[PATCH v4 1/2] ARM: dts: imx6: Add support for Toradex Apalis iMX6Q/D SoM
Shawn Guo
shawnguo at kernel.org
Mon Feb 1 05:29:16 PST 2016
On Sun, Jan 24, 2016 at 11:48:22PM +0100, Marcel Ziswiler wrote:
> From: Petr Štetiar <ynezz at true.cz>
>
> Signed-off-by: Marcel Ziswiler <marcel.ziswiler at toradex.com>
> Signed-off-by: Petr Štetiar <ynezz at true.cz>
> Reviewed-by: Stefan Agner <stefan at agner.ch>
> ---
>
> Changes in v4:
> - integrated review feedback from Fabio
>
> Changes in v3:
> - integrated review feedback from Petr
> - integrated review feedback from Stefan
> - move I2C DDC enablement and assignement handling into carrier board DTS where it belongs
> - move CAN nodes up a little to keep the alphabetical order
> - added an explanatory comment about PWR_I2C usage
>
> Changes in v2:
> - clarify exact Apalis iMX6Q/D SoM type in cover letter
> - clarify exact Apalis iMX6Q/D module type and Ixora carrier board in model
> node
> - got rid of obsolete mmc aliases
> - working SGTL5000 audio/sound integration
> - working STMPE811 touch screen controller integration
> - integrated review feedback from Lucas
> - left and even added some more comments as I don't see why putting any
> explanatory comments in dts' should be such a bad thing to do
> - completely got rid of the memory node as that is something typically filled
> in by the boot loader e.g. U-Boot
> - without the regulators simple-bus it no longer boots
> - even though we supposedly shipped a few hundred V1.0a modules drop DCE UART
> support for now and simplify file layout
> - replaced obsolete no-1-8-v by mainline supported voltage-ranges = <3300 3300>
> usdhc property and yes card detects are indeed active low (;-p)
> - integrated review feedback from Stefan
> - fixed Ethernet PHY reset & interrupt (requires Micrel PHY driver to be
> enabled)
> - fixed HDMI DDC (requires GPIO-based bitbanging I2C to be enabled)
> - fixed SPDIF
>
> arch/arm/boot/dts/imx6qdl-apalis.dtsi | 1011 +++++++++++++++++++++++++++++++++
> 1 file changed, 1011 insertions(+)
> create mode 100644 arch/arm/boot/dts/imx6qdl-apalis.dtsi
>
> diff --git a/arch/arm/boot/dts/imx6qdl-apalis.dtsi b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
> new file mode 100644
> index 0000000..5306466
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-apalis.dtsi
> @@ -0,0 +1,1011 @@
> +/*
> + * Copyright 2014-2016 Toradex AG
> + * Copyright 2012 Freescale Semiconductor, Inc.
> + * Copyright 2011 Linaro Ltd.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License
> + * version 2 as published by the Free Software Foundation.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> + model = "Toradex Apalis iMX6Q/D Module";
> + compatible = "toradex,apalis_imx6q", "fsl,imx6q";
> +
> + backlight: backlight {
> + compatible = "pwm-backlight";
> + pwms = <&pwm4 0 5000000>;
> + status = "disabled";
> + };
> +
> + /* DDC_I2C: I2C2_SDA/SCL on MXM3 205/207 */
> + i2cddc: i2c at 0 {
> + compatible = "i2c-gpio";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c_ddc>;
> + gpios = <&gpio3 16 GPIO_ACTIVE_HIGH /* sda */
> + &gpio2 30 GPIO_ACTIVE_HIGH /* scl */
> + >;
> + i2c-gpio,delay-us = <2>; /* ~100 kHz */
> + status = "disabled";
> + };
> +
> + regulators {
> + compatible = "simple-bus";
> +
> + reg_1p8v: 1p8v {
> + compatible = "regulator-fixed";
> + regulator-name = "1P8V";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
As Petr already mentioned, we should try to put these fixed regulators
directly under root node. In that case, we can drop the fake
simple-bus container node and save the artificial 'reg' property. The
regulators can be named in the following schema:
reg_xxx: regulator-xxx {
...
