[PATCH 2/3] thermal: Add Mediatek thermal controller support
Punit Agrawal
punit.agrawal at arm.com
Wed Sep 30 02:36:14 PDT 2015
Hi Sascha,
Re-posting a comment from v7. Perhaps you missed it...
Sascha Hauer <s.hauer at pengutronix.de> writes:
> This adds support for the Mediatek thermal controller found on MT8173
> and likely other SoCs.
> The controller is a bit special. It does not have its own ADC, instead
> it controls the on-SoC AUXADC via AHB bus accesses. For this reason
> we need the physical address of the AUXADC. Also it controls a mux
> using AHB bus accesses, so we need the APMIXEDSYS physical address aswell.
>
> Signed-off-by: Sascha Hauer <s.hauer at pengutronix.de>
> Reviewed-by: Daniel Kurtz <djkurtz at chromium.org>
> ---
> drivers/thermal/Kconfig | 8 +
> drivers/thermal/Makefile | 1 +
> drivers/thermal/mtk_thermal.c | 537 ++++++++++++++++++++++++++++++++++++++++++
> 3 files changed, 546 insertions(+)
> create mode 100644 drivers/thermal/mtk_thermal.c
>
> diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
> index 0390044..dadd1eb 100644
> --- a/drivers/thermal/Kconfig
> +++ b/drivers/thermal/Kconfig
> @@ -348,6 +348,14 @@ config INTEL_PCH_THERMAL
> Thermal reporting device will provide temperature reading,
> programmable trip points and other information.
>
> +config MTK_THERMAL
> + tristate "Temperature sensor driver for mediatek SoCs"
> + depends on ARCH_MEDIATEK || COMPILE_TEST
> + default y
> + help
> + Enable this option if you want to have support for thermal management
> + controller present in Mediatek SoCs
> +
> menu "Texas Instruments thermal drivers"
> source "drivers/thermal/ti-soc-thermal/Kconfig"
> endmenu
> diff --git a/drivers/thermal/Makefile b/drivers/thermal/Makefile
> index 26f1608..5f979e7 100644
> --- a/drivers/thermal/Makefile
> +++ b/drivers/thermal/Makefile
> @@ -45,3 +45,4 @@ obj-$(CONFIG_INTEL_PCH_THERMAL) += intel_pch_thermal.o
> obj-$(CONFIG_ST_THERMAL) += st/
> obj-$(CONFIG_TEGRA_SOCTHERM) += tegra_soctherm.o
> obj-$(CONFIG_HISI_THERMAL) += hisi_thermal.o
> +obj-$(CONFIG_MTK_THERMAL) += mtk_thermal.o
> diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
> new file mode 100644
> index 0000000..6be1a6c
> --- /dev/null
> +++ b/drivers/thermal/mtk_thermal.c
> @@ -0,0 +1,537 @@
> +/*
> + * Copyright (c) 2015 MediaTek Inc.
> + * Author: Hanyi Wu <hanyi.wu at mediatek.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/of_irq.h>
> +#include <linux/platform_device.h>
> +#include <linux/slab.h>
> +#include <linux/thermal.h>
> +#include <linux/reset.h>
> +#include <linux/time.h>
> +#include <linux/types.h>
> +#include <dt-bindings/thermal/mt8173.h>
> +
> +/* AUXADC Registers */
> +#define AUXADC_CON0_V 0x000
> +#define AUXADC_CON1_V 0x004
> +#define AUXADC_CON1_SET_V 0x008
> +#define AUXADC_CON1_CLR_V 0x00c
> +#define AUXADC_CON2_V 0x010
> +#define AUXADC_DATA(channel) (0x14 + (channel) * 4)
> +#define AUXADC_MISC_V 0x094
> +
> +#define AUXADC_CON1_CHANNEL(x) BIT(x)
> +
