[PATCH v2 5/5] arm64: dts: rockchip: update the thermal zones for RK3399 SoCs

Heiko Stuebner heiko at sntech.de
Sat Jul 22 14:48:16 PDT 2017


Hi Caesar,

Am Montag, 17. Juli 2017, 16:14:31 CEST schrieb Caesar Wang:
> As RK3399 had used the Power allocator thermal governor by default,
> enabled this to manage thermals by dynamically allocating and limiting
> power to devices.
> 
> Also, this patch supported the dynamic-power-coefficient/sustainable_power
> and GPU's power model for needed parameters with thermal IPA.
> 
> The Thermal power allocator governor works optimatly with two passive trip
> points, for the better performance we will use the trip-point0 with 70
> degree above which the governor control starts operating and trip-point1
> with 85 degree is the target temperature by controlling.
> 
> Signed-off-by: Caesar Wang <wxt at rock-chips.com>
> 
> ---
> 
> Changes in v2:
> - foo@ will produce warnings when used without reg property.
> - update the commit to explain the two passive trip points changed.
> 
>  arch/arm64/boot/dts/rockchip/rk3399.dtsi | 62 +++++++++++++++-----------------
>  1 file changed, 29 insertions(+), 33 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
> index 77d67cb..6d8a5eb 100644
> --- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
> +++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
> @@ -147,7 +147,7 @@
>  			enable-method = "psci";
>  			#cooling-cells = <2>; /* min followed by max */
>  			clocks = <&cru ARMCLKB>;
> -			dynamic-power-coefficient = <100>;
> +			dynamic-power-coefficient = <436>;
>  		};
>  
>  		cpu_b1: cpu at 101 {
> @@ -156,7 +156,7 @@
>  			reg = <0x0 0x101>;
>  			enable-method = "psci";
>  			clocks = <&cru ARMCLKB>;
> -			dynamic-power-coefficient = <100>;
> +			dynamic-power-coefficient = <436>;

Adjusting the coefficients should be a separate patch and the
commit message should explain how they were calculated and
why they are the exacter ones over the old values.


>  		};
>  	};
>  
> @@ -690,24 +690,25 @@
>  	};
>  
>  	thermal_zones: thermal-zones {
> -		cpu_thermal: cpu {
> +		soc_thermal: soc-thermal {
>  			polling-delay-passive = <100>;
>  			polling-delay = <1000>;
> +			sustainable-power = <1000>;
>  
>  			thermal-sensors = <&tsadc 0>;
>  
>  			trips {
> -				cpu_alert0: cpu_alert0 {
> +				threshold: trip-point0 {
>  					temperature = <70000>;
>  					hysteresis = <2000>;
>  					type = "passive";
>  				};
> -				cpu_alert1: cpu_alert1 {
> -					temperature = <75000>;
> +				target: trip-point1 {
> +					temperature = <85000>;
>  					hysteresis = <2000>;
>  					type = "passive";
>  				};
> -				cpu_crit: cpu_crit {
> +				soc_crit: soc-crit {
>  					temperature = <95000>;
>  					hysteresis = <2000>;
>  					type = "critical";
> @@ -716,45 +717,31 @@
>  
>  			cooling-maps {
>  				map0 {
> -					trip = <&cpu_alert0>;
> +					trip = <&target>;

still both maps use &target as trip point. Is that intentional
and if so, why is the &threshold trip point never referenced?


>  					cooling-device =
> -						<&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +						<&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +					contribution = <4096>;
>  				};
>  				map1 {
> -					trip = <&cpu_alert1>;
> +					trip = <&target>;
>  					cooling-device =
> -						<&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
>  						<&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +					contribution = <1024>;
> +				};
> +				map2 {
> +					trip = <&target>;
> +					cooling-device =
> +						<&gpu THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> +					contribution = <4096>;
>  				};
>  			};
>  		};
>  
> -		gpu_thermal: gpu {
> +		gpu_thermal: gpu-thermal {
>  			polling-delay-passive = <100>;
>  			polling-delay = <1000>;
>  
>  			thermal-sensors = <&tsadc 1>;
> -
> -			trips {
> -				gpu_alert0: gpu_alert0 {
> -					temperature = <75000>;
> -					hysteresis = <2000>;
> -					type = "passive";
> -				};
> -				gpu_crit: gpu_crit {
> -					temperature = <95000>;
> -					hysteresis = <2000>;
> -					type = "critical";
> -				};
> -			};
> -
> -			cooling-maps {
> -				map0 {
> -					trip = <&gpu_alert0>;
> -					cooling-device =
> -						<&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
> -				};
> -			};
>  		};
>  	};
>  
> @@ -1451,8 +1438,17 @@
>  			     <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH 0>;
>  		interrupt-names = "gpu", "job", "mmu";
>  		clocks = <&cru ACLK_GPU>;
> +		#cooling-cells = <2>;
>  		power-domains = <&power RK3399_PD_GPU>;
>  		status = "disabled";
> +
> +		gpu_power_model: power_model {
> +			compatible = "arm,mali-simple-power-model";
> +			static-coefficient = <1079403>;
> +			dynamic-coefficient = <977>;
> +			ts = <32000 4700 (-80) 2>;
> +			thermal-zone = "gpu-thermal";
> +		};

You might want to have the gpu thermal work without the
power-model-thingy for now, so most likely just drop that
gpu-related change for now.


Heiko



More information about the linux-arm-kernel mailing list