[PATCH v5] ARM: dts: imx: add Boundary Devices Nitrogen6_SoloX board

Gary Bisson gary.bisson at boundarydevices.com
Mon Apr 11 14:01:36 PDT 2016


Based on i.MX6 SoloX with 1GB of RAM.

https://boundarydevices.com/product/nit6_solox-imx6/

Signed-off-by: Gary Bisson <gary.bisson at boundarydevices.com>
---

Changes v1 -> v2:
- Remove lines commented out from nitrogen6sx dts as suggested by Vladimir
Changes v2 -> v3:
- none
Changes v3 -> v4:
- Use hyphen instead of underscore for backlight node name
- Remove fake "simple-bus" for regulators declaration
- Remove non existant vqmmc-1-8v property
- Remove unused pinctrl entries (rfkill, lvds)
- Remove pinctrl unnecessary container node
Changes v4 -> v5:
- Remove non existant vqmmc-1-8v for real
- Add new line between properties and sub-nodes
- Use lowercase for all hexadecimal values
- Remove unnecessary fsl,mode of ssi node
- Remove deprecated keep-power-in-suspend

Thanks for all your feedback!

Regards,
Gary

---
 arch/arm/boot/dts/Makefile               |   1 +
 arch/arm/boot/dts/imx6sx-nitrogen6sx.dts | 709 +++++++++++++++++++++++++++++++
 2 files changed, 710 insertions(+)
 create mode 100644 arch/arm/boot/dts/imx6sx-nitrogen6sx.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 54306aa..9eab5f5 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -371,6 +371,7 @@ dtb-$(CONFIG_SOC_IMX6SL) += \
 	imx6sl-evk.dtb \
 	imx6sl-warp.dtb
 dtb-$(CONFIG_SOC_IMX6SX) += \
+	imx6sx-nitrogen6sx.dtb \
 	imx6sx-sabreauto.dtb \
 	imx6sx-sdb-reva.dtb \
 	imx6sx-sdb.dtb
diff --git a/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts b/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts
new file mode 100644
index 0000000..ba62348
--- /dev/null
+++ b/arch/arm/boot/dts/imx6sx-nitrogen6sx.dts
@@ -0,0 +1,709 @@
+/*
+ * Copyright (C) 2016 Boundary Devices, Inc.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+
+#include "imx6sx.dtsi"
+
+/ {
+	model = "Boundary Devices i.MX6 SoloX Nitrogen6sx Board";
+	compatible = "boundary,imx6sx-nitrogen6sx", "fsl,imx6sx";
+
+	aliases {
+		fb_lcd = &lcdif1;
+		t_lcd = &t_lcd;
+	};
+
+	memory {
+		reg = <0x80000000 0x40000000>;
+	};
+
+	backlight-lvds {
+		compatible = "pwm-backlight";
+		pwms = <&pwm4 0 5000000>;
+		brightness-levels = <0 4 8 16 32 64 128 255>;
+		default-brightness-level = <6>;
+		power-supply = <&reg_3p3v>;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	reg_can1_3v3: regulator-can1-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "can1-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 27 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_can2_3v3: regulator-can2-3v3 {
+		compatible = "regulator-fixed";
+		regulator-name = "can2-3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&gpio4 24 GPIO_ACTIVE_LOW>;
+	};
+
+	reg_usb_otg1_vbus: regulator-usb-otg1-vbus {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_usbotg1_vbus>;
+		compatible = "regulator-fixed";
+		regulator-name = "usb_otg1_vbus";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		gpio = <&gpio1 9 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	reg_wlan: regulator-wlan {