> +#define APMIXED_SYS_TS_CON1 0x604
> +
> +/* Thermal Controller Registers */
> +#define TEMP_MONCTL0 0x000
> +#define TEMP_MONCTL1 0x004
> +#define TEMP_MONCTL2 0x008
> +#define TEMP_MONIDET0 0x014
> +#define TEMP_MONIDET1 0x018
> +#define TEMP_MSRCTL0 0x038
> +#define TEMP_AHBPOLL 0x040
> +#define TEMP_AHBTO 0x044
> +#define TEMP_ADCPNP0 0x048
> +#define TEMP_ADCPNP1 0x04c
> +#define TEMP_ADCPNP2 0x050
> +#define TEMP_ADCPNP3 0x0b4
> +
> +#define TEMP_ADCMUX 0x054
> +#define TEMP_ADCEN 0x060
> +#define TEMP_PNPMUXADDR 0x064
> +#define TEMP_ADCMUXADDR 0x068
> +#define TEMP_ADCENADDR 0x074
> +#define TEMP_ADCVALIDADDR 0x078
> +#define TEMP_ADCVOLTADDR 0x07c
> +#define TEMP_RDCTRL 0x080
> +#define TEMP_ADCVALIDMASK 0x084
> +#define TEMP_ADCVOLTAGESHIFT 0x088
> +#define TEMP_ADCWRITECTRL 0x08c
> +#define TEMP_MSR0 0x090
> +#define TEMP_MSR1 0x094
> +#define TEMP_MSR2 0x098
> +#define TEMP_MSR3 0x0B8
> +
> +#define TEMP_SPARE0 0x0f0
> +
> +#define PTPCORESEL 0x400
> +
> +#define TEMP_MONCTL1_PERIOD_UNIT(x) ((x) & 0x3ff)
> +
> +#define TEMP_MONCTL2_FILTER_INTERVAL(x) (((x) & 0x3ff)) << 16
> +#define TEMP_MONCTL2_SENSOR_INTERVAL(x) ((x) & 0x3ff)
> +
> +#define TEMP_AHBPOLL_ADC_POLL_INTERVAL(x) (x)
> +
> +#define TEMP_ADCWRITECTRL_ADC_PNP_WRITE BIT(0)
> +#define TEMP_ADCWRITECTRL_ADC_MUX_WRITE BIT(1)
> +
> +#define TEMP_ADCVALIDMASK_VALID_HIGH BIT(5)
> +#define TEMP_ADCVALIDMASK_VALID_POS(bit) (bit)
> +
> +#define MT8173_TS1 0
> +#define MT8173_TS2 1
> +#define MT8173_TS3 2
> +#define MT8173_TS4 3
> +#define MT8173_TSABB 4
> +
> +/* AUXADC channel 11 is used for the temperature sensors */
> +#define MT8173_TEMP_AUXADC_CHANNEL 11
> +
> +/* The total number of temperature sensors in the MT8173 */
> +#define MT8173_NUM_SENSORS 5
> +
> +/* The number of banks in the MT8173 */
> +#define MT8173_NUM_ZONES 4
> +
> +/* The number of sensing points per bank */
> +#define MT8173_NUM_SENSORS_PER_ZONE 4
> +
> +#define THERMAL_NAME "mtk-thermal"
> +
> +struct mtk_thermal;
> +
> +struct mtk_thermal_bank {
> + struct mtk_thermal *mt;
> + struct thermal_zone_device *tzd;
> + int id;
> +};
> +
> +struct mtk_thermal {
> + struct device *dev;
> + void __iomem *thermal_base;
> +
> + struct clk *clk_peri_therm;
> + struct clk *clk_auxadc;
> +
> + struct mtk_thermal_bank banks[MT8173_NUM_ZONES];
> +
> + struct mutex lock;
> +
> + /* Calibration values */
> + int calib_slope;
> + int calib_offset;
> +};
> +
> +struct mtk_thermal_bank_cfg {
> + unsigned int num_sensors;
> + unsigned int sensors[MT8173_NUM_SENSORS_PER_ZONE];
> +};
> +
> +static const int sensor_mux_values[MT8173_NUM_SENSORS] = { 0, 1, 2, 3, 16 };
> +
> +/*
> + * The MT8173 thermal controller has four banks. Each bank can read up to
> + * four temperature sensors simultaneously. The MT8173 has a total of 5
> + * temperature sensors. We use each bank to measure a certain area of the
> + * SoC. Since TS2 is located centrally in the SoC it is influenced by multiple
> + * areas, hence is used in different banks.
