[PATCH v2] ARM: dts: da850: add the mstpri and ddrctl nodes

Kevin Hilman khilman at baylibre.com
Sun Nov 27 22:16:42 PST 2016


On Wed, Nov 23, 2016 at 9:03 PM, Sekhar Nori <nsekhar at ti.com> wrote:
> On Thursday 24 November 2016 04:18 AM, David Lechner wrote:
>> On 11/23/2016 04:32 PM, Kevin Hilman wrote:
>>> David Lechner <david at lechnology.com> writes:
>>>
>>>> On 11/23/2016 04:27 AM, Bartosz Golaszewski wrote:
>>>>> 2016-11-22 23:23 GMT+01:00 David Lechner <david at lechnology.com>:
>>>>>> On 11/15/2016 05:00 AM, Bartosz Golaszewski wrote:
>>>>>>>
>>>>>>> Add the nodes for the MSTPRI configuration and DDR2/mDDR memory
>>>>>>> controller drivers to da850.dtsi.
>>>>>>>
>>>>>>> Signed-off-by: Bartosz Golaszewski <bgolaszewski at baylibre.com>
>>>>>>> ---
>>>>>>> v1 -> v2:
>>>>>>> - moved the priority controller node above the cfgchip node
>>>>>>> - renamed added nodes to better reflect their purpose
>>>>>>>
>>>>>>>  arch/arm/boot/dts/da850.dtsi | 8 ++++++++
>>>>>>>  1 file changed, 8 insertions(+)
>>>>>>>
>>>>>>> diff --git a/arch/arm/boot/dts/da850.dtsi
>>>>>>> b/arch/arm/boot/dts/da850.dtsi
>>>>>>> index 1bb1f6d..412eec6 100644
>>>>>>> --- a/arch/arm/boot/dts/da850.dtsi
>>>>>>> +++ b/arch/arm/boot/dts/da850.dtsi
>>>>>>> @@ -210,6 +210,10 @@
>>>>>>>                         };
>>>>>>>
>>>>>>>                 };
>>>>>>> +               prictrl: priority-controller at 14110 {
>>>>>>> +                       compatible = "ti,da850-mstpri";
>>>>>>> +                       reg = <0x14110 0x0c>;
>>>>>>
>>>>>>
>>>>>> I think we should add status = "disabled"; here and let boards opt in.
>>>>>>
>>>>>>> +               };
>>>>>>>                 cfgchip: chip-controller at 1417c {
>>>>>>>                         compatible = "ti,da830-cfgchip", "syscon",
>>>>>>> "simple-mfd";
>>>>>>>                         reg = <0x1417c 0x14>;
>>>>>>> @@ -451,4 +455,8 @@
>>>>>>>                           1 0 0x68000000 0x00008000>;
>>>>>>>                 status = "disabled";
>>>>>>>         };
>>>>>>> +       memctrl: memory-controller at b0000000 {
>>>>>>> +               compatible = "ti,da850-ddr-controller";
>>>>>>> +               reg = <0xb0000000 0xe8>;
>>>>>>
>>>>>>
>>>>>> same here. status = "disabled";
>>>>>>
>>>>>>> +       };
>>>>>>>  };
>>>>>>>
>>>>>
>>>>> Hi David,
>>>>>
>>>>> I did that initially[1][2] and it was rejected by Kevin[3] and
>>>>> Laurent[4].
>>>>>
>>>>> FYI this patch has already been queued by Sekhar.
>>>>
>>>> Thanks. I did not see those threads.
>>>>
>>>> FYI to maintainers, having these enabled by default causes error
>>>> messages in the kernel log for other boards that are not supported by
>>>> the drivers.
>>>
>>> Then the driver is too noisy and should be cleaned up.
>>>
>>>> Since there is only one board that is supported and soon
>>>> to be 2 that are not, I would rather have this disabled by default to
>>>> avoid the error messages.
>>>
>>> IMO, what exactly are the error messages? Sounds like the driver is
>>> being too verbose, and calling things errors that are not really errors.
>>
>> It is just one line per driver.
>>
>>     dev_err(dev, "no master priorities defined for this board\n");
>>
>> and
>>
>>     dev_err(dev, "no settings defined for this board\n");
>>
>>
>> Since "ti,da850-lcdk" is the only board supported in these drivers, all
>> other boards will see these error messages.
>
> Thats pretty bad. Sorry about that. The original justification for
> keeping them enabled all the time was that they are in-SoC modules with
> no external dependencies (like IO lines or voltage rails) so they can be
> enabled on all boards that use DA850. While that remains true, the
> configuration itself is board specific.
>
> I think the error messages are still useful, so instead of silencing
> them, I think we should go back to keeping these nodes disabled by
> default and enabling only on boards which have support for it in the driver.

I don't have a strong preference for the enabled/disabled by default,
but I think the error messages are not error messages.  It seems
perfectly reasonable for boards to accept the reset (or bootloader)
configuration of these registers, and not consider that an error.

Kevin



More information about the linux-arm-kernel mailing list