[PATCH v8 0/3] Support for USB DRD PHY driver for NS2

Kishon Vijay Abraham I kishon at ti.com
Fri Jun 9 01:55:21 PDT 2017


Hi,

On Thursday 08 June 2017 04:05 PM, Raviteja Garimella wrote:
> Changes in v8:
> =============
> -Renamed phy shutdown routine
> -Used devm_request_irq in stead of threaded irq

That's not what I intended. Continue to use threaded irq but remove delayed work.

Thanks
Kishon
> -Removed devm_unregister calls in probe routine
> 
> Changes in v7:
> =============
> Cleaned up unused variables in phy private data structure that's
> missed out in v6.
> Setting of phy mode to device/host is removed from phy power on.
> routine.
> 
> Changes in v6:
> =============
> Removed spin locks which are not required as the references
> to phy_ops in the same driver were removed in v5.
> 
> Removed host/device 'notify' routines which are registered
> using 'extcon_register_notifier'. The irq handler is sufficient
> to deal with the change in extcon events within the same driver.
> 
> Changes in v5:
> =============
> Removed references to phy_ops in the same driver by connect_work
> event handler to change the phy modes.
> 
> To support dynamically changing the mode of the phy, it does
> not require doing a phy reset/programming of PHY PLL. Changes
> are made to the connect_work routine to just program the required
> register bits to achieve this purpose.
> 
> Changes in v4:
> =============
> Remove references to edev->name in debug prints.
> 
> Changes in v3:
> =============
> Remove unnecessary checks for poweron as suggested in review.
> 
> Changes in v2:
> =============
> 1. Initialize file operations .owner field with THIS_MODULE.
> 2. Remove unnecessary gpio example in DT bindings documentation.
>    This is previously acked by Rob Herring <robh at kernel.org>
> 
> Introduction for PATCH v1:
> 
> This patch adds support for USB Dual Role Device Phy for Broadcom
> Northstar2 SoC. Apart from the new phy driver, this patchset contains
> changes to Kconfig, Makefile, and Device tree files.
> 
> This patchset is tested on Broadcom NS2 BCM958712K reference board.
> 
> Repo: https://github.com/Broadcom/arm64-linux.git
> Branch: ns2_drdphy_v8
> 
> Raviteja Garimella (3):
>   dt-bindings: phy: Add DT bindings documentation for NS2 USB DRD PHY
>   phy: phy-bcm-ns2-usbdrd: Broadcom USB DRD PHY driver for Northstar2
>   arm64: dts: NS2: Add USB DRD PHY device tree node
> 
>  .../devicetree/bindings/phy/brcm,ns2-drd-phy.txt   |  30 ++
>  arch/arm64/boot/dts/broadcom/ns2.dtsi              |  14 +
>  drivers/phy/Kconfig                                |  13 +
>  drivers/phy/Makefile                               |   1 +
>  drivers/phy/phy-bcm-ns2-usbdrd.c                   | 437 +++++++++++++++++++++
>  5 files changed, 495 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt
>  create mode 100644 drivers/phy/phy-bcm-ns2-usbdrd.c
> 



More information about the linux-arm-kernel mailing list