}
> +
> + reg_2p5v: 2p5v {
> + compatible = "regulator-fixed";
> + regulator-name = "2P5V";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + regulator-always-on;
> + };
> +
> + reg_3p3v: 3p3v {
> + compatible = "regulator-fixed";
> + regulator-name = "3P3V";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + reg_usb_otg_vbus: usb_otg_vbus {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_regulator_usbotg_pwr>;
> + regulator-name = "usb_otg_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio3 22 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + status = "disabled";
> + };
> +
> + /* on module usb hub */
> + reg_usb_host_vbus_hub: usb_host_vbus_hub {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_regulator_usbhub_pwr>;
> + regulator-name = "usb_host_vbus_hub";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio3 28 GPIO_ACTIVE_HIGH>;
> + startup-delay-us = <2000>;
> + enable-active-high;
> + status = "okay";
> + };
> +
> + reg_usb_host_vbus: usb_host_vbus {
> + compatible = "regulator-fixed";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_regulator_usbh_pwr>;
> + regulator-name = "usb_host_vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + vin-supply = <®_usb_host_vbus_hub>;
> + status = "disabled";
> + };
> + };
> +
> + sound {
> + compatible = "fsl,imx-audio-sgtl5000";
> + model = "imx6q-apalis-sgtl5000";
> + ssi-controller = <&ssi1>;
> + audio-codec = <&codec>;
> + audio-routing =
> + "LINE_IN", "Line In Jack",
> + "MIC_IN", "Mic Jack",
> + "Mic Jack", "Mic Bias",
> + "Headphone Jack", "HP_OUT";
> + mux-int-port = <1>;
> + mux-ext-port = <4>;
> + };
> +
> + sound_spdif: sound-spdif {
> + compatible = "fsl,imx-audio-spdif";
> + model = "imx-spdif";
> + spdif-controller = <&spdif>;
> + spdif-in;
> + spdif-out;
> + status = "disabled";
> + };
> +};
> +
> +&audmux {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_audmux &pinctrl_audmux_mclk>;
> + status = "okay";
> +};
> +
> +&can1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan1>;
> + status = "disabled";
> +};
> +
> +&can2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_flexcan2>;
> + status = "disabled";
> +};
> +
> +/* Apalis SPI1 */
> +&ecspi1 {
> + fsl,spi-num-chipselects = <1>;
> + cs-gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_spi_cs1>;
> + status = "disabled";
> +};
> +
> +/* Apalis SPI2 */
> +&ecspi2 {
> + fsl,spi-num-chipselects = <1>;
> + cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ecspi2 &pinctrl_spi_cs2>;
> + status = "disabled";
> +};
> +
> +&fec {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_enet &pinctrl_enet_ctrl>;
> + phy-mode = "rgmii";
> + phy-handle = <ðphy>;
> + phy-reset-duration = <10>;
> + phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + ethphy: ethernet-phy at 7 {
> + interrupt-parent = <&gpio1>;
> + interrupts = <30 IRQ_TYPE_LEVEL_LOW>;
> + reg = <7>;
> + };
> + };
> +};
> +
> +&hdmi {
> + status = "disabled";
> +};
The device is disabled by default in imx6qdl.dtsi, so this is not
needed.
> +
> +/*
> + * GEN1_I2C: I2C1_SDA/SCL on MXM3 209/211 (e.g. RTC on carrier
> + * board)
> + */
> +&i2c1 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + status = "disabled";
> +};
> +
> +/*
> + * PWR_I2C: power I2C to audio codec, PMIC, temperature sensor and
> + * touch screen controller
> + */
> +&i2c2 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c2>;
> + status = "okay";
> +
> + pmic: pfuze100 at 08 {
> + compatible = "fsl,pfuze100";
> + reg = <0x08>;
> +
> + regulators {
> + sw1a_reg: sw1ab {
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw1c_reg: sw1c {
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1875000>;
> + regulator-boot-on;
> + regulator-always-on;
> + regulator-ramp-delay = <6250>;
> + };
> +
> + sw3a_reg: sw3a {
> + regulator-min-microvolt = <400000>;
> + regulator-max-microvolt = <1975000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + swbst_reg: swbst {
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5150000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + snvs_reg: vsnvs {
> + regulator-min-microvolt = <1000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vref_reg: vrefddr {
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen1_reg: vgen1 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen2_reg: vgen2 {
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1550000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen3_reg: vgen3 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen4_reg: vgen4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen5_reg: vgen5 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + vgen6_reg: vgen6 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> + };
> + };
> +
> + codec: sgtl5000 at 0a {
> + compatible = "fsl,sgtl5000";
> + reg = <0x0a>;
> + clocks = <&clks 201>;
> + VDDA-supply = <®_2p5v>;
> + VDDIO-supply = <®_3p3v>;
> + };
> +
> + /* STMPE811 touch screen controller */
> + stmpe811 at 41 {
> + compatible = "st,stmpe811";
The compatible seems to be used by kernel without a binding document.
