[PATCH] arm: dts: berlin2q-marvell-dmp: add sdhci1 fully functionality

Jisheng Zhang jszhang at marvell.com
Mon Nov 30 05:54:39 PST 2015


The sdhci1 on Marvell BG2Q DMP board is used as sdcard interface, we
have gpios for card detection, write-protect, vqmmc and vmmc.

This patch adds pinmux for this sdcard interface, then adds regulators
for vmmc and vqmmc, lastly adds cd-gpios, wp-gpios properties.

Signed-off-by: Jisheng Zhang <jszhang at marvell.com>
---
since v1:
 - move sd1_pmux to soc dtsi
 - remove cd-inverted and make cd-gpio GPIO_ACTIVE_LOW

 arch/arm/boot/dts/berlin2q-marvell-dmp.dts | 37 ++++++++++++++++++++++++++++--
 arch/arm/boot/dts/berlin2q.dtsi            |  5 ++++
 2 files changed, 40 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
index cdcf89b..33b2875 100644
--- a/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
+++ b/arch/arm/boot/dts/berlin2q-marvell-dmp.dts
@@ -84,12 +84,45 @@
 			gpio = <&portb 12 GPIO_ACTIVE_HIGH>;
 			enable-active-high;
 		};
+
+		reg_sdio1_vmmc: regulator at 3 {
+			compatible = "regulator-fixed";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-name = "sdio1_vmmc";
+			enable-active-high;
+			regulator-boot-on;
+			gpio = <&portb 21 GPIO_ACTIVE_HIGH>;
+		};
+
+		reg_sdio1_vqmmc: regulator at 4 {
+			compatible = "regulator-gpio";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-name = "sdio1_vqmmc";
+			regulator-type = "voltage";
+			enable-active-high;
+			gpios = <&portb 16 GPIO_ACTIVE_HIGH>;
+			states = <3300000 0x1
+				  1800000 0x0>;
+		};
+	};
+};
+
+&soc_pinctrl {
+	sd1gpio_pmux: sd1pwr-pmux {
+		groups = "G23", "G32";
+		function = "gpio";
 	};
 };
 
 &sdhci1 {
-	broken-cd;
-	sdhci,wp-inverted;
+	vmmc-supply = <&reg_sdio1_vmmc>;
+	vqmmc-supply = <&reg_sdio1_vqmmc>;
+	cd-gpios = <&portc 30 GPIO_ACTIVE_LOW>;
+	wp-gpios = <&portd 0 GPIO_ACTIVE_HIGH>;
+	pinctrl-0 = <&sd1gpio_pmux>, <&sd1_pmux>;
+	pinctrl-names = "default";
 	status = "okay";
 };
 
diff --git a/arch/arm/boot/dts/berlin2q.dtsi b/arch/arm/boot/dts/berlin2q.dtsi
index 8ea177f..73a9362 100644
--- a/arch/arm/boot/dts/berlin2q.dtsi
+++ b/arch/arm/boot/dts/berlin2q.dtsi
@@ -417,6 +417,11 @@
 			soc_pinctrl: pin-controller {
 				compatible = "marvell,berlin2q-soc-pinctrl";
 
+				sd1_pmux: sd1-pmux {
+					groups = "G31";
+					function = "sd1";
+				};
+
 				twsi0_pmux: twsi0-pmux {
 					groups = "G6";
 					function = "twsi0";
-- 
2.6.2




More information about the linux-arm-kernel mailing list