> + */
> +static const struct mtk_thermal_bank_cfg bank_data[] = {
> + [MT8173_THERMAL_ZONE_CA53] = {
> + .num_sensors = 2,
> + .sensors = { MT8173_TS2, MT8173_TS3 },
> + },
> +
> + [MT8173_THERMAL_ZONE_CA57] = {
> + .num_sensors = 2,
> + .sensors = { MT8173_TS2, MT8173_TS4 },
> + },
> +
> + [MT8173_THERMAL_ZONE_GPU] = {
> + .num_sensors = 3,
> + .sensors = { MT8173_TS1, MT8173_TS2, MT8173_TSABB },
> + },
> +
> + [MT8173_THERMAL_ZONE_CORE] = {
> + .num_sensors = 1,
> + .sensors = { MT8173_TS2 },
> + },
> +};
> +
> +struct mtk_thermal_sense_point {
> + int msr;
> + int adcpnp;
> +};
> +
> +static const struct mtk_thermal_sense_point
> + sensing_points[MT8173_NUM_SENSORS_PER_ZONE] = {
> + {
> + .msr = TEMP_MSR0,
> + .adcpnp = TEMP_ADCPNP0,
> + }, {
> + .msr = TEMP_MSR1,
> + .adcpnp = TEMP_ADCPNP1,
> + }, {
> + .msr = TEMP_MSR2,
> + .adcpnp = TEMP_ADCPNP2,
> + }, {
> + .msr = TEMP_MSR3,
> + .adcpnp = TEMP_ADCPNP3,
> + },
> +};
> +
> +/**
> + * raw_to_mcelsius - convert a raw ADC value to mcelsius
> + * @mt: The thermal controller
> + * @raw: raw ADC value
> + *
> + * This converts the raw ADC value to mcelsius using the SoC specific
> + * calibration constants
> + */
> +static int raw_to_mcelsius(struct mtk_thermal *mt, u32 raw)
> +{
> + return mt->calib_offset + mt->calib_slope * (raw & 0xfff);
> +}
> +
> +/**
> + * mtk_thermal_get_bank - get bank
> + * @bank: The bank
> + *
> + * The bank registers are banked, we have to select a bank in the
> + * PTPCORESEL register to access it.
> + */
> +static void mtk_thermal_get_bank(struct mtk_thermal_bank *bank)
> +{
> + struct mtk_thermal *mt = bank->mt;
> + u32 val;
> +
> + mutex_lock(&mt->lock);
> +
> + val = readl(mt->thermal_base + PTPCORESEL);
> + val &= ~0xf;
> + val |= bank->id;
> + writel(val, mt->thermal_base + PTPCORESEL);
> +}
> +
> +/**
> + * mtk_thermal_put_bank - release bank
> + * @bank: The bank
> + *
> + * release a bank previously taken with mtk_thermal_get_bank,
> + */
> +static void mtk_thermal_put_bank(struct mtk_thermal_bank *bank)
> +{
> + struct mtk_thermal *mt = bank->mt;
> +
> + mutex_unlock(&mt->lock);
> +}
> +
> +/**
> + * mtk_thermal_bank_temperature - get the temperature of a bank
> + * @bank: The bank
> + *
> + * The temperature of a bank is considered the maximum temperature of
> + * the sensors associated to the bank.
> + */
> +static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
> +{
> + struct mtk_thermal *mt = bank->mt;
> + int temp, i, max;
> + u32 raw;
> +
> + temp = max = INT_MIN;
> +
> + for (i = 0; i < bank_data[bank->id].num_sensors; i++) {
> + raw = readl(mt->thermal_base + sensing_points[i].msr);
> +
> + temp = raw_to_mcelsius(mt, raw);
> +
> + /*
> + * The first read of a sensor often contains very high bogus
> + * temperature value. Filter these out so that the system does
> + * not immediately shut down.
> + */
> + if (temp > 200000)
> + temp = 0;
> +
If the bogus value is only the first time the sensor is read, instead of
filtering here, you could call mtk_thermal_bank_temperature at probe
time when you are initialising the banks and ignore the returned value.
Thanks,
Punit
> + if (temp > max)
> + max = temp;
> + }
> +
> + return max;
> +}
> +
[...]
More information about the linux-arm-kernel
mailing list