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_touch_int>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + reg = <0x41>;
> + interrupts = <10 IRQ_TYPE_LEVEL_LOW>;
> + interrupt-parent = <&gpio4>;
> + interrupt-controller;
> + id = <0>;
> + blocks = <0x5>;
> + irq-trigger = <0x1>;
Have a new line between properties and sub-node.
> + stmpe_touchscreen {
Shouldn't the node name be generic as just touchscreen? Or at least,
hyphen instead of underscore should be used in node name.
> + compatible = "st,stmpe-ts";
> + reg = <0>;
> + /* 3.25 MHz ADC clock speed */
> + st,adc-freq = <1>;
> + /* 8 sample average control */
> + st,ave-ctrl = <3>;
> + /* 7 length fractional part in z */
> + st,fraction-z = <7>;
> + /*
> + * 50 mA typical 80 mA max touchscreen drivers
> + * current limit value
> + */
> + st,i-drive = <1>;
> + /* 12-bit ADC */
> + st,mod-12b = <1>;
> + /* internal ADC reference */
> + st,ref-sel = <0>;
> + /* ADC converstion time: 80 clocks */
> + st,sample-time = <4>;
> + /* 1 ms panel driver settling time */
> + st,settling = <3>;
> + /* 5 ms touch detect interrupt delay */
> + st,touch-det-delay = <5>;
> + };
> + };
> +};
> +
> +/*
> + * GEN2_I2C, CAM: I2C3_SDA/SCL on MXM3 201/203 (unused)
> + */
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "recovery";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + pinctrl-1 = <&pinctrl_i2c3_recovery>;
> + scl-gpios = <&gpio3 17 GPIO_ACTIVE_HIGH>;
> + sda-gpios = <&gpio3 18 GPIO_ACTIVE_HIGH>;
> + status = "disabled";
> +};
> +
> +&pwm1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm1>;
> + status = "disabled";
> +};
> +
> +&pwm2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm2>;
> + status = "disabled";
> +};
> +
> +&pwm3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm3>;
> + status = "disabled";
> +};
> +
> +&pwm4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm4>;
> + status = "disabled";
> +};
> +
> +&spdif {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_spdif>;
> + status = "disabled";
> +};
> +
> +&ssi1 {
> + status = "okay";
> +};
> +
> +&uart1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart1_dte &pinctrl_uart1_ctrl>;
> + fsl,dte-mode;
> + fsl,uart-has-rtscts;
> + status = "disabled";
> +};
> +
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2_dte>;
> + fsl,dte-mode;
> + fsl,uart-has-rtscts;
> + status = "disabled";
> +};
> +
> +&uart4 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart4_dte>;
> + fsl,dte-mode;
> + status = "disabled";
> +};
> +
> +&uart5 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart5_dte>;
> + fsl,dte-mode;
> + status = "disabled";
> +};
> +
> +&usbh1 {
> + status = "disabled";
> +};
This is not needed.
> +
> +&usbotg {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usbotg>;
> + disable-over-current;
> + status = "disabled";
> +};
> +
> +/* MMC1 */
> +&usdhc1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + vmmc-supply = <®_3p3v>;
> + bus-width = <8>;
> + voltage-ranges = <3300 3300>;
> + status = "disabled";
> +};
> +
> +/* SD1 */
> +&usdhc2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + vmmc-supply = <®_3p3v>;
> + bus-width = <4>;
> + voltage-ranges = <3300 3300>;
> + status = "disabled";
> +};
> +
> +/* eMMC */
> +&usdhc3 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_usdhc3>;
> + vmmc-supply = <®_3p3v>;
> + bus-width = <8>;
> + voltage-ranges = <3300 3300>;
> + non-removable;
> + status = "okay";
> +};
> +
> +&weim {
> + status = "disabled";
> +};
> +
> +&iomuxc {
> + ecspi {
These function container nodes do not make too much sense now, and can
be dropped, since commit 5fcdf6a7ed95 (pinctrl: imx: Allow parsing DT
without function nodes).
