[PATCH 1/1] ARM64: dts: meson-gxl: improve support for the P212 reference design

Neil Armstrong narmstrong at baylibre.com
Tue Feb 28 05:50:44 PST 2017


On 02/19/2017 11:41 PM, Martin Blumenstingl wrote:
> The Amlogic P212 reference design is used by other devices as well, such
> as (for example) the Khadas VIM boards. Thus this patch adds and moves
> all common entries from meson-gxl-s905x-p212.dts to a new, separate
> meson-gxl-s905x-p212.dtsi (which can be re-used on boards such as the
> Khadas VIM).
> Support for all boards based on the P212 reference design includes:
> - enabling IR support
> - enabling the SAR ADC (SARADC_CH1 is connected to a resistor which
>   indicates the hardware revision, a similar design is found on the
>   Khadas VIM boards)
> - all MMC controllers (which means that SDIO wifi, the SD card and the
>   eMMC are now supported)
> - pwm_ef as dependency for the SDIO wifi module
> - uart_A which is connected to the bluetooth module (the bluetooth
>   module itself is not enabled yet due to missing devicetree bindings
>   for the Broadcom serial bluetooth devices)
> - uart_AO is moved to the .dtsi (as all known devices use it as their
>   boot-console)
> 
> Specific to the P212 board:
> - this also enables the CVBS connector (which is not available on the
>   Khadas VIM boards for example)
> 
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl at googlemail.com>
> ---
>  .../boot/dts/amlogic/meson-gxl-s905x-p212.dts      |  21 +-
>  .../boot/dts/amlogic/meson-gxl-s905x-p212.dtsi     | 214 +++++++++++++++++++++
>  2 files changed, 226 insertions(+), 9 deletions(-)
>  create mode 100644 arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
> 
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts
> index 9639f012b02b..db31e093f40e 100644
> --- a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dts
> @@ -43,23 +43,26 @@
>  
>  /dts-v1/;
>  
> -#include "meson-gxl-s905x.dtsi"
> +#include "meson-gxl-s905x-p212.dtsi"
>  
>  / {
>  	compatible = "amlogic,p212", "amlogic,s905x", "amlogic,meson-gxl";
>  	model = "Amlogic Meson GXL (S905X) P212 Development Board";
>  
> -	aliases {
> -		serial0 = &uart_AO;
> -	};
> +	cvbs-connector {
> +		compatible = "composite-video-connector";
>  
> -	chosen {
> -		stdout-path = "serial0:115200n8";
> +		port {
> +			cvbs_connector_in: endpoint {
> +				remote-endpoint = <&cvbs_vdac_out>;
> +			};
> +		};
>  	};
> +};
>  
> -	memory at 0 {
> -		device_type = "memory";
> -		reg = <0x0 0x0 0x0 0x80000000>;
> +&cvbs_vdac_port {
> +	cvbs_vdac_out: endpoint {
> +		remote-endpoint = <&cvbs_connector_in>;
>  	};
>  };
>  
> diff --git a/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
> new file mode 100644
> index 000000000000..fb0e7c999cb6
> --- /dev/null
> +++ b/arch/arm64/boot/dts/amlogic/meson-gxl-s905x-p212.dtsi
> @@ -0,0 +1,214 @@
> +/*
> + * Copyright (c) 2016 Martin Blumenstingl <martin.blumenstingl at googlemail.com>.
> + * Based on meson-gx-p23x-q20x.dtsi:
> + * - Copyright (c) 2016 Endless Computers, Inc.
> + *   Author: Carlo Caione <carlo at endlessm.com>
> + * - Copyright (c) 2016 BayLibre, SAS.
> + *   Author: Neil Armstrong <narmstrong at baylibre.com>
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This library is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This library is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/* Common DTSI for devices which are based on the P212 reference board. */
> +
> +#include "meson-gxl-s905x.dtsi"