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_reg_wlan>;
+		compatible = "regulator-fixed";
+		clocks = <&clks IMX6SX_CLK_CKO>;
+		clock-names = "slow";
+		regulator-name = "wlan-en";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		startup-delay-us = <70000>;
+		gpio = <&gpio7 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	sound {
+		compatible = "fsl,imx-audio-sgtl5000";
+		model = "imx6sx-nitrogen6sx-sgtl5000";
+		cpu-dai = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <5>;
+	};
+};
+
+&audmux {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_audmux>;
+	status = "okay";
+};
+
+&ecspi1 {
+	fsl,spi-num-chipselects = <1>;
+	cs-gpios = <&gpio2 16 GPIO_ACTIVE_LOW>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_ecspi1>;
+	status = "okay";
+
+	flash: m25p80 at 0 {
+		compatible = "microchip,sst25vf016b";
+		spi-max-frequency = <20000000>;
+		reg = <0>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+
+		partition at 0 {
+			label = "U-Boot";
+			reg = <0x0 0xc0000>;
+			read-only;
+		};
+
+		partition at c0000 {
+			label = "env";
+			reg = <0xc0000 0x2000>;
+			read-only;
+		};
+
+		partition at c2000 {
+			label = "Kernel";
+			reg = <0xc2000 0x11e000>;
+		};
+
+		partition at 1e0000 {
+			label = "M4";
+			reg = <0x1e0000 0x20000>;
+		};
+	};
+};
+
+&fec1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet1>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_3p3v>;
+	fsl,magic-packet;
+	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		ethphy1: ethernet-phy at 4 {
+			reg = <4>;
+		};
+
+		ethphy2: ethernet-phy at 5 {
+			reg = <5>;
+		};
+	};
+};
+
+&fec2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_enet2>;
+	phy-mode = "rgmii";
+	phy-handle = <&ethphy2>;
+	phy-supply = <&reg_3p3v>;
+	fsl,magic-packet;
+	status = "okay";
+};
+
+&flexcan1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan1>;
+	xceiver-supply = <&reg_can1_3v3>;
+	status = "okay";
+};
+
+&flexcan2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_flexcan2>;
+	xceiver-supply = <&reg_can2_3v3>;
+	status = "okay";
+};
+
+&i2c1 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c1>;
+	status = "okay";
+
+	codec: sgtl5000 at 0a {
+		compatible = "fsl,sgtl5000";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_sgtl5000>;
+		reg = <0x0a>;
+		clocks = <&clks IMX6SX_CLK_CKO2>;
+		VDDA-supply = <&reg_1p8v>;
+		VDDIO-supply = <&reg_1p8v>;
+		VDDD-supply = <&reg_1p8v>;
+		assigned-clocks = <&clks IMX6SX_CLK_CKO2_SEL>,
+				  <&clks IMX6SX_CLK_CKO2>;
+		assigned-clock-parents = <&clks IMX6SX_CLK_OSC>;
+		assigned-clock-rates = <0>, <24000000>;
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+	status = "okay";
+};
+
+&i2c3 {
+	clock-frequency = <100000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c3>;
+	status = "okay";
+};
+
+&lcdif1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_lcdif1>;
+	lcd-supply = <&reg_3p3v>;
+	display = <&display0>;
+	status = "okay";
+
+	display0: display0 {
+		bits-per-pixel = <16>;
+		bus-width = <24>;
+
+		display-timings {
+			native-mode = <&t_lcd>;
+			t_lcd: t_lcd_default {
+				clock-frequency = <74160000>;