> + pinctrl_ecspi1: ecspi1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT6__ECSPI1_MISO 0x100b1
> + MX6QDL_PAD_CSI0_DAT5__ECSPI1_MOSI 0x100b1
> + MX6QDL_PAD_CSI0_DAT4__ECSPI1_SCLK 0x100b1
> + >;
> + };
Please have a new line between nodes.
> + pinctrl_ecspi2: ecspi2grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
> + MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
> + MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
> + >;
> + };
> + pinctrl_spi_cs1: spi_cs1 {
I would like to see a consistent pinctrl group node naming schema, i.e.
xxxgrp. In any case, underscore shouldn't be used in node name.
> + fsl,pins = <
> + /* SPI1 cs */
> + MX6QDL_PAD_CSI0_DAT7__GPIO5_IO25 0x000b1
> + >;
> + };
I actually think one pinctrl node like the following is good enough,
with some necessary comments on the extra pins.
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX6QDL_PAD_CSI0_DAT6__ECSPI1_MISO 0x100b1
MX6QDL_PAD_CSI0_DAT5__ECSPI1_MOSI 0x100b1
MX6QDL_PAD_CSI0_DAT4__ECSPI1_SCLK 0x100b1
/* SPI1 cs */
MX6QDL_PAD_CSI0_DAT7__GPIO5_IO25 0x000b1
>;
};
If you consider this for all the following pinctrl nodes, I think the
iomuxc node will become a bit clean and clear.
Shawn
> + pinctrl_spi_cs2: spi_cs2 {
> + fsl,pins = <
> + /* SPI2 cs */
> + MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x000b1
> + >;
> + };
> + };
> +
> + flexcan {
> + pinctrl_flexcan1: flexcan1grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x1b0b0
> + MX6QDL_PAD_GPIO_8__FLEXCAN1_RX 0x1b0b0
> + >;
> + };
> + pinctrl_flexcan2: flexcan2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x1b0b0
> + MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x1b0b0
> + >;
> + };
> + };
> +
> + gpio {
> + pinctrl_apalis_gpio1: apalis_gpio1 {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x130b0
> + >;
> + };
> + pinctrl_apalis_gpio2: apalis_gpio2 {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x130b0
> + >;
> + };
> + pinctrl_apalis_gpio3: apalis_gpio3 {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x130b0
> + >;
> + };
> + pinctrl_apalis_gpio4: apalis_gpio4 {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x130b0
> + >;
> + };
> + pinctrl_apalis_gpio5: apalis_gpio5 {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_RB0__GPIO6_IO10 0x130b0
> + >;
> + };
> + pinctrl_apalis_gpio6: apalis_gpio6 {
> + fsl,pins = <
> + MX6QDL_PAD_NANDF_WP_B__GPIO6_IO09 0x130b0
> + >;
> + };
> + pinctrl_apalis_gpio7: apalis_gpio7 {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x130b0
> + >;
> + };
> + pinctrl_apalis_gpio8: apalis_gpio8 {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x130b0
> + >;
> + };
> + pinctrl_gpio_keys: gpio_keys {
> + fsl,pins = <
> + /* Power button */
> + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x1b0b0
> + >;
> + };
> + };
> +
> + hdmi {
> + pinctrl_hdmi_cec: hdmicecgrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0
> + >;
> + };
> + };
> +
> + i2c {
> + pinctrl_i2c_ddc: i2c_ddc {
> + fsl,pins = <
> + /* DDC bitbang */
> + MX6QDL_PAD_EIM_EB2__GPIO2_IO30 0x1b0b0
> + MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x1b0b0
> + >;
> + };
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
> + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
> + >;
> + };
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1
> + MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1
> + >;
> + };
> + pinctrl_i2c3_recovery: i2c3-recoverygrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D17__GPIO3_IO17 0x4001b8b1
> + MX6QDL_PAD_EIM_D18__GPIO3_IO18 0x4001b8b1
> + >;
> + };
> + };
> +
> + /* pins used on module */
> + imx6q-apalis {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_reset_moci &pinctrl_emmc_reset>;
> + pinctrl_audmux: audmuxgrp {
> + fsl,pins = <
