[PATCH] drm: hdlcd: allow HDLCD to be used without interrupt

Liviu Dudau liviu.dudau at arm.com
Tue Aug 29 06:33:52 PDT 2017


On Fri, Jul 28, 2017 at 04:58:27PM +0100, Russell King - ARM Linux wrote:
> On Fri, Jul 28, 2017 at 04:23:11PM +0100, Liviu Dudau wrote:
> > On Wed, Jul 26, 2017 at 11:27:48AM +0100, Russell King - ARM Linux wrote:
> > > On Wed, Jul 26, 2017 at 11:05:39AM +0100, Russell King wrote:
> > > > Some ARM platforms do not wire the HDLCD interrupt.  Allow hdlcd to
> > > > initialise without an interrupt present.
> > > > 
> > > > Signed-off-by: Russell King <rmk+kernel at armlinux.org.uk>
> > > 
> > 
> > Hi Russell,
> > 
> > Sorry for my silence, I was on holiday this week and just came back
> > today.
> > 
> > > This isn't fully functional on ARM MPS platforms yet, but at least
> > > gets us further.  Without any display connected:
> > > 
> > > [   14.315986] [drm] found ARM HDLCD version r0p0
> > > [   14.557038] tda998x 2-0070: found TDA19988
> > > [   14.622232] hdlcd 40205000.hdlcd: bound 2-0070 (ops 0x213534)
> > > [   14.630406] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
> > > [   14.639335] [drm] No driver support for vblank timestamp query.
> > > [   14.653210] [drm] Cannot find any crtc or sizes - going 1024x768
> > > [   15.232556] hdlcd 40205000.hdlcd: fb0:  frame buffer device
> > > [   15.284076] [drm] Initialized hdlcd 1.0.0 20151021 for 40205000.hdlcd on minor 0
> > > 
> > > With a TV connected, the driver doesn't initialise:
> > > 
> > > [   14.422810] [drm] found ARM HDLCD version r0p0
> > > [   14.657227] tda998x 2-0070: found TDA19988
> > > [   14.722439] hdlcd 40205000.hdlcd: bound 2-0070 (ops 0x213534)
> > > [   14.730613] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
> > > [   14.739538] [drm] No driver support for vblank timestamp query.
> > > [   15.311977] hdlcd 40205000.hdlcd: Failed to set initial hw configuration.
> > > [   15.357402] hdlcd 40205000.hdlcd: master bind failed: -12
> > > [   15.365082] tda998x: probe of 2-0070 failed with error -12
> > > 
> > > I don't think this is correct behaviour - if we fail to set an initial
> > > configuration (which will be based on the resolution of the connected
> > > display) why should the driver fail to probe - it's not that there is
> > > no device, it's (in this case) that there aren't the resources for the
> > > chosen mode.  Userspace could always try setting a different mode.
> > > 
> > > I suspect the above failure is down to either (a) not having enough
> > > memory available to allocate a 1920x1080 frame buffer, or (b) not
> > > (yet) being able to program the hdlcd pixel clock for this platform,
> > > which is currently hard-coded in DT at 23.75MHz.
> > 
> > I don't think it is the clock, if that fails then you would not see the
> > r0p0 version number being printed. Due to the fact that until now HDLCD
> > has run mostly on platforms that have SCP, which takes care of actual
> > setup of the clocks, it is pretty lax on errors on pixel clock setup.
> 
> Note, however, that in this case, the clock is a fixed frequency clock.
> I wasn't meaning a failure to obtain the clock, I was meaning a failure
> to set the appropriate rate.
> 
> > Also, may I ask what MPS platform you are trying to use? I might be able
> > to source one internally and try to reproduce your problems.
> 
> I'll point you in the direction of Ian Rickards in ARM for that
> information.  (I'm not sure if I can mention the board publically
> yet as its early days...)

Hi Russell,

I've worked with Vladimir Murzin inside ARM to try to sort out problems
on the board like the one that you have. He's got to a point where the HDLCD
starts correctly after adding a non-fixed pxlclk source, but then the rest of
the setup is semi-useless without a working IRQ because DRM atomic calls
will give you a vblank timeout splat everytime you invoke them. So I'm
not sure how you want to progress with this patch, as not having an IRQ
line means you will not get any vblank interrupts and you can't use the
driver with userspace that calls DRM API.

The RTL guys are apparently working on a fix, but I have no ETA or
details on when they are going to do.

Best regards,
Liviu

> 
> -- 
> RMK's Patch system: http://www.armlinux.org.uk/developer/patches/
> FTTC broadband for 0.8mile line: currently at 9.6Mbps down 400kbps up
> according to speedtest.net.

-- 
====================
| I would like to |
| fix the world,  |
| but they're not |
| giving me the   |
 \ source code!  /
  ---------------
    ¯\_(ツ)_/¯



More information about the linux-arm-kernel mailing list