+				hactive = <1280>;
+				vactive = <720>;
+				hback-porch = <220>;
+				hfront-porch = <110>;
+				vback-porch = <20>;
+				vfront-porch = <5>;
+				hsync-len = <40>;
+				vsync-len = <5>;
+				hsync-active = <0>;
+				vsync-active = <0>;
+				de-active = <1>;
+				pixelclk-active = <0>;
+			};
+		};
+	};
+};
+
+&pcie {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pcie>;
+	reset-gpio = <&gpio4 10 GPIO_ACTIVE_HIGH>;
+	status = "okay";
+};
+
+&pwm4 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_pwm4>;
+	status = "okay";
+};
+
+&ssi1 {
+	status = "okay";
+};
+
+&uart1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart1>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart2>;
+	status = "okay";
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart3>;
+	fsl,uart-has-rtscts;
+	status = "okay";
+};
+
+&uart5 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_uart5>;
+	status = "okay";
+};
+
+&usbotg1 {
+	vbus-supply = <&reg_usb_otg1_vbus>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg1>;
+	status = "okay";
+};
+
+&usbotg2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usbotg2>;
+	dr_mode = "host";
+	disable-over-current;
+	reset-gpios = <&gpio4 26 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&usdhc2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc2>;
+	bus-width = <4>;
+	cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
+	keep-power-in-suspend;
+	wakeup-source;
+	status = "okay";
+};
+
+&usdhc3 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_usdhc3>;
+	bus-width = <4>;
+	non-removable;
+	keep-power-in-suspend;
+	vmmc-supply = <&reg_wlan>;
+	cap-power-off-card;
+	cap-sdio-irq;
+	status = "okay";
+
+	brcmf: bcrmf at 1 {
+		reg = <1>;
+		compatible = "brcm,bcm4329-fmac";
+		interrupt-parent = <&gpio7>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+	};
+
+	wlcore: wlcore at 2 {
+		compatible = "ti,wl1271";
+		reg = <2>;
+		interrupt-parent = <&gpio7>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+		ref-clock-frequency = <38400000>;
+	};
+};
+
+&usdhc4 {
+	pinctrl-names = "default", "state_100mhz", "state_200mhz";
+	pinctrl-0 = <&pinctrl_usdhc4_50mhz>;
+	pinctrl-1 = <&pinctrl_usdhc4_100mhz>;
+	pinctrl-2 = <&pinctrl_usdhc4_200mhz>;
+	bus-width = <8>;
+	non-removable;
+	vmmc-supply = <&reg_1p8v>;
+	keep-power-in-suspend;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hog>;
+
+	pinctrl_audmux: audmuxgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD1_DATA0__AUDMUX_AUD5_RXD	0x1b0b0
+			MX6SX_PAD_SD1_DATA1__AUDMUX_AUD5_TXC	0x1b0b0
+			MX6SX_PAD_SD1_DATA2__AUDMUX_AUD5_TXFS	0x1b0b0
+			MX6SX_PAD_SD1_DATA3__AUDMUX_AUD5_TXD	0x1b0b0
+		>;
+	};
+
+	pinctrl_ecspi1: ecspi1grp {
+		fsl,pins = <
+			MX6SX_PAD_KEY_COL1__ECSPI1_MISO		0x100b1
+			MX6SX_PAD_KEY_ROW0__ECSPI1_MOSI		0x100b1
+			MX6SX_PAD_KEY_COL0__ECSPI1_SCLK		0x100b1
+			MX6SX_PAD_KEY_ROW1__GPIO2_IO_16		0x0b0b1
+		>;
+	};
+
+	pinctrl_enet1: enet1grp {
+		fsl,pins = <
+			MX6SX_PAD_ENET1_MDIO__ENET1_MDIO	0x1b0b0
+			MX6SX_PAD_ENET1_MDC__ENET1_MDC		0x1b0b0
+			MX6SX_PAD_RGMII1_TD0__ENET1_TX_DATA_0	0x30b1
+			MX6SX_PAD_RGMII1_TD1__ENET1_TX_DATA_1	0x30b1
