use the
Work-In-Progress
Power Sequence Library proposer by Peter Chen at :
https://lkml.org/lkml/2017/1/5/33 (updated v11)

Using above series I was able to get the usb nodes to work correctly
on Odroid C2.
Although the series of patches did not clean apply completely.

I manage to get this working with your above patches. I will submit
the patches soon.

root at odroid64:~# lsusb -t
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/4p, 480M
        |__ Port 1: Dev 3, If 0, Class=Human Interface Device,
Driver=usbhid, 1.5M
        |__ Port 1: Dev 3, If 1, Class=Human Interface Device,
Driver=usbhid, 1.5M
        |__ Port 2: Dev 4, If 0, Class=Mass Storage, Driver=usb-storage, 480M
        |__ Port 4: Dev 5, If 0, Class=Mass Storage, Driver=usb-storage, 480M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=dwc2/1p, 480M
root at odroid64:~#


Best Regards
-Anand Moon



More information about the linux-arm-kernel mailing list