[PATCH v4 6/7] net: ethernet: bgmac: add NS2 support
Jon Mason
jon.mason at broadcom.com
Wed Nov 2 09:53:20 PDT 2016
On Tue, Nov 01, 2016 at 05:05:13PM -0400, Jon Mason wrote:
> On Tue, Nov 01, 2016 at 01:34:30PM -0700, Scott Branden wrote:
> > One change in this patch
> >
> > On 16-11-01 01:04 PM, Jon Mason wrote:
> > >Add support for the variant of amac hardware present in the Broadcom
> > >Northstar2 based SoCs. Northstar2 requires an additional register to be
> > >configured with the port speed/duplexity (NICPM). This can be added to
> > >the link callback to hide it from the instances that do not use this.
> > >Also, clearing of the pending interrupts on init is required due to
> > >observed issues on some platforms.
> > >
> > >Signed-off-by: Jon Mason <jon.mason at broadcom.com>
> > >---
> > > drivers/net/ethernet/broadcom/bgmac-platform.c | 56 +++++++++++++++++++++++++-
> > > drivers/net/ethernet/broadcom/bgmac.c | 3 ++
> > > drivers/net/ethernet/broadcom/bgmac.h | 1 +
> > > 3 files changed, 58 insertions(+), 2 deletions(-)
> > >
> > >diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
> > >index aed5dc5..f6d48c7 100644
> > >--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
> > >+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
> > >@@ -14,12 +14,21 @@
> > > #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> > >
> > > #include <linux/bcma/bcma.h>
> > >+#include <linux/brcmphy.h>
> > > #include <linux/etherdevice.h>
> > > #include <linux/of_address.h>
> > > #include <linux/of_mdio.h>
> > > #include <linux/of_net.h>
> > > #include "bgmac.h"
> > >
> > >+#define NICPM_IOMUX_CTRL 0x00000008
> > >+
> > >+#define NICPM_IOMUX_CTRL_INIT_VAL 0x3196e000
> > >+#define NICPM_IOMUX_CTRL_SPD_SHIFT 10
> > >+#define NICPM_IOMUX_CTRL_SPD_10M 0
> > >+#define NICPM_IOMUX_CTRL_SPD_100M 1
> > >+#define NICPM_IOMUX_CTRL_SPD_1000M 2
> > >+
> > > static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
> > > {
> > > return readl(bgmac->plat.base + offset);
> > >@@ -87,12 +96,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
> > > WARN_ON(1);
> > > }
> > >
> > >+static void bgmac_nicpm_speed_set(struct net_device *net_dev)
> > >+{
> > >+ struct bgmac *bgmac = netdev_priv(net_dev);
> > >+ u32 val;
> > >+
> > >+ if (!bgmac->plat.nicpm_base)
> > >+ return;
> > >+
> > >+ val = NICPM_IOMUX_CTRL_INIT_VAL;
> > >+ switch (bgmac->net_dev->phydev->speed) {
> > >+ default:
> > >+ pr_err("Unsupported speed. Defaulting to 1000Mb\n");
> > This should be dev_err
>
> It should probably be netdev_err (and there are a few instances below
> that should probably be changed to netdev_err as well).
Actually, the other instances I referenced above should not be
netdev_err, as they are enountered before the netdev is created. So,
dev_err is correct for them.
That being said, the original pr_err that Scott referenced should be
netdev_err (as it is encountered after the netdev is created). v5 will
make that change.
Thanks,
Jon
>
> Thanks,
> Jon
>
> > >+ case SPEED_1000:
> > >+ val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> > >+ break;
> > >+ case SPEED_100:
> > >+ val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> > >+ break;
> > >+ case SPEED_10:
> > >+ val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
> > >+ break;
> > >+ }
> > >+
> > >+ writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
> > >+
> > >+ bgmac_adjust_link(bgmac->net_dev);
> > >+}
> > >+
> > > static int platform_phy_connect(struct bgmac *bgmac)
> > > {
> > > struct phy_device *phy_dev;
> > >
> > >- phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
> > >- bgmac_adjust_link);
> > >+ if (bgmac->plat.nicpm_base)
> > >+ phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> > >+ bgmac->dev->of_node,
> > >+ bgmac_nicpm_speed_set);
> > >+ else
> > >+ phy_dev = of_phy_get_and_connect(bgmac->net_dev,
> > >+ bgmac->dev->of_node,
> > >+ bgmac_adjust_link);
> > > if (!phy_dev) {
> > > dev_err(bgmac->dev, "Phy connect failed\n");
> > > return -ENODEV;
> > >@@ -182,6 +225,14 @@ static int bgmac_probe(struct platform_device *pdev)
> > > if (IS_ERR(bgmac->plat.idm_base))
> > > return PTR_ERR(bgmac->plat.idm_base);
> > >
> > >+ regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
> > >+ if (regs) {
> > >+ bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
> > >+ regs);
> > >+ if (IS_ERR(bgmac->plat.nicpm_base))
> > >+ return PTR_ERR(bgmac->plat.nicpm_base);
> > >+ }
> > >+
> > > bgmac->read = platform_bgmac_read;
> > > bgmac->write = platform_bgmac_write;
> > > bgmac->idm_read = platform_bgmac_idm_read;
> > >@@ -213,6 +264,7 @@ static int bgmac_remove(struct platform_device *pdev)
> > > static const struct of_device_id bgmac_of_enet_match[] = {
> > > {.compatible = "brcm,amac",},
> > > {.compatible = "brcm,nsp-amac",},
> > >+ {.compatible = "brcm,ns2-amac",},
> > > {},
> > > };
> > >
> > >diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
> > >index 4584958..a805cc8 100644
> > >--- a/drivers/net/ethernet/broadcom/bgmac.c
> > >+++ b/drivers/net/ethernet/broadcom/bgmac.c
> > >@@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
> > > /* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
> > > static void bgmac_chip_init(struct bgmac *bgmac)
> > > {
> > >+ /* Clear any erroneously pending interrupts */
> > >+ bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
> > >+
> > > /* 1 interrupt per received frame */
> > > bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
> > >
> > >diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
> > >index ea52ac3..b1820ea 100644
> > >--- a/drivers/net/ethernet/broadcom/bgmac.h
> > >+++ b/drivers/net/ethernet/broadcom/bgmac.h
> > >@@ -463,6 +463,7 @@ struct bgmac {
> > > struct {
> > > void *base;
> > > void *idm_base;
> > >+ void *nicpm_base;
> > > } plat;
> > > struct {
> > > struct bcma_device *core;
> > >
More information about the linux-arm-kernel
mailing list