> +
> +/ {
> +	aliases {
> +		serial0 = &uart_AO;
> +		serial1 = &uart_A;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	memory at 0 {
> +		device_type = "memory";
> +		reg = <0x0 0x0 0x0 0x80000000>;
> +	};
> +
> +	vddio_boot: regulator-vddio_boot {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_BOOT";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	vddao_3v3: regulator-vddao_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDAO_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	vddio_ao18: regulator-vddio_ao18 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VDDIO_AO18";
> +		regulator-min-microvolt = <1800000>;
> +		regulator-max-microvolt = <1800000>;
> +	};
> +
> +	vcc_3v3: regulator-vcc_3v3 {
> +		compatible = "regulator-fixed";
> +		regulator-name = "VCC_3V3";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +	};
> +
> +	emmc_pwrseq: emmc-pwrseq {
> +		compatible = "mmc-pwrseq-emmc";
> +		reset-gpios = <&gpio BOOT_9 GPIO_ACTIVE_LOW>;
> +	};
> +
> +	wifi32k: wifi32k {
> +		compatible = "pwm-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <32768>;
> +		pwms = <&pwm_ef 0 30518 0>; /* PWM_E at 32.768KHz */
> +	};
> +
> +	sdio_pwrseq: sdio-pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&gpio GPIOX_6 GPIO_ACTIVE_LOW>;
> +		clocks = <&wifi32k>;
> +		clock-names = "ext_clock";
> +	};
> +};
> +
> +&ethmac {
> +	status = "okay";
> +};
> +
> +&ir {
> +	status = "okay";
> +	pinctrl-0 = <&remote_input_ao_pins>;
> +	pinctrl-names = "default";
> +};
> +
> +&saradc {
> +	status = "okay";
> +	vref-supply = <&vddio_ao18>;
> +};
> +
> +/* Wireless SDIO Module */
> +&sd_emmc_a {
> +	status = "okay";
> +	pinctrl-0 = <&sdio_pins>;
> +	pinctrl-names = "default";
> +	#address-cells = <1>;
> +	#size-cells = <0>;
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <100000000>;
> +
> +	non-removable;
> +	disable-wp;
> +
> +	mmc-pwrseq = <&sdio_pwrseq>;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +
> +	brcmf: bcrmf at 1 {
> +		reg = <1>;
> +		compatible = "brcm,bcm4329-fmac";
> +	};
> +};
> +
> +/* SD card */
> +&sd_emmc_b {
> +	status = "okay";
> +	pinctrl-0 = <&sdcard_pins>;
> +	pinctrl-names = "default";
> +
> +	bus-width = <4>;
> +	cap-sd-highspeed;
> +	max-frequency = <100000000>;
> +	disable-wp;
> +
> +	cd-gpios = <&gpio CARD_6 GPIO_ACTIVE_HIGH>;
> +	cd-inverted;
> +
> +	vmmc-supply = <&vddao_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +/* eMMC */
> +&sd_emmc_c {
> +	status = "okay";
> +	pinctrl-0 = <&emmc_pins>;
> +	pinctrl-names = "default";
> +
> +	bus-width = <8>;
> +	cap-sd-highspeed;
> +	cap-mmc-highspeed;
> +	max-frequency = <200000000>;
> +	non-removable;
> +	disable-wp;
> +	mmc-ddr-1_8v;
> +	mmc-hs200-1_8v;
> +
> +	mmc-pwrseq = <&emmc_pwrseq>;
> +	vmmc-supply = <&vcc_3v3>;
> +	vqmmc-supply = <&vddio_boot>;
> +};
> +
> +&pwm_ef {
> +	status = "okay";
> +	pinctrl-0 = <&pwm_e_pins>;
> +	pinctrl-names = "default";
> +	clocks = <&clkc CLKID_FCLK_DIV4>;
> +	clock-names = "clkin0";
> +};
> +
> +/* This is connected to the Bluetooth module: */
> +&uart_A {
> +	status = "okay";
> +	pinctrl-0 = <&uart_a_pins>, <&uart_a_cts_rts_pins>;
> +	pinctrl-names = "default";
> +	uart-has-rtscts;
> +};
> +
> +&uart_AO {
> +	status = "okay";
> +	pinctrl-0 = <&uart_ao_a_pins>;
> +	pinctrl-names = "default";
> +};
> 

Great Job !

It works perfectly on an P212 board.

Tested-by: Neil Armstrong <narmstrong at baylibre.com>

Thanks,
Neil



More information about the linux-arm-kernel mailing list