> + MX6QDL_PAD_DISP0_DAT20__AUD4_TXC 0x130b0
> + MX6QDL_PAD_DISP0_DAT21__AUD4_TXD 0x130b0
> + MX6QDL_PAD_DISP0_DAT22__AUD4_TXFS 0x130b0
> + MX6QDL_PAD_DISP0_DAT23__AUD4_RXD 0x130b0
> + >;
> + };
> + pinctrl_audmux_mclk: audmux_mclk {
> + fsl,pins = <
> + /* SGTL5000 sys_mclk */
> + MX6QDL_PAD_GPIO_5__CCM_CLKO1 0x130b0
> + >;
> + };
> + pinctrl_emmc_reset: emmc_reset {
> + fsl,pins = <
> + /* eMMC reset, leave it alone */
> + MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x0f058
> + >;
> + };
> + pinctrl_enet: enetgrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0
> + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0
> + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0
> + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0
> + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0
> + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0
> + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0
> + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0
> + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0
> + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
> + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
> + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
> + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
> + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
> + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
> + >;
> + };
> + pinctrl_enet_ctrl: enet_ctrlgrp {
> + fsl,pins = <
> + /* Ethernet PHY reset */
> + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x000b0
> + /* Ethernet PHY interrupt */
> + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x000b1
> + >;
> + };
> + pinctrl_i2c2: i2c2grp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
> + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
> + >;
> + };
> + pinctrl_ipu2_vdac: ipu2vdacgrp {
> + fsl,pins = <
> + MX6QDL_PAD_DI0_DISP_CLK__IPU2_DI0_DISP_CLK 0xd1
> + MX6QDL_PAD_DI0_PIN15__IPU2_DI0_PIN15 0xd1
> + MX6QDL_PAD_DI0_PIN2__IPU2_DI0_PIN02 0xd1
> + MX6QDL_PAD_DI0_PIN3__IPU2_DI0_PIN03 0xd1
> + MX6QDL_PAD_DISP0_DAT0__IPU2_DISP0_DATA00 0xf9
> + MX6QDL_PAD_DISP0_DAT1__IPU2_DISP0_DATA01 0xf9
> + MX6QDL_PAD_DISP0_DAT2__IPU2_DISP0_DATA02 0xf9
> + MX6QDL_PAD_DISP0_DAT3__IPU2_DISP0_DATA03 0xf9
> + MX6QDL_PAD_DISP0_DAT4__IPU2_DISP0_DATA04 0xf9
> + MX6QDL_PAD_DISP0_DAT5__IPU2_DISP0_DATA05 0xf9
> + MX6QDL_PAD_DISP0_DAT6__IPU2_DISP0_DATA06 0xf9
> + MX6QDL_PAD_DISP0_DAT7__IPU2_DISP0_DATA07 0xf9
> + MX6QDL_PAD_DISP0_DAT8__IPU2_DISP0_DATA08 0xf9
> + MX6QDL_PAD_DISP0_DAT9__IPU2_DISP0_DATA09 0xf9
> + MX6QDL_PAD_DISP0_DAT10__IPU2_DISP0_DATA10 0xf9
> + MX6QDL_PAD_DISP0_DAT11__IPU2_DISP0_DATA11 0xf9
> + MX6QDL_PAD_DISP0_DAT12__IPU2_DISP0_DATA12 0xf9
> + MX6QDL_PAD_DISP0_DAT13__IPU2_DISP0_DATA13 0xf9
> + MX6QDL_PAD_DISP0_DAT14__IPU2_DISP0_DATA14 0xf9
> + MX6QDL_PAD_DISP0_DAT15__IPU2_DISP0_DATA15 0xf9
> + >;
> + };
> + pinctrl_regulator_usbhub_pwr: gpio_regulator_usbhub_pwr {
> + fsl,pins = <
> + /* USBH_HUB_EN */
> + MX6QDL_PAD_EIM_D28__GPIO3_IO28 0x0f058
> + >;
> + };
> + pinctrl_reset_moci: gpio_reset_moci {
> + fsl,pins = <
> + /* RESET_MOCI control */
> + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x0f058
> + >;
> + };
> + pinctrl_touch_int: touch_intgrp {
> + fsl,pins = <
> + /* STMPE811 interrupt */
> + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x1b0b0
> + >;
> + };
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059
> + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059
> + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059
> + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059
> + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059
> + >;
> + };
> + pinctrl_usdhc3_100mhz: usdhc3grp-100mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9
> + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170b9
> + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170b9
> + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170b9
> + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170b9
> + >;
> + };
> + pinctrl_usdhc3_200mhz: usdhc3grp-200mhz {
> + fsl,pins = <
> + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9
> + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9
> + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9
> + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9
> + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9
> + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9
> + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170f9
> + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170f9
> + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170f9
> + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170f9
> + >;
> + };
> + };
> +
> + ipu1 {
> + pinctrl_ipu1_lcdif: ipu1lcdifgrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_A16__IPU1_DI1_DISP_CLK 0x61
> + /* DE */
> + MX6QDL_PAD_EIM_DA10__IPU1_DI1_PIN15 0x61
> + /* HSync */
> + MX6QDL_PAD_EIM_DA11__IPU1_DI1_PIN02 0x61
> + /* VSync */
> + MX6QDL_PAD_EIM_DA12__IPU1_DI1_PIN03 0x61
> + MX6QDL_PAD_EIM_DA9__IPU1_DISP1_DATA00 0x61
> + MX6QDL_PAD_EIM_DA8__IPU1_DISP1_DATA01 0x61
> + MX6QDL_PAD_EIM_DA7__IPU1_DISP1_DATA02 0x61
> + MX6QDL_PAD_EIM_DA6__IPU1_DISP1_DATA03 0x61
> + MX6QDL_PAD_EIM_DA5__IPU1_DISP1_DATA04 0x61
> + MX6QDL_PAD_EIM_DA4__IPU1_DISP1_DATA05 0x61
> + MX6QDL_PAD_EIM_DA3__IPU1_DISP1_DATA06 0x61
> + MX6QDL_PAD_EIM_DA2__IPU1_DISP1_DATA07 0x61
> + MX6QDL_PAD_EIM_DA1__IPU1_DISP1_DATA08 0x61
> + MX6QDL_PAD_EIM_DA0__IPU1_DISP1_DATA09 0x61
> + MX6QDL_PAD_EIM_EB1__IPU1_DISP1_DATA10 0x61
> + MX6QDL_PAD_EIM_EB0__IPU1_DISP1_DATA11 0x61
> + MX6QDL_PAD_EIM_A17__IPU1_DISP1_DATA12 0x61
> + MX6QDL_PAD_EIM_A18__IPU1_DISP1_DATA13 0x61
> + MX6QDL_PAD_EIM_A19__IPU1_DISP1_DATA14 0x61
> + MX6QDL_PAD_EIM_A20__IPU1_DISP1_DATA15 0x61
> + MX6QDL_PAD_EIM_A21__IPU1_DISP1_DATA16 0x61
> + MX6QDL_PAD_EIM_A22__IPU1_DISP1_DATA17 0x61
> + MX6QDL_PAD_EIM_A23__IPU1_DISP1_DATA18 0x61
> + MX6QDL_PAD_EIM_A24__IPU1_DISP1_DATA19 0x61
> + MX6QDL_PAD_EIM_D31__IPU1_DISP1_DATA20 0x61
> + MX6QDL_PAD_EIM_D30__IPU1_DISP1_DATA21 0x61
> + MX6QDL_PAD_EIM_D26__IPU1_DISP1_DATA22 0x61
> + MX6QDL_PAD_EIM_D27__IPU1_DISP1_DATA23 0x61
> + >;
> + };
> + pinctrl_cam_mclk: cam_mclk {
> + fsl,pins = <
> + /* CAM sys_mclk */
> + MX6QDL_PAD_NANDF_CS2__CCM_CLKO2 0x00b0
> + >;
> + };
> + pinctrl_ipu1_csi0: ipu1csi0grp { /* parallel camera */
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0xb0b1
> + MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0xb0b1
> + MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0xb0b1
> + MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0xb0b1
> + MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0xb0b1
> + MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0xb0b1
> + MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0xb0b1
> + MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0xb0b1
> + MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0xb0b1
> + MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0xb0b1
> + MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0xb0b1
> + >;
> + };
> + };
> +
> + pwm {
> + pinctrl_pwm1: pwm1grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b1
> + >;
> + };
> + pinctrl_pwm2: pwm2grp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_1__PWM2_OUT 0x1b0b1
> + >;
> + };
> + pinctrl_pwm3: pwm3grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1
> + >;
> + };
> + pinctrl_pwm4: pwm4grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_DAT2__PWM4_OUT 0x1b0b1
> + >;
> + };
> + };
> +
> + spdif {