+			MX6SX_PAD_RGMII1_TD2__ENET1_TX_DATA_2	0x30b1
+			MX6SX_PAD_RGMII1_TD3__ENET1_TX_DATA_3	0x30b1
+			MX6SX_PAD_RGMII1_TXC__ENET1_RGMII_TXC	0x30b1
+			MX6SX_PAD_RGMII1_TX_CTL__ENET1_TX_EN	0x30b1
+			MX6SX_PAD_RGMII1_RD0__ENET1_RX_DATA_0	0x3081
+			MX6SX_PAD_RGMII1_RD1__ENET1_RX_DATA_1	0x3081
+			MX6SX_PAD_RGMII1_RX_CTL__ENET1_RX_EN	0x3081
+			MX6SX_PAD_RGMII1_RD2__ENET1_RX_DATA_2	0x3081
+			MX6SX_PAD_RGMII1_RD3__ENET1_RX_DATA_3	0x3081
+			MX6SX_PAD_RGMII1_RXC__ENET1_RX_CLK	0x3081
+			MX6SX_PAD_ENET2_CRS__GPIO2_IO_7		0xb0b0
+			MX6SX_PAD_ENET1_RX_CLK__GPIO2_IO_4	0xb0b0
+			MX6SX_PAD_ENET1_TX_CLK__GPIO2_IO_5	0xb0b0
+		>;
+	};
+
+	pinctrl_enet2: enet2grp {
+		fsl,pins = <
+			MX6SX_PAD_RGMII2_TD0__ENET2_TX_DATA_0	0x30b1
+			MX6SX_PAD_RGMII2_TD1__ENET2_TX_DATA_1	0x30b1
+			MX6SX_PAD_RGMII2_TD2__ENET2_TX_DATA_2	0x30b1
+			MX6SX_PAD_RGMII2_TD3__ENET2_TX_DATA_3	0x30b1
+			MX6SX_PAD_RGMII2_TXC__ENET2_RGMII_TXC	0x30b1
+			MX6SX_PAD_RGMII2_TX_CTL__ENET2_TX_EN	0x30b1
+			MX6SX_PAD_RGMII2_RD0__ENET2_RX_DATA_0	0x3081
+			MX6SX_PAD_RGMII2_RD1__ENET2_RX_DATA_1	0x3081
+			MX6SX_PAD_RGMII2_RX_CTL__ENET2_RX_EN	0x3081
+			MX6SX_PAD_RGMII2_RD2__ENET2_RX_DATA_2	0x3081
+			MX6SX_PAD_RGMII2_RD3__ENET2_RX_DATA_3	0x3081
+			MX6SX_PAD_RGMII2_RXC__ENET2_RX_CLK	0x3081
+			MX6SX_PAD_ENET2_COL__GPIO2_IO_6		0xb0b0
+			MX6SX_PAD_ENET2_RX_CLK__GPIO2_IO_8	0xb0b0
+			MX6SX_PAD_ENET2_TX_CLK__GPIO2_IO_9	0xb0b0
+		>;
+	};
+
+	pinctrl_flexcan1: flexcan1grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1B_DQS__CAN1_TX		0x1b0b0
+			MX6SX_PAD_QSPI1A_SS1_B__CAN1_RX		0x1b0b0
+			MX6SX_PAD_QSPI1B_DATA3__GPIO4_IO_27	0x1b0b0
+			MX6SX_PAD_QSPI1B_DATA3__GPIO4_IO_27	0x0b0b0
+		>;
+	};
+
+	pinctrl_flexcan2: flexcan2grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1A_DQS__CAN2_TX		0x1b0b0
+			MX6SX_PAD_QSPI1B_SS1_B__CAN2_RX		0x1b0b0
+			MX6SX_PAD_QSPI1B_DATA0__GPIO4_IO_24	0x0b0b0
+		>;
+	};
+
+	pinctrl_hog: hoggrp {
+		fsl,pins = <
+			MX6SX_PAD_NAND_CE0_B__GPIO4_IO_1	0x1b0b0
+			MX6SX_PAD_NAND_CLE__GPIO4_IO_3		0x1b0b0
+			MX6SX_PAD_NAND_RE_B__GPIO4_IO_12	0x1b0b0
+			MX6SX_PAD_NAND_WE_B__GPIO4_IO_14	0x1b0b0
+			MX6SX_PAD_NAND_WP_B__GPIO4_IO_15	0x1b0b0
+			MX6SX_PAD_NAND_READY_B__GPIO4_IO_13	0x1b0b0
+			MX6SX_PAD_QSPI1A_DATA0__GPIO4_IO_16	0x1b0b0
+			MX6SX_PAD_QSPI1A_DATA1__GPIO4_IO_17	0x1b0b0
+			MX6SX_PAD_QSPI1A_DATA2__GPIO4_IO_18	0x1b0b0
+			MX6SX_PAD_QSPI1A_DATA3__GPIO4_IO_19	0x1b0b0
+			MX6SX_PAD_SD1_CMD__CCM_CLKO1		0x000b0
+			MX6SX_PAD_SD3_DATA5__GPIO7_IO_7		0x1b0b0
+			/* Test points */
+			MX6SX_PAD_NAND_DATA04__GPIO4_IO_8	0x1b0b0
+			MX6SX_PAD_QSPI1B_DATA1__GPIO4_IO_25	0x1b0b0
+		>;
+	};
+
+	pinctrl_i2c1: i2c1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO00__I2C1_SCL		0x4001b8b1
+			MX6SX_PAD_GPIO1_IO01__I2C1_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO02__I2C2_SCL		0x4001b8b1
+			MX6SX_PAD_GPIO1_IO03__I2C2_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_i2c3: i2c3grp {
+		fsl,pins = <
+			MX6SX_PAD_KEY_COL4__I2C3_SCL		0x4001b8b1
+			MX6SX_PAD_KEY_ROW4__I2C3_SDA		0x4001b8b1
+		>;
+	};
+
+	pinctrl_lcdif1: lcdif1grp {
+		fsl,pins = <
+			MX6SX_PAD_LCD1_CLK__LCDIF1_CLK		0x4001b0b0
+			MX6SX_PAD_LCD1_ENABLE__LCDIF1_ENABLE	0x4001b0b0
+			MX6SX_PAD_LCD1_HSYNC__LCDIF1_HSYNC	0x4001b0b0
+			MX6SX_PAD_LCD1_VSYNC__LCDIF1_VSYNC	0x4001b0b0
+			MX6SX_PAD_LCD1_RESET__GPIO3_IO_27	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA00__LCDIF1_DATA_0	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA01__LCDIF1_DATA_1	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA02__LCDIF1_DATA_2	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA03__LCDIF1_DATA_3	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA04__LCDIF1_DATA_4	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA05__LCDIF1_DATA_5	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA06__LCDIF1_DATA_6	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA07__LCDIF1_DATA_7	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA08__LCDIF1_DATA_8	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA09__LCDIF1_DATA_9	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA10__LCDIF1_DATA_10	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA11__LCDIF1_DATA_11	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA12__LCDIF1_DATA_12	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA13__LCDIF1_DATA_13	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA14__LCDIF1_DATA_14	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA15__LCDIF1_DATA_15	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA16__LCDIF1_DATA_16	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA17__LCDIF1_DATA_17	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA18__LCDIF1_DATA_18	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA19__LCDIF1_DATA_19	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA20__LCDIF1_DATA_20	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA21__LCDIF1_DATA_21	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA22__LCDIF1_DATA_22	0x4001b0b0
+			MX6SX_PAD_LCD1_DATA23__LCDIF1_DATA_23	0x4001b0b0
+		>;
+	};
+
+	pinctrl_pcie: pciegrp {
+		fsl,pins = <
+			MX6SX_PAD_NAND_DATA05__GPIO4_IO_9	0xb0b0
+			MX6SX_PAD_NAND_DATA06__GPIO4_IO_10	0xb0b0
+			MX6SX_PAD_NAND_DATA07__GPIO4_IO_11	0xb0b0
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO13__PWM4_OUT		0x110b0
+		>;
+	};
+
+	pinctrl_reg_wlan: reg-wlangrp {
+		fsl,pins = <
+			MX6SX_PAD_SD3_DATA4__GPIO7_IO_6		0x1b0b0
+			MX6SX_PAD_GPIO1_IO11__CCM_CLKO1		0x000b0
+		>;
+	};
+
+	pinctrl_sgtl5000: sgtl5000grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO12__CCM_CLKO2		0x000b0
+			MX6SX_PAD_ENET1_COL__GPIO2_IO_0		0x1b0b0
+			MX6SX_PAD_ENET1_CRS__GPIO2_IO_1		0x1b0b0
+			MX6SX_PAD_QSPI1A_SS0_B__GPIO4_IO_22	0xb0b0
+		>;
+	};
+
+	pinctrl_uart1: uart1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO04__UART1_TX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO05__UART1_RX		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart2: uart2grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO06__UART2_TX		0x1b0b1
+			MX6SX_PAD_GPIO1_IO07__UART2_RX		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart3: uart3grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1B_SS0_B__UART3_TX	0x1b0b1