> + pinctrl_spdif: spdifgrp {
> + fsl,pins = <
> + MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0
> + MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0
> + >;
> + };
> + };
> +
> + uart1 {
> + pinctrl_uart1_dce: uart1-dcegrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + /* DTE mode */
> + pinctrl_uart1_dte: uart1-dtegrp {
> + fsl,pins = <
> + MX6QDL_PAD_CSI0_DAT10__UART1_RX_DATA 0x1b0b1
> + MX6QDL_PAD_CSI0_DAT11__UART1_TX_DATA 0x1b0b1
> + MX6QDL_PAD_EIM_D19__UART1_RTS_B 0x1b0b1
> + MX6QDL_PAD_EIM_D20__UART1_CTS_B 0x1b0b1
> + >;
> + };
> +
> + /* Additional DTR, DSR, DCD */
> + pinctrl_uart1_ctrl: uart1-ctrlgrp {
> + fsl,pins = <
> + MX6QDL_PAD_EIM_D23__UART1_DCD_B 0x1b0b0
> + MX6QDL_PAD_EIM_D24__UART1_DTR_B 0x1b0b0
> + MX6QDL_PAD_EIM_D25__UART1_DSR_B 0x1b0b0
> + >;
> + };
> + };
> +
> + uart2 {
> + pinctrl_uart2_dce: uart2-dcegrp {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1
> + MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1
> + >;
> + };
> +
> + /* DTE mode */
> + pinctrl_uart2_dte: uart2grp-dte {
> + fsl,pins = <
> + MX6QDL_PAD_SD4_DAT4__UART2_TX_DATA 0x1b0b1
> + MX6QDL_PAD_SD4_DAT7__UART2_RX_DATA 0x1b0b1
> + MX6QDL_PAD_SD4_DAT6__UART2_RTS_B 0x1b0b1
> + MX6QDL_PAD_SD4_DAT5__UART2_CTS_B 0x1b0b1
> + >;
> + };
> + };
> +
> + uart4 {
> + pinctrl_uart4_dce: uart4-dcegrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + /* DTE mode */
> + pinctrl_uart4_dte: uart4-dtegrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL0__UART4_RX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW0__UART4_TX_DATA 0x1b0b1
> + >;
> + };
> + };
> +
> + uart5 {
> + pinctrl_uart5_dce: uart5-dcegrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1
> + >;
> + };
> +
> + /* DTE mode */
> + pinctrl_uart5_dte: uart5-dtegrp {
> + fsl,pins = <
> + MX6QDL_PAD_KEY_COL1__UART5_RX_DATA 0x1b0b1
> + MX6QDL_PAD_KEY_ROW1__UART5_TX_DATA 0x1b0b1
> + >;
> + };
> + };
> +
> + usbh {
> + pinctrl_regulator_usbh_pwr: gpio_regulator_usbh_pwr {
> + fsl,pins = <
> + /* USBH_EN */
> + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x0f058
> + >;
> + };
> + };
> +
> + usbotg {
> + pinctrl_usbotg: usbotggrp {
> + fsl,pins = <
> + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059
> + >;
> + };
> + pinctrl_regulator_usbotg_pwr: gpio_regulator_usbotg_pwr {
> + fsl,pins = <
> + /* USBO1 power en */
> + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x0f058
> + >;
> + };
> + };
> +
> + usdhc {
> + pinctrl_mmc_cd: gpio_mmc_cd {
> + fsl,pins = <
> + /* MMC1 CD */
> + MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x000b0
> + >;
> + };
> + pinctrl_sd_cd: gpio_sd_cd {
> + fsl,pins = <
> + /* SD1 CD */
> + MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x000b0
> + >;
> + };
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17071
> + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10071
> + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17071
> + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17071
> + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17071
> + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17071
> + MX6QDL_PAD_NANDF_D0__SD1_DATA4 0x17071
> + MX6QDL_PAD_NANDF_D1__SD1_DATA5 0x17071
> + MX6QDL_PAD_NANDF_D2__SD1_DATA6 0x17071
> + MX6QDL_PAD_NANDF_D3__SD1_DATA7 0x17071
> + >;
> + };
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17071
> + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10071
> + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17071
> + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17071
> + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17071
> + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17071
> + >;
> + };
> + };
> +};
> --
> 2.5.0
>
>
More information about the linux-arm-kernel
mailing list