+			MX6SX_PAD_QSPI1B_SCLK__UART3_RX		0x1b0b1
+		>;
+	};
+
+	pinctrl_uart5: uart5grp {
+		fsl,pins = <
+			MX6SX_PAD_KEY_COL3__UART5_TX		0x1b0b1
+			MX6SX_PAD_KEY_ROW3__UART5_RX		0x1b0b1
+			MX6SX_PAD_SD3_DATA6__UART3_RTS_B	0x1b0b1
+			MX6SX_PAD_SD3_DATA7__UART3_CTS_B	0x1b0b1
+		>;
+	};
+
+	pinctrl_usbotg1: usbotg1grp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO08__USB_OTG1_OC	0x1b0b0
+			MX6SX_PAD_GPIO1_IO10__ANATOP_OTG1_ID	0x170b1
+		>;
+	};
+
+	pinctrl_usbotg1_vbus: usbotg1-vbusgrp {
+		fsl,pins = <
+			MX6SX_PAD_GPIO1_IO09__GPIO1_IO_9	0x1b0b0
+		>;
+	};
+
+	pinctrl_usbotg2: usbotg2grp {
+		fsl,pins = <
+			MX6SX_PAD_QSPI1B_DATA2__GPIO4_IO_26	0xb0b0
+		>;
+	};
+
+	pinctrl_usdhc2: usdhc2grp {
+		fsl,pins = <
+			MX6SX_PAD_SD2_CMD__USDHC2_CMD		0x17059
+			MX6SX_PAD_SD2_CLK__USDHC2_CLK		0x10059
+			MX6SX_PAD_SD2_DATA0__USDHC2_DATA0	0x17059
+			MX6SX_PAD_SD2_DATA1__USDHC2_DATA1	0x17059
+			MX6SX_PAD_SD2_DATA2__USDHC2_DATA2	0x17059
+			MX6SX_PAD_SD2_DATA3__USDHC2_DATA3	0x17059
+			MX6SX_PAD_KEY_COL2__GPIO2_IO_12		0x1b0b0
+		>;
+	};
+
+	pinctrl_usdhc3: usdhc3grp {
+		fsl,pins = <
+			MX6SX_PAD_SD3_CLK__USDHC3_CLK		0x10071
+			MX6SX_PAD_SD3_CMD__USDHC3_CMD		0x17071
+			MX6SX_PAD_SD3_DATA0__USDHC3_DATA0	0x17071
+			MX6SX_PAD_SD3_DATA1__USDHC3_DATA1	0x17071
+			MX6SX_PAD_SD3_DATA2__USDHC3_DATA2	0x17071
+			MX6SX_PAD_SD3_DATA3__USDHC3_DATA3	0x17071
+		>;
+	};
+
+	pinctrl_usdhc4_50mhz: usdhc4-50mhzgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x10071
+			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x17071
+			MX6SX_PAD_SD4_RESET_B__USDHC4_RESET_B	0x17071
+			MX6SX_PAD_SD4_DATA0__USDHC4_DATA0	0x17071
+			MX6SX_PAD_SD4_DATA1__USDHC4_DATA1	0x17071
+			MX6SX_PAD_SD4_DATA2__USDHC4_DATA2	0x17071
+			MX6SX_PAD_SD4_DATA3__USDHC4_DATA3	0x17071
+			MX6SX_PAD_SD4_DATA4__USDHC4_DATA4	0x17071
+			MX6SX_PAD_SD4_DATA5__USDHC4_DATA5	0x17071
+			MX6SX_PAD_SD4_DATA6__USDHC4_DATA6	0x17071
+			MX6SX_PAD_SD4_DATA7__USDHC4_DATA7	0x17071
+		>;
+	};
+
+	pinctrl_usdhc4_100mhz: usdhc4-100mhzgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x100b9
+			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x170b9
+			MX6SX_PAD_SD4_DATA0__USDHC4_DATA0	0x170b9
+			MX6SX_PAD_SD4_DATA1__USDHC4_DATA1	0x170b9
+			MX6SX_PAD_SD4_DATA2__USDHC4_DATA2	0x170b9
+			MX6SX_PAD_SD4_DATA3__USDHC4_DATA3	0x170b9
+			MX6SX_PAD_SD4_DATA4__USDHC4_DATA4	0x170b9
+			MX6SX_PAD_SD4_DATA5__USDHC4_DATA5	0x170b9
+			MX6SX_PAD_SD4_DATA6__USDHC4_DATA6	0x170b9
+			MX6SX_PAD_SD4_DATA7__USDHC4_DATA7	0x170b9
+		>;
+	};
+
+	pinctrl_usdhc4_200mhz: usdhc4-200mhzgrp {
+		fsl,pins = <
+			MX6SX_PAD_SD4_CLK__USDHC4_CLK		0x100f9
+			MX6SX_PAD_SD4_CMD__USDHC4_CMD		0x170f9
+			MX6SX_PAD_SD4_DATA0__USDHC4_DATA0	0x170f9
+			MX6SX_PAD_SD4_DATA1__USDHC4_DATA1	0x170f9
+			MX6SX_PAD_SD4_DATA2__USDHC4_DATA2	0x170f9
+			MX6SX_PAD_SD4_DATA3__USDHC4_DATA3	0x170f9
+			MX6SX_PAD_SD4_DATA4__USDHC4_DATA4	0x170f9
+			MX6SX_PAD_SD4_DATA5__USDHC4_DATA5	0x170f9
+			MX6SX_PAD_SD4_DATA6__USDHC4_DATA6	0x170f9
+			MX6SX_PAD_SD4_DATA7__USDHC4_DATA7	0x170f9
+		>;
+	};
+};
-- 
2.7.0




More information about the linux-arm-kernel mailing list